R/C Marine Parts & Accessories
Gizmomotors WBR-PRO-MOD-1048-CARB, Gizmos racing Mod Wt-1048 big bore carb
WBR-PRO-MOD-1048-CARB, Gizmos racing Mod Wt-1048 big bore carb Gizmo's Racing modified Walbro WT-1048 carburetor is bored and the mouth of the carb has a radius inlet to allow a smooth and even entry of air into the intake duct with the flow stream adhering to the carb walls.The flow-contoured entry is designed to reduce boundary layer disturbance as high velocity air enters the intake path. Results include improved air stability and increased engine performance.**The carburetor also comes with the needle clamp**NOTE: THESE ARE PORTED ON A CNC MACHINE SO WE CAN GET PRECISE BORE SIZE EVERY TIME.All our Carburetors are Genuine OEM Walbro and not the copies that are being sold as OEM.
$69.99
Gizmomotors Stainless Steel Hot Pipe Springs
Stainless Steel Hot Pipe Springs G.Z.R. Stainless steel Hot pipe Springs Please note these springs are sold as a set of 3 sizes which will fit any size spacer you will need to use.
$16.99
Speedmaster SPDPM-009, Large Pipe Grommet
SPDPM-009, Large Pipe Grommet
$4.99
Speedmaster SPDZE-002, 5/8 Silicone Coupler
SPDZE-002, 5/8 Silicone Coupler
$8.99
OSE ZTW-300-7300410, Seal Series ESC G2: 300A OPTO 6s-14s
ZTW-300-7300410, Seal Series ESC G2: 300A OPTO 6s-14s ZTW SEAL G2 Series 300 v2 : OPTO 6s-14s : 300 amps : Lipo Brushless ESC Following up on the success of the ZTW 300, ZTW has released a 32-bit version of the Seal 300. The Seal G2 comes in a new compact design that is a full 100 grams lighter, shorter, and narrower than its predecessor. The 32-bit Microcontroller supports the "CAN protocol" for recording data. The ESC can be programmed by the optional LCD prog card or the mobile phone APP (need extra Bluetooth), and supports real-time data. More info will be coming.The ZTW SEAL G2 Series is designed specifically for RC Boat applications, featuring a waterproof design. The 300A ESC includes two water cooling pipes as well as customized heat sinks. However, the 300A ESC does not offer a built-in BEC, requiring an additional battery pack to operate the servo. In order to protect the boat, the ESC offers a power reduction when too hot and an optional Low Voltage Cutoff. For more specific information, see the specs below... Specs:The waterproof design (rates as IP 67) allows this ESC to work in wet conditions.Continuous Current (A): 300 AmpsBurst Current(A): XXX AmpsVoltage: 6s - 14s Lipo (18-42 NiMH)Power Wire: 8 Gauge160mm-Red/160mm-BlackMotor Wire 8 Gauge 160mm-BlackBattery Eliminator Circuit (BEC): None, requires RX pack or BEC Eliminator Circuit. The throttle works in both forward and reverse or you can lock out the reverse function for racing safety.Optional programming with LCD programming card.Case dimensions (not including wires):Length: 130mm (5.12")Width: 65mm (2.56")Height: 38mm (1.50")Weight: 530gWater fitting thread size: m6Includes: Everything in picture number oneRequires: Connectors, 8mm bullet connectors or larger.
$429.99
OSE LEO-2860-X2, Leopard 2860 X2 Motor
LEO-2860-X2, Leopard 2860 X2 Motor 28mm Diameter by 64mm Long Brushless Motor by Leopard Power. Hand wound for high efficiency of up to 85%. Comes with high quality bearings and neodymium magnets for high power. Vent cutouts in the front and rear end bells allow air to circulate for additional cooling. Specifications: Magnets: Neodymium Watts: 600 with upto 1200 burst. Poles: 4 Motor Shaft Diameter: 4mm with flat spot Can Measures: 28mm diameter x 64mm long Weight: 190 Grams Mounting screw diameter required: 3mm threads. Mounting Holes: 2 mounting patterns for ease of installation. Both 16mm & 19mm apart. Works with all the 380 Motor mounts we sell. Includes Leopard male bullet plugs soldered to the motor and a matching set for your esc connection
$64.99
OSE OSE-1345, OSE Aluminum coupler: 4mm Motor
OSE-80402, OSE Auto Bailer OSE Aluminum coupler. 4mm - .150" (3.75mm) Specs:22mm long x 10mm diameter(2) 4mm grub screws .7 pitch
$8.99
OSE OSE-80402, OSE Auto Bailer
OSE-80402, OSE Auto Bailer Use this to help get rid of water in you hull. The aluminum bailer has a small plastic ball that moves to allow water to exit your hull while your running your boat, but when your boat is at rest the outside water pressure pushes the ball into a seal that closes the hole.Measures:approx 25mm long x 10mm diameter.
