PTK-5129-19, ProTek RC 2S 100C Si-Graphene + HV LiPo Stick Pack TCS Battery (7.6V/5000mAh) The ProTek R/C 2S 100C Si-Graphene + HV LiPo Stick Pack Battery is built using a hard plastic case that is the same dimensions as a standard NiMH stick pack. This makes them a great choice for Tamiya TCS Series racing, including Euro Truck, all GT classes, M-Chassis and Formula One - as well as Euro Truck Racing League. Plus, its a great choice for any chassis that will accept a 6 cell NiMH stick pack. Weighing in at 235 grams, this Si-Graphene + HV battery weighs less than a standard 5000mAh LiPo battery of the same configuration - making your car lighter and faster! When compared to standard LiPo and LiHV, Silicon Graphene cells deliver improved efficiency, lower operating temperatures, lower internal resistance, increased run time, increased cycle life and increased voltage - but Graphene + 100C LiPo batteries take that a step further with more power and lower internal resistance when compared to the previous ProTek LiHV Graphene packs! This provides more runtime, and a dramatic increase in voltage and punch over the course of a run.   Lab testing has shown that ProTek R/C Silicon Graphene packs have double the cycle life when charged at 1C rates, and can be charged at higher amp rates with less risk of damage to the pack. More importantly, the discharge curve is flatter, meaning the cells maintain higher voltage throughout the discharge cycle with no significant drop off. Additionally, when compared to conventional LiPo batteries, Silicon Graphene batteries are lighter, providing a higher capacity per gram ratio. With 7.6V nominal voltage, 100C discharge ratings, incredibly high charge rates and huge variety of models to choose from, ProTek R/C 100C Graphene + packs are perfect for racers and bashers that demand the absolute best.   Features:  Perfect for Tamiya TCS Series racing Hard case is the same dimensions as a standard NiMH stick pack Lighter than a hardcase 2S LiPo pack of equal capacity  Improved power to weight ratio and a lower overall CG More runtime, with a dramatic increase in voltage and punch Silicone Graphene can handle more abuse and deliver more current than a standard LiPo battery Improved efficiency, lower operating temperatures, and lower internal resistance! Increased run time, increased cycle life and increased voltage! More capacity gram for gram when compared to standard LiPo cells  Perfect for stock class racers looking to shave grams 10C max charge rates - 1C charge rate recommended for longest life 7.6V nominal voltage Factory installed T-style plug NOTE: While these batteries are LiHV cells, they can still be charged the same as a standard LiPo with a standard LiPo charger. The overall voltage and capacity will be slightly less than when charged to LiHV specs, but the performance will be better than a standard LiPo thanks to the flat discharge curve, reduced weight and low internal resistance. When charged to 8.4V, these packs will still offer a noticeable advantage when compared to a standard 7.4V LiPo pack. Battery Model 2S HV LiPo ROAR Approved Yes  Type Silicon Graphene   Voltage 7.6V nominal  Capacity @7.4V  5000mAh  Capacity @7.6V  5400mAh  Weight  235 g  Connector Type  T-style Balance Connector  3 Pin XH Number of Cells 2 Cell  Configuration 2S1P  Dimensions (WxLxH) 46.7x137.5x24.2mm  Maximum Charge Rate 10C (50A)  Burst Current  100C  Watt Hour @7.6V  38Wh  Includes: (1) ProTek R/C Battery LITHIUM POLYMER SAFETY INFORMATION  IMPORTANT:  DO NOT leave the battery in your model when charging DO NOT leave unattended when charging  ALWAYS balance charge the battery  ALWAYS use a LiPo charging bag  YOU MUST use a Li-Poly specific charger to charge the pack (NiMH or NiCD only chargers WILL NOT WORK!)  YOU MUST not over discharge the Li-Poly battery pack READ & UNDERSTAND the instructions carefully before operating this battery  NOTE: When using high energy Li-Polymer Batteries, please do not over-discharge or over-charge batteries as this will result in over heated batteries. Discharging capacity can't exceed 80% of the max capacity of the pack after full charging to ensure a good cycle performance. It is recommended to fully charge a brand new battery before using and only discharge the battery 50% for first 5 cycles. Always monitor race time and/or set a low voltage warning on ESC (End voltage cannot be lower than 3.2v per cell). Do not use the battery that has too low a voltage. Do not expose batteries to sunshine or store/charge batteries at the temperature above 35°C or in a closed car. The high temperature environment could cause damage to the pack or make it burst. If the battery becomes hot while fast charging, high current discharging or racing, do not charge the battery until it has cooled completely. Wait about 20 mins, then inspect prior to recharging. This product was added to our catalog on April 16, 2021

