Hot Racing
Hot Racing HRASTE886, Hot Racing Traxxas 48P Hardened Steel Spur Gear (86T)
HRASTE886, Hot Racing Traxxas 48P Hardened Steel Spur Gear (86T) This product was added to our catalog on December 16, 2021
$19.99
Hot Racing HRAERVT46M01, Hot Racing E Revo 2.0/X-Maxx/XO-1 Steel Mod 1 Steel Spur Gear (46T)
HRAERVT46M01, Hot Racing E Revo 2.0/X-Maxx/XO-1 Steel Mod 1 Steel Spur Gear (46T) Traxxas E-Revo VXL 2.0 Traxxas Maxx Traxxas X-Maxx Traxxas XO-1 Traxxas XRT The Hot Racing hardened steel Mod 1 spur gear is an optional upgrade for the Traxxas E Revo 2.0, X-Maxx 6S and 8S, Maxx 4S and XO-1 models. Choose from 50, 52 and 54 tooth options. NOTE: Do NOT use the pin system for setting the X-Maxx gear mesh. Instead, manually set the gear mesh without the pins. Refer to the Traxxas manual for instructions (ref. pg.22 Adjusting Gear Mesh) With the pins removed, use the four 4x16mm button-head cap screws on the bottom to set gear mesh. Loosen the four 4x16mm button-head cap screws. Cut a narrow strip of notebook paper and run it into the gear mesh. Slide the motor and pinion gear into the spur gear. Tighten the four 4x16mm button-head cap screws, and then remove the strip of paper. You should be able to run a fresh strip of paper through the gears without binding them. Features: CNC machined hardened steel construction Black oxide finished Laser etched tooth count marking Upgrade for factory plastic spur gear Specifications: Overall diameter: 52.8mm Gear face width: 8mm Includes: One (1) mod 1 steel spur gear This product was added to our catalog on December 16, 2021
$30.99
Hot Racing HRASJT254, Hot Racing Traxxas 32P Steel Spur Gear (Silver) (54T)
HRASJT254, Hot Racing Traxxas 32P Steel Spur Gear (Silver) (54T) This is the Hot Racing Steel 32 Pitch, 54 Tooth Spur Gear with Silver hardware for the 1/10 Traxxas E-Revo, Jato 3.3, T-Maxx 3.3, T-Maxx 2.5R, Summit, Rally VXL, Slash 4X4, and Stampede 4X4. Features: CNC machined and lightened hardened steel construction Black oxide coating for durability and corrosion resistance Silver-colored countersunk washers Specifications: Number of Teeth: 54 Gear Pitch: 32 pitch (0.8 module) Mounting Holes: 3 Tooth Face width: 6mm (0.24 inch) Internal diameter: ~11mm (~0.43 inch) Includes: 54 tooth 32 pitch spur gear (3) mounting screws (3) silver-colored countersunk washers (3) washers (use as needed underneath countersunk washers to prevent screw ends from protruding too far through spur mounting plate) Requires: Hardened clutch bell or pinon gear Requires a slipper transmission. Will NOT work with vehicle equipped with a center gear differential. Use Hot Racing SSLF2 series gears for vehicles equipped with a center gear differential. This product was added to our catalog on May 16, 2021
$20.99
Hot Racing HRASTE876, Hot Racing Traxxas 48P Hardened Steel Spur Gear (76T)
HRASTE876, Hot Racing Traxxas 48P Hardened Steel Spur Gear (76T) Compatibility Traxxas Bandit Traxxas Rustler 2wd Traxxas Slash 2wd Traxxas Stampede 2wd Traxxas Telluride 4x4 The Hot Racing Traxxas 48P Hardened Steel Spur Gear is an optional spur gear intended for the Traxxas Bandit, 2WD Slash, Rustler, 2WD Stampede, and Telluride models. The spur gear is available in a variety of tooth count options, please select the specific gear you want from the list above. Package includes one spur gear and mounting hardware.NOTE: Motor temperature should never exceed 180F (under 160 recommended). ESC temperatures should never exceed 160F. Excessive temperatures will shorten the life of the electronics. Features: CNC machined and lightened hardened steel construction Replaces stock nylon spur gear Black oxide coated gear for durability and corrosion resistance Red anodized countersunk aluminum washers High strength hardware Specifications: Gear Pitch: 48 pitch Mounting Holes: 3 Tooth Face width: ~5mm This product was added to our catalog on February 21, 2022
$19.99
Hot Racing HRASTE288RC, Hot Racing Traxxas Slash Rear Light Weight CV Splined Drive Shaft (2)