$8.99
Leopard LEO-4092, Leopard 4092 1480 Kv Motor w/ Water Cooling Jacket
LEO-4092, Leopard 4092 1480 Kv Motor w/ Water Cooling Jacket Leopard 4092 brushless motor.40mm Diameter by 92mm Long Brushless Motor by Leopard Power. Hand wound for high efficiency of up to 90%. Comes with high quality bearings and neodymium magnets for high power. Includes endbells that are assembled with screws for both strength and ease of maintenance. Motor Specs:Magnets: neodymiumWatts: 2600 with Over 4200 Burst.Poles: 4Motor Shaft: 5mm with flat spotCan Measures: 40mm diameter x 92mm longWeight: 492 GramsMounting screw diameter required: 3mmBearing size: 5mm wide x 16mm od x 5mm idMounting Holes 25mm apart for use with most 540 mounts. Includes Leopard 6.0mm male bullet plugs soldered to the motor and a matching set for your esc connection. The Leopard Red anodized aluminum water cooling jacket is designed to allow water to come in direct contact with the motor and flow around it allowing maximum cooling.Installation is a snap!Apply some oil to both your motor housing and o-rings, then slide on the jacket. Water Cooling Jacket Specs:Outside diameter 47mm.Length 50mm Long. This product was added to our catalog on June 1, 2023
$149.99
RaCersEdge™ BZN540120, Chassis, Smyter
Chassis, Smyter
$18.99
RaCersEdge™ RCE6409, Servo (3-Wire Plug, for Brushless ESC Upgrade) for Blackzon Slyder
Servo (3-Wire Plug, for Brushless ESC Upgrade) for Blackzon Slyder
$17.99
Speedmaster SPDR-012-DU-4, Straight Back D/P Rudder Assembly
SPDR-012-DU-4, Straight Back D/P Rudder Assembly
$56.99
Speedmaster spdrs-009-21dut, Speedmaster 21 Rudder Assembly w/ Extended Tee Bracket
spdrs-009-21, Speedmaster 21 Rudder Assembly w/ Extended Tee Bracket
$59.99
Speedmaster SPDT-150, Speedmaster 1.5" x 1.5" Adjustable Metal Trim Tabs (2 Pairs)
SPDT-150, Speedmaster 1.5" x 1.5" Adjustable Metal Trim Tabs (2 Pairs) Speedmaster 1 1/2" x 1 1/2" tabs. These tabs are perfect for dialing in any mono and at the same time saving some weight. CNC cut Aluminum adjusting bracket with stainless trim plate.Same as part number ros-spdt-150 but this package comes with (2) pairs of tabs.These adjustable trim tabs measure approx. 1.5" (38.10mm) wide x 1.5" (38.10mm) Long x .70" (17.80mm) height(2) pairs per pack.
$29.95
Speedmaster SPDSD-6090, Nitro, for 1/4" (.250") propeller shaft
SPDSD-6090: Nitro, for 1/4" (.250") propeller shaft. Speedmaster Stinger StrutIt can be quickly adjusted from positive to negative thrust angles. The bushing is cross drilled to hold grease for an extra smooth driveline. It is constructed with high quality aluminum and CNC cut to tight tolerances. This has been often copied by other manufactures but never truly has been duplicated.