Read more less

PTK-5141-22, ProTek RC 2S 50C 1100mAh Losi Mini T/B & JRX2 LiPo Battery w/EC2 Connector The Protek R/C 2S 50C 1100mAh Losi Mini T/B and JRX2 LiPo Battery is built with performance in mind. Using Silicon Graphene technology this battery packs a punch with it's 50c discharge rating! Designed to work with the Losi Mini T, B and Mini JRX2 this pack offers extended runtimes with it's larger 1100mah capacity. Equipped with an EC2 style connector makes this a plug in option with no need to mess with adapters or to get out the soldering iron. With more time on the track and the ability to dish out the power this Protek battery pack is an excellent upgrade for your Mini T, B or JRX2 vehicles. Features: Direct fit for Losi Mini B, T and JRX2 vehicles More runtime, with a dramatic increase in punch Silicone Graphene can handle more abuse and deliver more current than a standard LiPo battery Improved efficiency, lower operating temperatures, and lower internal resistance! Factory installed EC2 plug  Battery Model 2s 50C 1100mAh Application Air, Ground Type Silicon Graphene  Voltage 7.4V nominal Capacity @7.4V 1100mAh Weight 68g Connector Type EC2 Balance Connector XH Connector          Number of Cells 2 Cell Configuration 2S1P Dimensions (LxWxH) 58x32x20mm Maximum Charge Rate 4C (4.4A) Watt Hour @7.4V 8.14Wh Includes: (1) ProTek R/C Battery   This product was added to our catalog on September 1, 2022

Read more less

PTK-5115-22, ProTek RC 2S 130C Low IR Si-Graphene + HV LCG LiPo Battery (7.6V/6300mAh) w/5mm Connectors (ROAR Approved) The ProTek R/C 2S 130C Graphene + HV 6300mAh LiPo Battery is the perfect battery option for anyone looking for a lightweight and high capacity LiPo battery. Weighing only 271 grams, this 2S pack is lighter than a standard 2S pack, with much higher capacity. These advancements lead to increase in both voltage and punch throughout a run. This battery has been designed to improve power to weight ratios while maintaining a low CG. The improved efficiency of this pack will allow for lower operating temperatures and lower internal resistance. This gives users a more consistent battery pack. ProTek Graphene + 130C Packs deliver the power needed by serious racers and enthusiasts alike. Lab testing has shown that ProTek R/C Silicon Graphene packs have double the cycle life when charged at 1C rates, and can be charged at higher amp rates, with less risk of damage to the pack. More importantly, the discharge curve is flatter, meaning the cells maintain higher voltage throughout the discharge cycle with no significant drop off. Additionally, when compared to conventional LiPo batteries Silicon Graphene batteries are lighter, providing a higher capacity per gram ratio. With 7.6V nominal voltage, 130C discharge ratings, incredibly high charge rates and ten different models to choose from, ProTek R/C 130C Graphene + packs are perfect for racers and bashers that demand the absolute best. Features: Lighter than a hardcase 2S LiPo pack of equal capacity Improved power to weight ratio and a lower overall CG More runtime, with a dramatic increase in voltage and punch Silicone Graphene can handle more abuse and deliver more current than a standard LiPo battery Improved efficiency, lower operating temperatures, and lower internal resistance! Increased run time, increased cycle life and increased voltage! More capacity gram for gram when compared to standard LiPo cells Perfect for stock class racers looking to shave grams 10C max charge rates - 1C charge rate recommended for longest life 7.6V nominal voltage 5mm bullets and 5mm to 4mm bullet adapters included NOTE: While these batteries are LiHV cells, they can still be charged the same as a standard LiPo with a standard LiPo charger. The overall voltage and capacity will be slightly less than when charged to LiHV specs, but the performance will be better than a standard LiPo thanks to the flat discharge curve, reduced weight and low internal resistance. When charged to 8.4V, these packs will still offer a noticeable advantage when compared to a standard 7.4V LiPo pack. Battery Model 2S HV LiPo ROAR Approved Yes Type Silicon Graphene  Voltage 7.6V nominal Capacity @7.4V 5500mAh Capacity @7.6V 6300mAh Weight 271g Connector Type 5mm Bullet Balance Connector 2mm Bullet Number of Cells 2 Cell Configuration 2S2P Dimensions (WxLxH) 47x139x22.5mm Maximum Charge Rate 10C (61A) Burst Current 130C Watt Hour @7.6V 47.9 Wh Includes: (1) ProTek R/C Battery (2) 5mm to 4mm Bullet Reducers (2) 5mm Bullet Connectors (1) 2mm Balance Bullet Connector LITHIUM POLYMER SAFETY INFORMATION IMPORTANT: DO NOT leave the battery in your model when charging DO NOT leave unattended when charging ALWAYS balance charge the battery ALWAYS use a LiPo charging bag YOU MUST use a Li-Poly specific charger to charge the pack (NiMH or NiCD only chargers WILL NOT WORK!) YOU MUST not over discharge the Li-Poly battery pack READ & UNDERSTAND the instructions carefully before operating this battery NOTE: When using high energy Li-Polymer Batteries, please do not over-discharge or over-charge batteries as this will result in over heated batteries. Discharging capacity can't exceed 80% of the max capacity of the pack after full charging to ensure a good cycle performance. It is recommended to fully charge a brand new battery before using and only discharge the battery 50% for first 5 cycles. Always monitor race time and/or set a low voltage warning on ESC (End voltage cannot be lower than 3.2v per cell). Do not use the battery that has too low a voltage.Do not expose batteries to sunshine or store/charge batteries at the temperature above 35°C or in a closed car. The high temperature environment could cause damage to the pack or make it burst. If the battery becomes hot while fast charging, high current discharging or racing, do not charge the battery until it has cooled completely. Wait about 20 mins, then inspect prior to recharging. This product was added to our catalog on January 24, 2022