HRASTE288RC, Hot Racing Traxxas Slash Rear Light Weight CV Splined Drive Shaft (2) This is a set of Hot Racing Traxxas Slash Rear Light Weight CV Splined Drive Shafts, intended for use with the Traxxas electric Stampede and Rustler models. This is an optional upgrade heavy duty splined star drive axle kit. Features: CNC machined #45 hardened carbon steel, S2 spring steel and Aluminum construction Replaces factory plastic drive axles Hard Black Anodized Aluminum Slider Blue anodized aluminum pin capture rings with rubber o-rings to prevent movement Design eliminated CV pin setscrew Hardened S2 Spring steel wheel shaft #45 Steel is black finish S2 spring in Brown finish Rubber dust boot to keep the Splined Drive for maximum protection against the elements Replaces Traxxas TRA1951 half shafts, TRA2753X stub axles, and TRA4628 output yokes Specifications: Approximate overall collapsed length: 109mm Includes: (2) Rear Cv Splined Drive Shaft spline CVD shaft assemblies (2) M4x2.5x11mm screw shafts Fits: Traxxas Rustler 2wd Traxxas Stampede 2wd This product was added to our catalog on December 16, 2021
$54.99
Hot Racing HRAERVT54M01, Hot Racing E Revo 2.0/X-Maxx/XO-1 Steel Mod 1 Steel Spur Gear (54T)
HRAERVT54M01, Hot Racing E Revo 2.0/X-Maxx/XO-1 Steel Mod 1 Steel Spur Gear (54T) Traxxas E-Revo VXL 2.0 Traxxas Maxx Traxxas X-Maxx Traxxas XO-1 Traxxas XRT This product was added to our catalog on December 16, 2021
$30.99
Hot Racing HRATRX15EPL06, Hot Racing Traxxas Slash 4x4 Power Up Gear Adapter (Short)
HRATRX15EPL06, Hot Racing Traxxas Slash 4x4 Power Up Gear Adapter (Short) Fits: Traxxas E-Maxx Traxxas E-Revo Traxxas Rally Traxxas Revo Nitro Traxxas Slash 4x4 Traxxas Slayer Traxxas Stampede 4x4 Traxxas Summit 1/10 Traxxas T-Maxx This product was added to our catalog on May 16, 2021
$16.99
Hot Racing HRASLTN60M5, Hot Racing LaTrax Rally/SS Steel 0.5 Mod Main Gear (60T)
HRASLTN60M5, Hot Racing LaTrax Rally/SS Steel 0.5 Mod Main Gear (60T) This product was added to our catalog on December 16, 2021
$16.99
Hot Racing HRATRXM10H15, Hot Racing Traxxas TRX-4M 7mm Brass Wheel Hexes w/Pins (4) (+1.5mm) (1.5g)
HRATRXM10H15, Hot Racing Traxxas TRX-4M 7mm Brass Wheel Hexes w/Pins (4) (+1.5mm) (1.5g) Hot Racing Traxxas TRX-4M 7mm Brass Wheel Hexes with Pins. These optional wheel hexes are intended for the Traxxas TRX-4M. Made from CNC Machined brass, these are designed to lower the CG and increase track width for better stability and tire clearance. Package includes four wheel hexes and four axle pins.Features: Direct fit to the TRX-4M Made from CNC Machined brass Fits standard 3.5mm axle shafts Increases tire clearance to body and chassis This product was added to our catalog on February 1, 2023
$11.99
Hot Racing HRASJT253, Hot Racing Traxxas 32P Steel Spur Gear (Grey) (53T)
HRASJT253, Hot Racing Traxxas 32P Steel Spur Gear (Grey) (53T) This is the Hot Racing Steel 32 Pitch, 53 Tooth Spur Gear with grey hardware for the 1/10 Traxxas E-Revo, Jato 3.3, T-Maxx 3.3, T-Maxx 2.5R, Summit, Rally VXL, Slash 4X4, and Stampede 4X4. Features: CNC machined and lightened hardened steel construction Black oxide coating for durability and corrosion resistance Grey-colored countersunk washers Specifications: Number of Teeth: 53 Gear Pitch: 32 pitch (0.8 module) Mounting Holes: 3 Tooth Face width: 6mm (0.24 inch) Internal diameter: ~11mm (~0.43 inch) Includes: 54 tooth 32 pitch spur gear (3) mounting screws (3) grey-colored countersunk washers (3) washers (use as needed underneath countersunk washers to prevent screw ends from protruding too far through spur mounting plate) Requires: Hardened clutch bell or pinon gear Requires a slipper transmission. Will NOT work with vehicle equipped with a center gear differential. Use Hot Racing SSLF2 series gears for vehicles equipped with a center gear differential. This product was added to our catalog on December 16, 2021
$23.99
Hot Racing HRAERVT52M01, Hot Racing E Revo 2.0/X-Maxx/XO-1 Steel Mod 1 Steel Spur Gear (52T)
HRAERVT52M01, Hot Racing E Revo 2.0/X-Maxx/XO-1 Steel Mod 1 Steel Spur Gear (52T) This product was added to our catalog on December 16, 2021
$30.99
Hot Racing HRASLF288RCR, Hot Racing Slash 4x4 Rear Light Weight Metal CV Splined Drive Shaft Set