$47.94
RaCersEdge™ MBP-CNC4795, Easy Move Fiberglass 90mm x 450mm battery tray
Easy Move Fiberglass 90mm x 450mm battery tray by MBP. The Easy Move tray allows for both the easy install / removal of lipo packs without the stress of having to use Velcro directly stuck on your packs. The downfall of using velcro directly on lipo packs is that the removal of the packs pulls & stresses the aluminum tabs connectors inside of the packs. This system removes that stress by allowing the battery to be strapped directly to the tray with Velcro straps and when you need to remove the battery simply unscrew one thumb screw and remove the pack with absolutely no stress to the pack. See the video on the bottom of this page.Another great feature is this system allows for the quick forward and backward adjustments for fine tune the balance of your boat.Specs:90mm (3.54") x 450mm (17.71") Weight: approx 481 gramsIncludes:(1) trayRequires: Velcro straps and installation into hull
$107.99
Speedmaster SPDSB-010-250F, EXT .250 STRUT BLD F/B
SPDSB-010-250F, EXT .250 STRUT BLD F/B
$17.96
Speedmaster SPDSB-014-225, 2 1/4" BEARING BLOCK
SPDSB-014-225, 2 1/4" BEARING BLOCK
$13.28
Speedmaster LEO-56110, Leopard 56110 Motor
Leopard 56110 brushless motorSpecial while supplies last, includes water Jacket with Leopard Motor Purchase!56mm Diameter x 110mm Long Brushless Motor by Leopard Power. Hand wound for high efficiency of up to 90%.Comes with high quality bearings and neodymium magnets for high power. Includes endbells that are assembled with screws for both strength and ease of maintenance.Specs:Magnets: NeodymiumWatts: 5000 with Over 6000 Burst.Poles: 4Motor Shaft: 8mmCan Measures: 56mm diameter x 110mm longMounting screw diameter required: 4mmMounting Holes 30mm apartWeighs: 40.5 ouncesBearing size: 8mm wide x 19mm od x 6mm idIncludes Leopard 6.0mm male bullet plugs soldered to the motor and a matching set for your esc connection. OSE Suggests 20,000-35,000 total rpm for boats. We suggest most Fast Electric Boaters should run in the 25,000RPM range for Sport Boating or 30,000RPM Range for racing. These are only guidelines, we suggest if you do not have the knowledge to pick the correct motor, please consult us first or other members of the rc fast electric boating community. Either at a local club or on our OSE Forums.
$233.99
Speedmaster OCT-X465R, OCTURA PROPELLER
Diameter: 2.56"Total Pitch: 1.4x2.56=3.584"Shaft Size: 3/16"Attention! This prop is made for boat that require a clockwise spinning prop!
$34.99
Octura OCT-x457sb, Octura x457 - Sharpened & Balanced
OCT-x457sb, Octura x457 - Sharpened & Balanced
$26.87
Octura OCT-x430, Octura x430
OCT-x430, Octura x430
$19.99
Octura OCT-x430r, Octura x430r
OCT-x430r, Octura x430r
$19.99
Octura OCT-x457r, Octura x457r
OCT-x457r, Octura x457r
$26.99
Octura OCT-x460, Octura x460
OCT-x460, Octura x460
$31.99
Octura OCT-x455, Octura x455
OCT-x455, Octura x455
$26.99
RaCersEdge™ RCE-1100, Instant Stick Foam Saddle Tape (4')
RCE-1100, Instant Stick Foam Saddle Tape (4')
$3.79
RaCersEdge™ RCE-532B42-R (Red Water Cooling Jacket 40mm x 50mm Long)
RCE-532B42-R (Red Water Cooling Jacket 40mm x 50mm Long)
$24.95
Leopard LEO-4082X2, Leopard 4082X2, 2200Kv X2 1.5Y Brushless Motor
LEO-4082X2, Leopard 4082X2, 2200Kv X2 1.5Y Brushless Motor Leopard 4082 brushless motor.The Leopard has been the standard in High value/High quality at a low cost motor on the market. Leopard has released a new version of the popular 1600kv and 2200kv sizes, called the X2.40mm Diameter by 82mm Long Brushless Motor by Leopard Power. Hand wound for high efficiency of up to 90%. Comes with high quality bearings and neodymium magnets for high power. Includes end-bells that are assembled with screws for both strength and ease of maintenance.
$149.95
RaCersEdge™ RCE-CNC, Carburetor Needle Clamp
RCE-CNC, Carburetor Needle Clamp
$3.00
RaCersEdge™ RCE-019-508B30, Exhaust Pipe Sleeve
RCE-019-508B30, Exhaust Pipe Sleeve
$10.00
Gizmomotors RCESSHP90, RCE Stainless Steel Hot Pipe Complete, 90 Degrees
RCESSHP90, RCE Stainless Steel Hot Pipe Complete Size Variation 90 Degrees Spacers are 2-5/8, 2-3/4, 3-inch, 3-1/4 inch
$169.00
Gizmomotors GZR-Zubernuts, 1/4" Zuber Prop Nuts
GZR-Zubernuts, 1/4" Zuber Prop Nuts
$1.00
Gizmomotors GZ0007, Aluminum Dual Servo Mount for Standard Size Servo
GZ0007, Aluminum Dual Servo Mount for Standard Size Servo
$10.75
Gizmomotors GMM-238, All In One No Leak Manifold
GMM-238, All In One No Leak Manifold
$39.00
Speedmaster SPDMR-580, Speedmaster Motor Mount Cushion – 5/8 in.
