Products
E-flite EFLB1501S45, 150mAh 1S 3.7V 45C LiPo Battery: PH 1.5 (Ultra Micro)
EFLB1501S45, 150mAh 1S 3.7V 45C LiPo Battery: PH 1.5 (Ultra Micro)
$7.99
E-flite EFLB2001S45, E-flite 1S LiPo Battery 45C (3.7V/200mAh)
EFLB2001S45, E-flite 1S LiPo Battery 45C (3.7V/200mAh) A replacement 200mAh 45C 1s (3.7V) Li-Po Battery from E-Flite. Suited for use with the Inductrix FPV, and many other applications that commonly accept a 150-210mAh sized battery. This product was added to our catalog on October 14, 2021
$8.99
E-flite EFLB5001S25, E-flite 1S 25C LiPo Battery Pack (3.7V/500mAh) w/JST Connector
EFLB5001S25, E-flite 1S 25C LiPo Battery Pack (3.7V/500mAh) w/JST Connector This is a replacement E-flite 1S - 3.7V, 25C, 500mAh LiPo Battery Pack. Specifications: Type: LiPo Capacity: 500mAh Voltage: 3.7V Weight: 0.51 oz (14.5 g) Configuration: 1S Length: 2.35 in (59.5mm) Width: 0.75 in (19.0mm) Height: 0.30 in (7.5mm) Maximum Continuous Discharge: 25C Maximum Continuous Current: 12.5A This product was added to our catalog on December 20, 2021
$11.99
RaceDayQuads EMAX BNF Tinyhawk II Freestyle Analog Toothpick Quad - FRSKY
All product containing lithium batteries must be shipped by a ground shipping method.Following the groundbreaking performance of the predecessor, comes the newly re-invented Tinyhawk II Freestyle, the perfect beginner outdoor FPV quad! Check out all our pre-built quads, and our selection of EMAX gear! Features Durable aerospace grade 3k woven carbon fiber BlHeli_S ESC F4 (MATEKF411RX Firmware) Flight Controller RunCam Nano 2 FPV camera More powerful VTX with 25/100/200mw power levels Smart Audio connected FRSKY D8 compatible Efficient Emax 1103 7000Kv brushless motors Avan Rush 2.5" props Specifications Frame Wheelbase: 115mm Dry Weight: 49g All Up Weight: 79g with 2x 450mAh 1S battery Frame Material: Carbon Fiber Motors Stator Size: 1103 Kv: 7000kv Propeller Mount: T-mount, 1.5mm shaft Propeller: Avan Rush 2.5" All-In-One (AIO) Flight Controller Flight Controller: F4 (MATEKF411RX Firmware) ESC: 4-in-1 5A BlHeli_S Receiver: EMAX SPI Receiver (Compatible with FrSky D8 mode) Battery Connector: JST-PH2.0 Duo FPV System Ham radio license required for use in North America. VTX Power: 25/100/200mw Switchable (set to stay at 25mW until armed)* Channels: 37CH incl. Raceband Camera: RunCam Nano 2 1/3" 700TVL CMOS Smart Audio Connected Includes 1x Tinyhawk II Freestyle BNF 2x EMAX 450mAh 1S HV Battery 1x 1S USB LiPo Charger 1x Hardware Kit
$139.99
RaceDayQuads EMAX RTF Tinyhawk II Freestyle Ready To Fly Analog Kit w/ Goggles, Radio Transmitter, Case & Drone
All products containing lithium batteries must be shipped by a ground shipping method. The TinyHawk II Freestyle RTF kit has literally everything you need to get started in the world of freestyle FPV! Quad, Goggles, Transmitter, Batteries, Charger and an awesome case to carry all of it. This kit is the best way to start from nothing and work your way up to learning more advanced freestyle tricks. It's also a great option if you're looking for a compact setup you can keep with you to rip a few quick packs wherever and whenever! Check out our other RTF combos, all our pre-built quads, all things Tinyhawk, and our EMAX selection! Specifications Frame Wheelbase: 115mm Dry Weight: 49g All Up Weight: 79g with 2x 450mAh 1S battery Frame Material: Carbon