HRASLF288RCR, Hot Racing Slash 4x4 Rear Light Weight Metal CV Splined Drive Shaft Set Traxxas Rustler 4x4 Traxxas Slash 2wd Traxxas Slash 4x4 Traxxas Stampede 4x4 This is a replacement Hot Racing Slash Rear Light Weight Metal CV Splined Drive Shaft Set for the Slash, Slash 4X4, Stampede 4X4 and Rustler 4X4. Features: CNC machined #45 hardened carbon steel, S2 spring steel and Aluminum construction Replaces factory plastic drive axles Hard Black Anodized Aluminum Slider Blue anodized aluminum pin capture rings with rubber o-rings to prevent movement Design eliminated CV pin setscrew Hardened S2 Spring steel wheel shaft #45 Steel is black finish S2 spring in Brown finish Rubber dust boot to keep the Splined Drive for maximum protection against the elements Includes: (2) Rear Cv Splined Drive Shaft spline CVD shaft assemblies (2) M4x2.5x11mm screw shafts Specifications:Approximate overall collapsed length: 113mm NOTES: Replaces factory plastic Traxxas parts Replacement parts include: SLD425 (M4x2.5x11mm screw shafts) This product was added to our catalog on December 16, 2021
$54.99
Hot Racing HRASPN311AR06, Hot Racing Traxxas Spartan Aluminum Adjustable Trim Tab Set (Blue)
HRASPN311AR06, Hot Racing Traxxas Spartan Aluminum Adjustable Trim Tab Set (Blue) Hot Racing Traxxas Spartan Aluminum Adjustable Trim Tab Set. Features: Adjusts angle of trim tab assembly for proper hull planing CNC machined aluminum construction Pre-drilled for mounting Anodized blue for durability, corrosion resistance, and great looks Specifications: Weight: 0.78oz length: 33mm (1.30 inches) width: 30mm (1.18 inches) height: 24.5mm (.96 inches) NOTE: Use the stock 4x12mm screws to mount This product was added to our catalog on December 16, 2021
$39.99
Hot Racing HRASLF288RCF, Hot Racing Traxxas Slash 4x4 Front Light Weight Metal CV Splined Drive Shaft
HRASLF288RCF, Hot Racing Traxxas Slash 4x4 Front Light Weight Metal CV Splined Drive Shaft This is a set of Hot Racing Traxxas Slash 4x4 Light Weight Front Metal CV Splined Drive Shafts, an optional upgrade heavy duty splined star drive axle kit for the Traxxas electric Stampede 4X4, Slash 4x4, Rustler 4X4 models. Features: CNC machined #45 hardened carbon steel, S2 spring steel and Aluminum construction Replaces factory plastic drive axles Hard Black Anodized Aluminum Slider Blue anodized aluminum pin capture rings with rubber o-rings to prevent movement Design eliminated CV pin setscrew Hardened S2 Spring steel wheel shaft #45 Steel is black finish S2 spring in Brown finish Rubber dust boot to keep the Splined Drive for maximum protection against the elements Replaces factory plastic Traxxas parts Specifications: Approximate overall collapsed length: 112mm Includes: (2) Front Cv Splined Drive Shaft spline CVD shaft assemblies (2) M4x2.5x11mm screw shafts This product was added to our catalog on December 16, 2021
$55.99
Hot Racing STRXM39W05, Hot Racing Traxxas TRX-4M +5mm Front & Rear Hardened Steel Drive Axles
STRXM39W05, Hot Racing Traxxas TRX-4M +5mm Front & Rear Hardened Steel Drive Axles Hot Racing Traxxas Traxxas TRX-4M +5mm Front & Rear Hardened Steel Drive Axles. These high quality axles are an excellent addition to the Traxxas TRX-4M rock crawler giving you an additional 5mm of width per side. Constructed from high strength hardened steel, the axles are built to handle demanding situations and offer superior performance over the stock components. Features: Increases width of vehicle by 5mm on each side Increases stability Increases steering clearance Increases tire options CNC machined hardened steel axle Aluminum +5mm spacer (anodized) Upgrades stock axles or provides a replacement for worn or damaged shafts Fits front and rear Includes: (2) +5mm Front Stub Axles (2) +5mm Rear Drive Axles (4) Axle Spacers This product was added to our catalog on February 7, 2023
$19.99
Hot Racing HRASLF311, Hot Racing Traxxas Slash 4x4 Front & Rear Sway Bar
HRASLF311, Hot Racing Traxxas Slash 4x4 Front & Rear Sway Bar This product was added to our catalog on December 16, 2021
$26.99
Hot Racing HRASTE872, Hot Racing Traxxas 48P Hardened Steel Spur Gear (72T)
HRASTE872, Hot Racing Traxxas 48P Hardened Steel Spur Gear (72T) This product was added to our catalog on December 16, 2021
$19.99
Hot Racing HRATRXM19H, Hot Racing Traxxas TRX-4M Brass C-Hubs (2) (7.5g)
