DarwinFPV 3-4S 30A ESC is currently the cheapest in the FPV world and a direct replacement for the Cineape, designed to reduce the budget of entry-level FPV pilots as much as possible. At the same time, we have also filled the ESC with glue, which greatly reduces the risk of damage to components caused by frequent crashes by novices. Check out our other 20x20 ESCs and our Darwin FPV products! Specifications Input Voltage: 3-4S MCU: EFM8BB21 Max Continuous Current: 30A Max Burst Current: 35A Firmware: Bluejay G_H_30 Mounting Pattern: 20x20mm Weight: 4.9g Includes 1x DarwinFPV Bluejay 30A 8Bit 3-4S 20x20 4in1 ESC

Read more less

Pre-Orders shipping ASAP! For those just starting out with FPV drones and on a budget, BabyApe Ⅱ is a great choice. It builds on the design of the first generation of BabyApe, but with a higher spec and only a small price increase, making it the perfect starter drone for the cost-conscious flyer. DarwinFPV has always been committed to designing cost-effective FPV drone. They have accepted feedback from pilots, solved the problems that pilots are most concerned about, and brought better products to everyone who uses them. Adhering to these beliefs, DarwinFPV brings BabyApe Ⅱ. BabyApe Ⅱ is a 3.5-inch small freestyle FPV drone with a take-off weight of less than 250g that fulfills most countries' regulations. The BabyApe Ⅱ has a more powerful configuration, adopts a more reliable manufacturing process and a new power system, and has a higher level of performance, durability, and power. The flight time can reach 13 minutes, the flight distance is 1.5 kilometers, and the maximum speed is up to 92km/h.  The 4S version comes with powerful 1504-3600Kv motors, and choose between PNP (No RX)  or ELRS 2.4GHz for your receiver! Check out our other pre-built quads, as well as the rest of our DarwinFPV selection!  Features Compared with similar products of other brands, BabyApe Ⅱ only sells for $139.99, which once again perfectly reflects the super high-cost performance； It comes with 1504 motors and 3.5-inch propellers, the power is stronger and the response speed is faster; The camera and stack are protected by glue potting, which effectively prevents the risk of damage due to contact with metal particles, fine sand, gravel, weeds or dew, and the entire electronic system is more reliable and durable; The addition of a buzzer and extra LED lights is extremely beneficial for beginners, who frequently confront circumstances such as over-discharge the battery and locating drones due to mistakes that lead the drone to crash; The independent action camera base can be used with naked GoPro, thumb camera, etc. to record amazing images during flight at 4K/60 frames.   Specifications Brand: DarwinFPV Model: BabyApe Ⅱ 4S Frame: Wide X Wheelbase: 156mm Size: 126mmx150mmx50mm Flight Control: F411 MPU6500 AT7456E Firmware：DARWINF411 Firmware: BETAFPV_Nano_2400_RX The receiver's factory firmware is ELRS_V3.2.0 Reserved port: 1x SBUS(RX1 reverse)、2x Uarts(1,2)、2x Softserial, 1x I2C、1x RGB、1x Buzzer、1x USER(A15)、1x USB ESC: Bluejay 48KHz 3-6S 30A Motor:  4S version：1504-3600KV Propeller: HQProp T3.5x2x3GR-PC Weight: 135.4 g (analog version) Receiver: ELRS 2.4GHz Darwin FPV "Cement" Ultra Durable FPV Drone Camera Sensor type：1/3" CMOS Sensor Image：16:9 TV System: NTSC Horizontal Resolution：1200TVL Lens：2.1mm 160° Electronic Shutter: 1/50~1/100000 sec Video Output: CVBS Min. Illumination：0.001Lux wb: automatic DNR: 3D DNR WDR: 100db Input voltage: DC 3.7-24V Working current：80mA@DC12V/170mA@DC5V IP: IP67 Size：19x19mm Weight：7.9g DarwinFPV 25/200/400/600mW VTX Output Power: 25/200/400/600mW(adjustable) Frequency: 5.8Hz 40port Power Supply Voltage Range: 5V Weight: 3.5g Pitch: 28x15mm(length x width) Protocol: SmartAudio Indicator Light Description: Includes 1x DarwinFPV BNF Baby Ape V2 3.5" Analog Micro Quad - 4S - Choose Your Receiver 4x HQProp T3.5x2x3GR-PC 2x Battery cable strip ( 10x170mm) 2x EVA shock pad（thickness：10㎜） 1x Spare screws bag 1x Sticker 1x Manual