Read more less

roTek RC 2S 130C Low IR Si-Graphene + HV Shorty LiPo Battery (7.6V/6400mAh) w/5mm Connectors (ROAR Approved) The ProTek R/C 2S 130C Graphene + HV 6400mAh Shorty LiPo Battery is a great battery option for anyone looking for a lightweight, shorty style battery. Weighing only 219 grams, the HV Shorty is lighter than a standard shorty pack, with a massive increase in capacity. When compared to standard LiPo and LiHV, Silicon Graphene cells deliver improved efficiency, lower operating temperatures, lower internal resistance, better run time, increased cycle life and increased voltage. This pack is ideal pack for 2WD and 4WD modified racing, or stock class racers that want optimum voltage for the entire run. This pack is also a great choice for 1/8 e-buggies that want to run a lightweight 2x2S saddle pack configuration. The improved efficiency of this pack will allow for lower operating temperatures and lower internal resistance. This gives users a more consistent battery pack. ProTek Graphene + 130C Packs deliver the power needed by serious racers and enthusiasts alike. Lab testing has shown that ProTek R/C Silicon Graphene packs have double the cycle life when charged at 1C rates, and can be charged at higher amp rates, with less risk of damage to the pack. More importantly, the discharge curve is flatter, meaning the cells maintain higher voltage throughout the discharge cycle with no significant drop off. Additionally, when compared to conventional LiPo batteries Silicon Graphene batteries are lighter, providing a higher capacity per gram ratio. With 7.6V nominal voltage, 130C discharge ratings, incredibly high charge rates and ten different models to choose from, ProTek R/C 130C Graphene + packs are perfect for racers and bashers that demand the absolute best. Features: Lighter than a hardcase 2S LiPo pack of equal capacity More runtime, with a dramatic increase in voltage and punch Silicone Graphene can handle more abuse and deliver more current than a standard LiPo battery Improved efficiency, lower operating temperatures, and lower internal resistance! Perfect for stock class racers looking to shave grams 10C max charge rates - 1C charge rate recommended for longest life NOTE: When using high energy Li-Polymer Batteries, please do not over-discharge or over-charge batteries as this will result in overheated batteries. Discharging capacity can't exceed 80% of the max capacity of the pack after full charging to ensure a good cycle performance. It is recommended to fully charge a brand new battery before using and only discharge the battery 50% for the first 5 cycles. Always monitor race time and/or set a low voltage warning on ESC (End voltage cannot be lower than 3.2v per cell). Do not use a battery that has too low a voltage. Do not expose batteries to sunshine or store/charge batteries at temperatures above 35°C or in a closed car. The high-temperature environment could cause damage to the pack or make it burst. If the battery becomes hot while fast charging, high current discharging, or racing, do not charge it until it has cooled completely. Wait about 20 mins, then inspect prior to recharging. This product was added to our catalog on January 2, 2024