HRATRXM19H, Hot Racing Traxxas TRX-4M Brass C-Hubs (2) (7.5g) Hot Racing Traxxas TRX-4M Brass C-Hubs. These optional CNC machined brass C-hubs offer increased weight and durability over the stock components. Constructed from brass material these lower the center of gravity and improve the crawling performance of the Traxxas TRX-4M while adding a custom look to your crawler. NOTE: Hot Racing recommends the use of bearings over the stock bushings on the TRX-4M for optimum performance. Features: CNC machined Brass Adds 7.5g of weight per hub over stock Direct replacement for stock components Includes: (1) Left Brass C-Hub (1) Right Brass C-Hub (4) Brass Kingpin Bushings (4) Mounting Screws This product was added to our catalog on February 7, 2023
$23.99
Hot Racing HRASSLG52M1, Traxxas Sledge Steel Spur Gear (52T 1 Mod)
HRASSLG52M1, Traxxas Sledge Steel Spur Gear (52T 1 Mod) This product was added to our catalog on October 20, 2022
$39.99
Hot Racing HRATRXM21H, Hot Racing Traxxas TRX-4M Brass Steering Knuckle (2) (19.4g) (For Bearing Use)
HRATRXM21H, Hot Racing Traxxas TRX-4M Brass Steering Knuckle (2) (19.4g) (For Bearing Use) Hot Racing Traxxas TRX-4M Brass Steering Knuckle. These steering knuckles are intended for the Traxxas TRX-4M, when equipped with the optional bearing kit. Made from CNC Machined brass, these help to lower the Center of Gravity (CG) to help keep your truck planted. Package includes two brass steering knuckles. NOTE: Due to the tight tolerances for bearings, factory bushings may not fit. Features: Made from CNC Machined brass Lowers CG to increase stability and front weight bias This product was added to our catalog on February 1, 2023
$28.99
Hot Racing HRASPN56TF06, Hot Racing Traxxas Spartan Aluminum Adjustable Turn Fins
HRASPN56TF06, Hot Racing Traxxas Spartan Aluminum Adjustable Turn Fins Hot Racing Traxxas Spartan Aluminum Adjustable Turn Fins will help your boat turn faster, provide better straight-line handling, and will increase overall stability. Features: Increases performance and handling CNC machined aluminum construction Blue anodized finish Easy to install Light weight Adjustable Includes: (2) aluminum turn fins (2) aluminum turn fin mounting brackets (2) 3mm lock nuts (2) socket head cap screws This product was added to our catalog on March 16, 2021
$29.99
Hot Racing HRASLF25SH06, Hot Racing Traxxas Slash/Stampede 4x4 Aluminum Lock Servo Arm (25T)
HRASLF25SH06, Hot Racing Traxxas Slash/Stampede 4x4 Aluminum Lock Servo Arm (25T)This product was added to our catalog on December 16, 2021
$10.99
Hot Racing HRASTE256, Hot Racing Traxxas 32P Steel Pinion & Spur Gear Set (Purple) (18T/56T) (Slash, Rustler, Stampede, Bandit)
HRASTE256, Hot Racing Traxxas 32P Steel Pinion & Spur Gear Set (Purple) (18T/56T) Hot Racing Traxxas 32P Steel Pinion & Spur Gear Set (Purple) (18T/56T) (Slash, Rustler, Stampede, Bandit) This is an optional Hot Racing 32 Pitch Steel Pinion and Spur Gear Set for use with the following Traxxas 2WD models: Bandit, Rustler, Slash and Stampede. Features: CNC machined and lightened hardened steel construction Replaces stock nylon spur gear Rugged 0.8 Module/32pitch teeth for total reliability on brushless power Aluminum pinion sleeve to allow for either 1/8 inch or 5mm motor shafts Black oxide coated gear for durability and corrosion resistance Purple anodized countersunk aluminum washers High strength hardware Specifications: Number of Teeth: 18T/56T Gear Pitch: 32 pitch (0.8 module) Mounting Holes: 3 Tooth Face width: ~5mm Includes: (1) 18 tooth 32 pitch (0.8 Mod) pinion gear (1) 56 tooth 32 pitch (0.8 Mod) spur gear (3) mounting screws (3) purple anodized countersunk washers (1) pinion adapter sleeve (3) washers (use as needed underneath countersunk washers to prevent screw ends from protruding too far through spur backing plate) This product was added to our catalog on March 16, 2021
$25.99
Hot Racing HRATRXF03EMR01, Hot Racing Traxxas TRX-4 Aluminum Front Bumper w/Winch Mount & Light Buckets
HRATRXF03EMR01, Hot Racing Traxxas TRX-4 Aluminum Front Bumper w/Winch Mount & Light Buckets This product was added to our catalog on December 16, 2021
$49.99
Hot Racing HRAXMX48M06, Hot Racing Traxxas X-Maxx Aluminum Steering Servo Saver Bellcrank