Fiber Motors Stator Size: 1103 Kv: 7000kv Propeller Mount: T-mount, 1.5mm shaft Propeller: Avan Rush 2.5" All-In-One (AIO) Flight Controller Flight Controller: F4 (MATEKF411RX Firmware) ESC: 4-in-1 5A BlHeli_S Receiver: EMAX SPI Receiver Battery Connector: JST-PH2.0 Duo FPV System VTX Power: 25/100/200mw Switchable (set to stay at 25mW until armed)* Channels: 37CH incl. Raceband Camera: RunCam Nano 2 1/3" 700TVL CMOS Smart Audio Connected Includes 1x Tinyhawk 2 Freestyle Drone 1x E6 Transmitter 1x Transporter Goggles w/ Battery + Antennas 2x EMAX 450mAh 1S HV Battery 1x 1S USB LiPo Charger 1x Screwdriver + Hardware Kit 1x Carbon Fiber Carrying Case *Please note that even if you unlocked the video transmitter (VTX) per the manual and are changing power levels via the OSD/Smart Audio (VTX SA), the Tinyhawk II Freestyle is set to stay at 25mW until you arm the mot
$229.99
EMAX EMAX RTF Tinyhawk II Ready to Fly Analog Kit w/ Goggles, Radio Transmitter, Case and 75mm Indoor Racing Whoop Drone
All items with batteries must be shipped by a ground shipping method. The TinyHawk 2 RTF kit has everything you need to enjoy micro flight, all packed into a handy carrying case! This is truly the ideal way to try out FPV! 2 batteries are included (a 1S and a 2S), but if you want to maximize your air time, we recommend picking up a few of the following RDQ Series LiPos: 1S 450mAh - PH2.0 2S 300mAh - PH2.0 Check out our other RTF combos, all our pre-built quads, all things Tinyhawk, and our EMAX selection! Specifications Frame Wheelbase: 75mm Dry Weight: 31.2g All Up Weight: 43.5g with 1x 450mAh 1S battery Frame Material: Polypropylene Motors Stator Size: 0802 Kv: 16000kv Propeller Mount: Push-On Avan TH-style Propeller: Avan Turtlemode 4-Blade All-In-One (AIO) Flight Controller Flight Controller: F4 (MATEKF411RX Firmware) ESC: 4-in-1 5A BlHeli_S Receiver: EMAX SPI Receiver (Compatible with FrSky D8 mode) Battery Connector: JST-PH2.0 FPV System VTX Power: 25/100/200mw Switchable Channels: 37CH incl. Raceband Camera: RunCam Nano 2 1/3" 700TVL CMOS Smart Audio Connected Includes 1x Tinyhawk II FPV Racing Drone 1x EMAX Transporter 5.8G FPV Goggles 1x EMAX Transporter 18650 Goggle Battery Pack w/ USB Charging 1x EMAX E6 Transmitter 1x EMAX 450mAh 1S HV Battery 1x EMAX 300mAh 2S HV Battery 2x CCW + 2x CW Spare Props 1x 1S-2S USB LiPo Charger 1x Screwdriver + Hardware Kit 1x Micro USB Charging Cable 1x Faux Carbon Fiber Carrying Case
$208.99
RaceDayQuads EMAX TH1202.5 11,000Kv Motor
This is a replacement motor for the Emax Nanohawk X. This motor also be used on 2-3" builds! Check out our other Nanohawk X accessories, and all our EMAX selection! Specifications Kv: 11000Kv Input Voltage: 1S LiPo Motor Dimensions: Φ15mm x 16mm Stator Dimensions: Φ12mm x 025mm Shaft Diameter: 1.5mm Mounting Pattern: Φ9mm Weight (w/ wires): 4.5g Includes 1x EMAX TH 1202.5 11000Kv Motor
$11.99
RaceDayQuads EMAX Tinyhawk 3.8V 1S 450mAh LiHV Whoop/Micro Battery - PH2.0