Read more less

ERC8-DC-1046, Exclusive RC Drag Racing Chute Mount "D" The Exclusive RC Drag Racing Chute Mount "D" is a mounting accessory for the Exclusive RC Drag Racing Parachute (EXC-ERC-8-DC-1035). This two piece chute mount features an upper chute mount and a separate rope mount that have been 3D printed from super strong carbon nylon filament, and the mount design will allow fitment with various body types. Mount measures 29.56x26.60x25.91mm (upper) and 20.00x11.24x8.58mm (Rope Mount) and stainless steel hardware is included for mounting and adjustments. Chute Mount Measurements (LxWxH): Chute A: 42.27x25.87x61.57mm (Universal) Chute B: 29.28x26.01x55.13mm (Universal) Chute C (Double): 29.28x60.22x55.58mm (Universal) Chute D: 29.56x26.60x25.91mm (upper); 20.00x11.24x8.58mm (Rope Mount) (Universal Fit) Chute E: 29.28x26.01x43.81mm (Universal) Chute F (Double): 35.42x62.51x43.41mm (Pro-Line 69 NOVA) Chute G: 37.35x26.10x43.41 (Pro-Line 69 NOVA)  This product was added to our catalog on February 10 ,2024

Read more less

PTK-5188, ProTek RC LiFe Futaba Transmitter Battery Pack (6.6V/2100mAh) (3PV/4PK/4PM/4PLS/4PX/4PV/7PX/7PXR/10PX/16SZ) This is the ProTek R/C LiFe Car Transmitter Battery Pack, and is intended for use with the Futaba 3PV, 4PK, 4PM, 4PV, 4PLS, 4PX, 7PX, 10PX, 16SZ, and 18SZ Transmitters. Lithium battery technology is evolving. With cell dimensions that fit anywhere a standard Li-Po battery will and rapidly increasing capacity, LiFe chemistry will soon set the standard that all others are judged by. With the ability to deliver 1000+ usable cycles, and a life span up to 4 times longer than Li-Poly batteries (when cycled under the same discharge conditions), these batteries offer the user an excellent balance of performance and value. LiFe batteries are more durable than Li-Poly and are able to handle a higher level of abuse when compared to Li-Poly without the risk of pre-mature failure. Unlike Li-Poly, LiFe cells can be stored in a fully charged state with little to no loss in stored power, and can be discharged deeper with less risk of damage to the cells. Most importantly, LiFe batteries are SAFE! There is no risk of combustion! LiFe cells will not catch fire or explode when over charged, or after a deep discharge. What about the voltage? A 2 Cell LiFe battery produces 6.6 volts nominal, which is almost a full volt less than a 2 Cell LiPo battery. The LiFe battery is not meant to replace the performance of a Li-Po battery, it is simply another option. LiFe offers the user a battery with a good discharge curve that is better than that of a NiMH battery, but without the risk of damage or fire that exists when a LiPo battery is abused. NOTE: Brand new LiFePO4 batteries have been found to fail prematurely if they are deep discharged below below 33% capacity too early. A break-in period of 20 cycles is currently recommended. While testing has shown that this battery can be charged at up to 3C rates, it is recommended that this battery not be charged at rates higher than 1C to maximize the lifespan of the battery. Additionally, LiFe batteries should not be discharged below 2.5V per cell to avoid pre-mature failure and maximize battery life span. We also recommend you REMOVE the batteries from your cars or radios when you are done, or at least unplug them to avoid accidental over discharge if the unit is left on. Features: Safe chemistry will not explode or catch fire More mAh per gram compared to NiMH cells, meaning lighter models, and longer runtime Virtually no "self discharge", so the battery is always ready to go even weeks after charging. Superior voltage performance under load compared to NiMH cells, with consistent torque and speed. Fast charge time Specifications: Voltage: 6.6V Capacity: 2100mah Chemistry: LiFePO4 Balance Charge Plug: XH Charge Rate: 1C Compatibility: Futaba 3PV, 4PK, 4PM, 4PV, 4PLS, 4PX, 7PX, 10PX, 16SZ, and 18SZ Discharge Plug: JR/Futaba Dimension (LxWxH): 76x41x17mm Weight: 105g This product was added to our catalog on December 16, 2021

Read more less

ERC8-DC-1035, Exclusive RC Non Functional Drag Racing Parachute (Black) The Exclusive RC Non Functional Drag Racing Parachute is an accurately scaled down replica of a 1:1 drag racing parachute. Manufactured with real chute bag material, and an included chute tag, this is a great way to finish off the back end of your street eliminator/no prep car. Available in multiple colors. Installation requires the Exclusive RC Drag Chute Mount (not included). A variety of mounts are available to mount various body types and styles.  Specifications:Dimensions:Length: 30mmWidth: 30mmHeight: 30mm This product was added to our catalog on February 2,2024

Read more less