HRAXMX48M06, Hot Racing Traxxas X-Maxx Aluminum Steering Servo Saver Bellcrank The Hot Racing Aluminum Steering Servo Saver Bellcrank is an adjustable aluminum steering bellcrank and servo saver for the Traxxas X-Maxx. Features: Super-tough, fully adjustable servo saver bell crank Replaces factory plastic for a stronger-than-standard stock steering system CNC machined aluminum construction Reuses factory ball bearings for smooth operation Retains stock double shear design for ultimate reliability Adjustable servo saver springs for different tension Two servo saver springs to suit preference. Black (installed) is same as stock Traxxas, silver is stiffer then stock Anodized blue and black for durability, corrosion resistance, and aesthetics Includes: (1) assembled steering bellcrank (1) aluminum draglink (1) silver hard stiffness servo saver spring (1) black medium stiffness servo saver spring NOTE: Requires use of the stock bearings and some of the stock hardware Recommended to use removable-type thread lock on any screws threading into metal Optional use of a grease lubricant on servo saver cam surfaces can smooth servo saver action and prolong life Replaces most of Traxxas TRA7746 steering components Replacement Hot Racing draglink is part number HRAXMX4906 Aluminum servo horn is Hot Racing HRAXMX48A06 This product was added to our catalog on September 6, 2021
$70.99
Hot Racing HRASLG156AX01, Aluminum bleeder shock caps Traxxas Sledge
HRASLG156AX01, Aluminum bleeder shock caps Traxxas Sledge This product was added to our catalog on December 1, 2022
$23.99
Hot Racing HRASTE282RP, Hot Racing Traxxas Slash Steel CV Drive Shafts
HRASTE282RP, Hot Racing Traxxas Slash Steel CV Drive Shafts The Hot Racing Traxxas Slash Steel CV Drive Shafts are an excellent way to increase the reliability of your Traxxas Slash 2wd. Made with high strength steel these shafts offer higher strength over the stock plastic shafts along with smoother operation due to the CV (constant velocity) joint. Package includes two assembled steel CV drive shafts and two differential drive cups. This product was added to our catalog on May 16, 2021
$36.99
Hot Racing HRATUDR37R, Steel Rear Drive Shaft for UDR
Steel Rear Drive Shaft for UDR
$29.99
Hot Racing HRARVO5095, Hot Racing High Lift Shock Springs, Chrome 15lb/in, 2pcs, for Traxxas GTR Shocks
HRARVO5095, Hot Racing High Lift Shock Springs, Chrome 15lb/in, 2pcs, for Traxxas GTR Shocks Hot Racing extra-lift cold-coiled shock springs for the Traxxas E-Revo, Revo 3.3, Slayer Pro 4X4, and Summit. These springs are approximately 5mm longer than the stock springs to help compensate and raise the vehicle after adding heavy duty upgrades or high capacity batteries. Adding these springs will add 5 to 10 percent more ground clearance to the vehicle, depending on the vehicle components installed. This product was added to our catalog on December 16, 2021
$6.99
Hot Racing HRATUDR88SLS108, Hot Racing 108mm Traxxas Unlimited Desert Racer Rear Suspension Travel Limit Strap (2)
HRATUDR88SLS108, Hot Racing 108mm Traxxas Unlimited Desert Racer Rear Suspension Travel Limit Strap (2) This is a pack of two optional Hot Racing 108mm Rear Suspension Travel Limit Strap intended for use with the Traxxas UDR. Hot Racing scale functional suspension limit straps limit suspension travel for Traxxas UDR Limit straps are used to take stress off shocks and to control suspension extension. when crawling up or descending steep grades, straps tied to the center of an axle are useful to limit the suspension from unloading and the vehicle from rolling, all while keeping suspension articulation intact. From climbing, to droop control, to super scale looks, these limit straps will get you further and get you noticed! Features: Woven 2-ply Nylon fabric strap material CNC machined aluminum clevis buckles, anodized Red in color Specifications: Eyelet hole size: 3.3mm (0.13 inch) - for a 3mm screw NOTES: These straps are made from 200 lb. test nylon and offers minimal stretch to provide a consistent strap length and to protect against overextending shocks Tested on extreme off-road terrain Strap lengths are measured from the center of the mounting holes and are accurate to +/- 3mm This is the replacement of TRA8548 This product was added to our catalog on December 16, 2021
$16.99
Hot Racing HRASPN1000ME, Hot Racing Traxxas Spartan/M41 Pro Brass Prop w/Nut & Drive Dog (Brass/Blue)