SPDMR-580, 5/8" Motor Mount Cushion (4 required)
$2.30
DU-BRO DUM2021, 4.8V Electric Motor: 16-20" Boats
DUM2021, 4.8V Electric Motor: 16-20" Boats Product Details Key Features Ideal for Boats 16" - 20" Long Operates on 4.8 - 7.2V Output Shaft Has a Sleeve Pressed On That Allows It to Accept the Dumas Standard 1/8″ Coupling Assembly #2008 Also Fits the Dumas U.S.S. Bluefish Product Specifications Adjustable Timing No Application 16 - 20" long boats Input Voltage 4.8 - 7.2V Motor Type Brushed Outer Diameter 1.1" (28 mm) Part Type Electronics Product Length 2" (51 mm) Product Weight 2.2oz (62.4g)
$14.50
Speedmaster SPDSD-2140, 3/16" Shaft 3 Bolt Transom Bracket
3/16" Shaft 3 Bolt Transom Bracket
$39.95
Traxxas TRA5208 - Engine Multi-Shaft Marine with Recoil Starter
TRA5208 - Engine Multi-Shaft Marine with Recoil Starter
$199.99
Dynamite DYNM3875, 20A Brushless Marine ESC 2-6S DUAL CONNECTOR
DYNM3875, 20A Brushless Marine ESC 2-6S DUAL CONNECTOR Product Specifications Auto Cutoff Yes Battery Input Lead 12 AWG BEC Yes BEC Continous Current 5A BEC Maximum Burst Current 10A BEC Type Switching BEC Voltage 6V Brakes Yes Connector Type EC5 Forward Yes Input Voltage 2-6S LiPo, 6-18 Cells NiMH Low-Voltage Cutoff Programmable Yes Maximum Burst Current 720A Output Connector 5.5mm Bullet Overload Protection Yes Part Type Electronics Resistance .0005 ohms Reverse Yes Speed Control Marine Brushless Time Delay Brake Yes This product was added to our catalog on 03/04/2021
$159.99
Dynamite DYNM3865, 60A BL Marine ESC 2-3S
DYNM3865, 60A BL Marine ESC 2-3S Key Features Built in switch allows for easy change of battery chemistry type 14awg wires Large 4mm bullet brushless motor connectors Pre-wired with high-current EC3 connectors 60A single (not dual) battery configuration Overview Dynamite, known for it’s performance oriented, value priced aftermarket RC parts, accessories and electronics introduces its lineup of marine electronic speed controls designed specifically high performance marine applications. OEM for most Pro Boat models, Dynamite’s lineup of marine ESC’s offer users with speed controls engineered to meet the performance demands of today’s high speed RC powerboats. Available in varius configurations, each speed control comes built for complete water cooling and were designed to easily handle the power delivered from today’s high output Li-Po batteries. In addition, each ESC comes pre-wired with a NiMH/Li-Po switch providing an easy method of selecting NiMH or Li-Po battery types. Additional programming is easily managed through the optional LED program card. Product Specifications Specs Auto Cutoff Yes Battery Input Lead 3.25" BEC Yes BEC Continous Current 2A BEC Type Linear BEC Voltage 6V Brakes Yes Connector Type EC3 Forward Yes Input Voltage 2S?3S (7.4V?11.1V) Li-Po; 6C?9C (7.2V?10.8V) Ni-MH/Ni-Cd Low-Voltage Cutoff Programmable Yes Maximum Burst Current 360A Maximum Continuous Current 60A Motor Type Brushless Overload Protection Yes Part Type Electronics Product Height 1 in (25.6mm) Product Length 2.4 in (60.5mm) Product Weight 3.3 oz.(93 g) Product Width 1.5 in (38.5mm) Reverse Yes
$94.99
You have seen 89 out of 89 products