Read more less

Pre-Orders shipping ASAP! For those just starting out with FPV drones and on a budget, BabyApe Ⅱ is a great choice. It builds on the design of the first generation of BabyApe, but with a higher spec and only a small price increase, making it the perfect starter drone for the cost-conscious flyer. DarwinFPV has always been committed to designing cost-effective FPV drone. They have accepted feedback from pilots, solved the problems that pilots are most concerned about, and brought better products to everyone who uses them. Adhering to these beliefs, DarwinFPV brings BabyApe Ⅱ. BabyApe Ⅱ is a 3.5-inch small freestyle FPV drone with a take-off weight of less than 250g that fulfills most countries' regulations. The BabyApe Ⅱ has a more powerful configuration, adopts a more reliable manufacturing process and a new power system, and has a higher level of performance, durability, and power. The flight time can reach 13 minutes, the flight distance is 1.5 kilometers, and the maximum speed is up to 92km/h.  The 6S version comes with powerful 1504-2300Kv motors, and choose between PNP (No RX)  or ELRS 2.4GHz for your receiver! Check out our other pre-built quads, as well as the rest of our DarwinFPV selection!  Features Compared with similar products of other brands, BabyApe Ⅱ only sells for $139.99, which once again perfectly reflects the super high cost performance； It comes with 1504 motors and 3.5-inch propellers, the power is stronger and the response speed is faster; The camera and stack are protected by glue potting, which effectively prevents the risk of damage due to contact with metal particles, fine sand, gravel, weeds or dew, and the entire electronic system is more reliable and durable; The addition of a buzzer and extra LED lights is extremely beneficial for beginners, who frequently confront circumstances such as over-discharge the battery and locating drones due to mistakes that lead the drone to crash; The independent action camera base can be used with naked gopro, thumb camera, etc. to record amazing images during flight at 4K/60 frames.   Specifications Brand: DarwinFPV Model: BabyApe Ⅱ 6S Frame: Wide X Wheelbase: 156mm Size: 126mmx150mmx50mm Flight Control: F411 MPU6500 AT7456E Firmware： DARWINF411 Firmware: BETAFPV_Nano_2400_RX The receiver's factory firmware is ELRS_V3.2.0 Reserved port: 1x SBUS(RX1 reverse)、2x Uarts(1,2)、2x Softserial, 1x I2C、1x RGB、1x Buzzer、1x USER(A15)、1x USB ESC: Bluejay 48KHz 3-6S 30A Motor： 6S version：1504-2300KV Propeller: HQProp T3.5x2x3GR-PC Weight: 135.4 g(analog version) Receiver: ELRS 2.4GHz Darwin FPV "Cement" Ultra Durable FPV Drone Camera Sensor type：1/3" CMOS Sensor Image：16:9 TV System: NTSC Horizontal Resolution：1200TVL Lens：2.1mm 160° Electronic Shutter: 1/50~1/100000 sec Video Output: CVBS Min. Illumination：0.001Lux wb: automatic DNR: 3D DNR WDR: 100db Input voltage: DC 3.7-24V Working current：80mA@DC12V/170mA@DC5V IP: IP67 Size：19x19mm Weight：7.9g DarwinFPV 25/200/400/600mW VTX Output Power: 25/200/400/600mW(adjustable) Frequency: 5.8Hz 40port Power Supply Voltage Range: 5V Weight: 3.5g Pitch: 28x15mm(length x width) Protocol: SmartAudio Indicator Light Description: Includes 1x DarwinFPV BNF Baby Ape V2 3.5" Analog Quad - 6S - Choose Your Receiver 4x HQProp T3.5x2x3GR-PC 2x Battery cable strip ( 10x170mm) 2x EVA shock pad（thickness：10㎜） 1x Spare screws bag 1x Sticker 1x Manual

Read more less

This is a unique stack for the demands of the industry today. It has a 25.5x25.5 M2 (Whoop) mount pattern because there are now many frames that are designed with that pattern. The problem is that high-powered AIO boards are way overpriced due to the forever chip shortage and still have a high failure rate. Much of the failures are associated with the cramped space constraints of the small board. We split the ESC and FC but called for the ESC to have a nearly empty top side and the FC to have nearly all its components on the bottom and sit inside the footprint of the ESC solder pads. ALL of the FC's solder pads are also on the TOP. When you assemble the stack inside your frame, you will be able to access and solder ALL pads on BOTH boards. Additionally, the FC has a black box chip which is rare on AIO boards. Check out our other AIO Flight Controllers and our Darwin FPV products! Specifications F722 MCU: STM32F722RET6(216MHz) Gyro: MPU6000 Barometer: BMP280(I2C) OSD Chip: Betaflight OSD AT7456E Blackbox: 16MB UARTS: 5 I2C: SDA / SLA pads LED: Yes Beeper: Yes Firmware Target: DARWINF722HD FC Mounting Pattern: 25.5x25.5mm Dimensions: 37x36x10.8mm 4in1 ESC Input Voltage: 3-6S Max. Continuous Current: 50A Max. Burst Current: 60A  MCU: EFM8BB21F16G BEC: 5V/2A and 10V/2A Current Sensor: Yes (Scale 125) Mounting Dimensions: 25.5x25.5mm(M2) Dimensions 37x36x10.8mm Includes 1x FPV Cycle Darwin FPV F722 25x25 Flight Controller 1x FPV Cycle Darwin FPV 45A 3-6S 25x25 4in1 ESC 1x XT60-7CM-14AWG Power cables 1x 25V 470uF capacitor 8 x M2*6.5mm Damping rings 4 x M2 nuts Wiring Diagram

Read more less