HRASPN1000ME, Hot Racing Traxxas Spartan/M41 Pro Brass Prop w/Nut & Drive Dog (Brass/Blue) This is an optional Hot Racing 42x63mm Polished Brass Propeller, intended for use with the Traxxas DCB M41 and Spartan boats as a replacement for the stock plastic part. This part has been machined out of polished brass and includes an aluminum conical M4 propeller nut and drive dog, both anodized blue for added strength and style. Features: CNC machined from polished brass Anodized blue CNC machined Aluminum conical prop nut and drive dog Replaces factory plastic propeller Replaces factory hex nut with hydro dynamically efficient conical nut for reduced drag Specifications: Prop diameter: 42mm (1.65 inches) Prop pitch: 63mm (2.48 inches) Weight: 9g (0.32 oz) Prop nut length: 18.3mm (0.72 inch) Prop nut diameter: 8mm (0.31 inch) Includes: (1) CNC brass prop (1) Aluminum bullet prop nut (1) Aluminum drive dog (1) stainless steel setscrew This product was added to our catalog on July 23, 2021
$55.99
Hot Racing HRASSLG889D, Mod 1 SS Motor Fix Mount Washer Sledge
Mod 1 SS Motor Fix Mount Washer Sledge
$9.99
Hot Racing HRAMXX288RC06, Hot Racing Traxxas Maxx Metal CV Splined Drive Shaft (Blue) (2)
HRAMXX288RC06, Hot Racing Traxxas Maxx Metal CV Splined Drive Shaft (Blue) (2) The Hot Racing Traxxas Maxx Metal CV Splined Drive Shaft is an optional heavy duty splined star drive CVD axle kit that fits the front or rear of the Traxxas 1/10th scale Maxx monster truck. NOTE: Traxxas WIDE Maxx applications require optional 65mm center drive tube (HRASLD65T) Must re-use the stock Drive pin and set screw Pin Maintain CV joint and shaft spline with grease Use medium thread lock on screws threading into metal Features: CNC machined #45 hardened carbon steel CVs, drive hub, male slider spline, and stub axle CNC machined aluminum slider tube Blue anodized aluminum pin capture rings with rubber o-rings to prevent movement Rubber dust cover boots Replaces factory front or rear driveshaft axles Specifications: Collapsed length (overall): 140mm Extended length (overall resulting in zero shaft engagement): 156mm Collapsed length (wheel pin to outdrive pin): 118mm Extended length (wheel pin to outdrive pin resulting in zero shaft engagement): 132mm Includes: (2) splined axle assemblies This product was added to our catalog on December 16, 2021
$70.99
Hot Racing HRATUDR288RC, Hot Racing Unlimited Desert Racer Front Steel CV Splined Drive Shaft (2)
HRATUDR288RC, Hot Racing Unlimited Desert Racer Front Steel CV Splined Drive Shaft (2) This is a pack of two optional Hot Racing Front Steel CV Splined Drive Shafts for the Traxxas UDR. Hot Racing optional upgrade heavy duty front splined star drive CVD axle kit for the Traxxas Unlimited Desert Racer. Features: Completely replaces factory dogbone-style axles from the differential all the way out to the wheel hex CNC machined #45 hardened carbon steel CVs, drive hub, male slider spline, and stub axle CNC machined aluminum slider tube Blue anodized aluminum pin capture rings with rubber o-rings to prevent movement Specifications: Collapsed length, overall: 154mm Extended length, overall resulting in zero shaft engagement: 164mm Collapsed length, wheel pin to outdrive pin: 138mm Extended length, wheel pin to outdrive pin resulting in zero shaft engagement: 148mm Weight/pr: 132g Needed To Complete: Installation to drive assembly Reuses drive pins Recommended to maintain CV joint and shaft spline with grease Recommended to medium thread lock on screws threading into metal NOTES: Replaces Traxxas axle parts: TRA8551 (drive cup & screw), TRA8550 (dogbone), TRA8553 (stub axle), TRA8554 (CV joint) This product was added to our catalog on December 16, 2021
$70.99
Hot Racing HRATRXM2401, Hot Racing Traxxas TRX-4M Aluminum Servo Mount (Black)
HRATRXM2401, Hot Racing Traxxas TRX-4M Aluminum Servo Mount (Black) Hot Racing Traxxas TRX-4M Aluminum Servo Mount. This optional servo mount uses CNC machined aluminum to provide a solid servo mounting solution for the Traxxas TRX-4M rock crawler. Using aluminum construction keeps this mount from flexing under high loads unlike the stock plastic mount. This mount is an easy upgrade giving your rig precise and consistent steering performance. Features: CNC machined 6061-T6 billet aluminum Secure servo mount over stock plastic mount Installs easily with no modifications Includes: (1) Traxxas TRX-4M Aluminum Servo Mount (2) Mounting Screws This product was added to our catalog on February 7, 2023
$14.99
Hot Racing HRASSLG889A, 1.5 Mod 11:34 SS Motor Fix Mount Washer Sledge
1.5 Mod 11:34 SS Motor Fix Mount Washer Sledge
$9.99
Hot Racing HRASSLG889B, Traxxas Sledge 1.5 Mod 13:34 SS Motor Fix Mount Washer
HRASSLG889B, Traxxas Sledge 1.5 Mod 13:34 SS Motor Fix Mount Washer This product was added to our catalog or updated on April 4, 2022
$9.99
Hot Racing HRASSLG889C, Traxxas Sledge Mod 1.5 and Mod 1 SS Motor Fix Mount Washer
HRASSLG889C, Traxxas Sledge Mod 1.5 and Mod 1 SS Motor Fix Mount Washer This product was added to our catalog or updated on April 4, 2022
$9.99
Hot Racing HRAERVT331F01, Hot Racing Traxxas E-Revo 2.0 Aluminum Front Skid Plate
Hot Racing Traxxas E-Revo 2.0 Aluminum Front Skid Plate. Package includes optional aluminum front skid plate for the Traxxas E-Revo 2.0. Features: Solid Billet aluminum construction incorporating CNC machined 6061-T6 aluminum construction Anodized black with Hot Racing logo and secondary processed machined edges for outstanding aesthetics Replaces part of Traxxas TRA8637 Includes: (1) front skid plate set Installation hardware This product was added to our catalog on December 16, 2021
$40.99
Hot Racing HRAXMX12C01, Hot Racing Traxxas X-Maxx Aluminum Gearbox Cover (Black)
HRAXMX12C01, Hot Racing Traxxas X-Maxx Aluminum Gearbox Cover (Black) This product was added to our catalog on May 16, 2021
$49.99
Hot Racing HRASTE873, Hot Racing Traxxas 48P Hardened Steel Spur Gear (73T)
HRASTE873, Hot Racing Traxxas 48P Hardened Steel Spur Gear (73T) The Hot Racing Traxxas 48P Hardened Steel Spur Gear is an optional spur gear intended for the Traxxas Bandit, 2WD Slash, Rustler, 2WD Stampede, and Telluride models. The spur gear is available in a variety of tooth count options, please select the specific gear you want from the list above. Package includes one spur gear and mounting hardware. NOTE: Motor temperature should never exceed 180F (under 160 recommended). ESC temperatures should never exceed 160F. Excessive temperatures will shorten the life of the electronics. Features: CNC machined and lightened hardened steel construction Replaces stock nylon spur gear Black oxide coated gear for durability and corrosion resistance Red anodized countersunk aluminum washers High strength hardware Specifications: Gear Pitch: 48 pitch Mounting Holes: 3 Tooth Face width: ~5mm This product was added to our catalog on May 16, 2021
$19.99
Hot Racing HRATE311PR, Hot Racing Traxxas Slash Sway Bar Push Rod (Blue) (2)
HRATE311PR, Hot Racing Traxxas Slash Sway Bar Push Rod (Blue) (2) The Hot Racing Traxxas Slash Sway Bar Push Rod set is a replacement for Traxxas Slash 2wd trucks equipped with the Hot Racing HRATE311SLC sway bar kit. Features: Nylon rod ends Blue anodized center aluminum spacer Aluminum pivot balls on one side, steel pivot ball stud on the other Use with Hot Racing HRATE311SLC Sway Bar Specifications: Overall length: 43mm Length on centers: 32.5mm This product was added to our catalog on December 16, 2021
$12.99
Hot Racing HRASPN48DR06, Hot Racing Traxxas Spartan Aluminum Dual Pickup Rudder Blade
HRASPN48DR06, Hot Racing Traxxas Spartan Aluminum Dual Pickup Rudder Blade This is the optional Hot Racing Aluminum Dual Pickup Rudder Blade for use with the Traxxas Spartan Boat. Features: CNC machined billet aluminum construction Dual water pickup for additional cooling Blue anodized finish for durability, corrosion resistance, and great looks Direct installation with no modification necessary Specifications: Width of top of rudder blade: 30.8mm (1.21 inches) Width of bottom of rudder blade: 25.3mm (1.00 inches) Total rudder length: 100mm (3.94 inches) Requires: Adding a second water line and a water outlet Installing and attaching linkage, water line, and dual water outlet Comments: Replaces Traxxas factory TRA5740 rudder blade For ultimate cooling, combine with Hot Racing SPN36WC01 CNC milled aluminum cooling jacket and SPN28WE06 dual port cooling outlet This product was added to our catalog on March 16, 2021
$29.99
Hot Racing HRASRVO1025, Hot Racing Traxxas Locker Spool Differential
HRASRVO1025, Hot Racing Traxxas Locker Spool Differential This is the Hot Racing Traxxas Locker Spool Differential for use with an Traxxas model that uses the TRA5381 differential; including, but not limited to, the E-Maxx, E-Revo, Revo 3.3, Slayer Pro 4X4, and T-Maxx 3.3. Traxxas E-Revo Traxxas Revo Nitro Traxxas Slayer Traxxas T-Maxx Features: Steel shaft and 6061 aluminum gear hub construction Steel shaft is black oxide finished Aluminum hub is blue anodized The locker/spool eliminates differential action for greater acceleration and climbing. It is recommended for off-road use only. Specifications: Output shaft diameter: 6mm Overall length: 45mm Driveshaft screw pin thru hole: 2.5mm Weight w/o screws: 16g Requires: Recommended to use a removable-type locking adhesive on screws threading into metal Check hub setscrew for proper torque prior to installation Ring and pinion gears and factory Traxxas TRA5380/TRA3979 differential housing, TRA5118 8x16x5mm bearing, and TRA5119 10x15x4mm bearing This product was added to our catalog on December 16, 2021
$9.99
Hot Racing HRATRF2201, Hot Racing Aluminum Traxxas 4-Tec 2.0 Rear Hub Carriers (Black) (2)
HRATRF2201, Hot Racing Aluminum Traxxas 4-Tec 2.0 Rear Hub Carriers (Black) (2) These optional Hot Racing Aluminum Rear Hub Carriers are a great upgrade for the Traxxas 4-Tec 2.0. These hubs are CNC machined from 6061 aluminum alloy and are anodized black. Replaces the stock TRA8352 plastic hubs. Aluminum Carriers Stub Axle (rear hub carrier uprights) for the Traxxas 4-Tec 2.0. Features: CNC machined 6061-T6 aluminum construction Black anodizing for durability, corrosion resistance, and great looks Replaces the factory plastic components Secondarily-processed machined beveled edges for stand out looks Upgrades the factory plastic Traxxas rear hub carrier set (TRA8352) This product was added to our catalog on July 18, 2021
$29.99
Hot Racing HRASXMX39X06, Hot Racing Steel Stub Axle w/Alum 24mm Wheel Hexes (4) - ONLY FOR Traxxas X-Maxx 6s
HRASXMX39X06, Hot Racing Steel Stub Axle w/Alum 24mm Wheel Hexes (4) Steel Stub Axle w/ 24mm Wheels, Hex, for Traxxas X-Maxx 6s Hot Racing's steel stub axles with aluminum 24mm wheel hexes for the Traxxas X-Maxx 6S. This set is an upgrade hop-up to the factory aluminum stub axle and plastic wheel hex. Comments: Replaces stock Traxxas 7753G and 7753R aluminum stub axle and 7756 wheel hex hub NOT compatible with the Traxxas X-Maxx 8S Includes: Four (4) steel stub axles Four (4) threaded 24mm wheel hexes Four (4) 4x21mm drive pins Four (4) M5x5mm setscrews (lock the drive pin in place) Features: CNC machined ANSI equivalent 1045 hardened steel stub axle with black oxide corrosion protection finish CNC machined 6061 aluminum hex with blue anodized finish Maintains stock 24mm hex Replaces the stock aluminum stub axle and plastic hex hubs Specifications: Hex width: 24mm Thread: M12 Total height: 46mm This product was added to our catalog on December 16, 2021
$139.99
Hot Racing HRATE117FL, Hot Racing Traxxas Slash 17mm Aluminum Hubs (F+3mm)
HRATE117FL, Hot Racing Traxxas Slash 17mm Aluminum Hubs (F+3mm) Hot Racing Traxxas Slash 17mm Aluminum Hub adapters for the Traxxas Electric Rustler, Slash, and Stampede 2WD vehicles are a great upgrade that will add approximately 4mm of width to the track width, helping to improve performance. Features: CNC machined 6061-T6 aluminum construction 17mm wheel nuts with o-ring grip Adapters are anodized black in color, wheel nuts are anodized vibrant blue Wheel mounting surface is approximately 4mm wider per side when compared to using the stock Traxxas TRA3654 hex hubs Includes: (2) Rear wheel adapters (2) Front +3mm Wheel Adapters (4) wheel nuts (4) axle hub barrel nuts (4) axle pins (1) hex wrench This product was added to our catalog on December 16, 2021
$32.99
Hot Racing HRATUDR311F, Hot Racing Traxxas Unlimited Desert Front HD Torsional Sway Bar Set (Red)
HRATUDR311F, Hot Racing Traxxas Unlimited Desert Front HD Torsional Sway Bar Set (Red) This product was added to our catalog on December 16, 2021
$34.99
You have seen 48 out of 92 products