All batteries must be shipped by a ground shipping method. The Tinyhawk 1s lipo battery is a big part of the whole design around the great flight performance of the Tiny Hawk. The weight, the size, and the power from the High Voltage 450mah capacity cell were all considered during the design process. Engineers tested countless hours of flight and performance to achieve the best Lipo battery for you to enjoy up to 4 minutes of flying time! Our pilots agree that at least 4-6 batteries will be required to have the best flying experience for an all day fun fly! Required charger type: Any charger that has 4.35 High Voltage capabilities. This will keep you flying for up to 4 minutes per charge. Be sure to check out our all micro packs, and all our EMAX gear! Specifications Voltage: 1S 4.35V HV Capacity: 450 mAh Discharge rating: 80c/160c Connector: PH2.0 Includes 1x EMAX TinyHawk 3.8V 1S 450mAh LiHV Whoop/Micro Battery - PH2.0
$7.99
RaceDayQuads Flywoo BNF Firefly 2S Nano Baby 20 2" Analog Quad - ELRS 2.4GHz
The Flywoo Firefly Nano Baby 20 2S Micro Quadcopter BNF Analog comes with Flywoo's Nano Camera V2 and is equipped with the most efficient micromotor and the top AIO flight controller on the market! This micro quadcopter will bring you an unprecedented flying experience; the Firefly Nano Baby 20 can do crazy acro and keep up with all the tricks up your sleeve. Check out the rest of our pre-built quads, as well as the rest of our Flywoo selection! Features Comes with 1002 15500KV motors and Gemfan 2015 - 2 blade propellers, which provide the best balance of performance and flight time. Versatile and highly integrated circuit board - GOKU Versatile F405 2S 12A AIO. Built-in ELRS 2.4g RX. Have multiple sets of serial external devices. Easy switch battery mount design. Explorer 2S 420mAh for Racing, Explorer 2S 750mAh for long flight time. Great mount compatibility for cameras like the Thumb Pro, Peanut, GO2, Thumb, and related Specifications Weight: 33.8g (without battery) FC & ESC: GOKU Versatile F405 2S 12A AIO Frame: Firefly 2S Nano Baby 20 Analog Frame kit Motors: Flywoo ROBO 1002 15500KV Props: Gemfan 2015-2 blade VTX: GOKU VTX625 V2 450mW Nano VTX Camera: Flywoo 1.2g 1S Nano camera V2 GOKU Versatile F4 5-IN-1 1S AIO FC Size: 30x30mm Weight: 4.1g Hole: 25.5x25.5-3mm MCU: STM32F405 UARTS: 1,2,3,4,5,6 MOTOR: M1-M4 OUTPUT I2C: SCL/SDA GYRO: ICM42688 Barometer: BMP280 LED: 2x WS2812 Flash: 8M BEC: 5V 2A Firmware: FLYWOOF405S_AIO Onboard 4in1 ESC Built-in 1S/2S 12A BL_S 4in1 ESC Support Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600 Input Voltage: 1-2S Lipo Firmware: BLHELI_S Firmware: Z_H_30_REV16.7 Flywoo ROBO 1002 15500Kv Motor Kv: 15500Kv Input Voltage: 2S LiPo Stator Dimensions: Φ10mmx2mm Shaft Diameter: Φ 1.5mm Wire Dimensions: 30AWGx40mm Weight (w/ wires): 2.4g Flywoo 1S Nano Camera V2 Image Sensor: 1/3" CMOS Sensor Horizontal Resolution: 1200 TVL TV System: NTSC and PAL(switchable) MENU: Support IMAGE: 4:3 Synchronization: Internal Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000 S/N Ratio: >52dB (AGC OFF) Video Output: CVBS Lens: 1.8mm/F2.5 Min. illumination: 0.001Lux Auto Gain Control: YES BLC: YES WDR: Global WDR DNR: 3D DNR Dimensions: 14x14mm Wide Power Input: DC 5-25V Work Temperature: -20°C~+60C Work Humidity: 20%~80% Weight: 1.2g (N.W.) Includes 1 x Flywoo BNF Firefly 2S Nano Baby 20 2" Quad Analog w/ GOKU VTX625 V2 & Nano Camera V2 - ELRS 2.4GHz 2 x Sets of 2015-2 props 1 x Screw spare packs 2 x Battery holder 4 x Prop guards
$179.99
RaceDayQuads Flywoo BNF Firefly DC16 Nano Baby HD V2.0 1S 1.6" Deadcat Micro Quad w/ HDZero Whoop Lite & Nano Lite Cam - ELRS 2.4 GHz
Experience superior performance with the Flywoo BNF Firefly DC16 Nano Baby V2.0 1S Deadcat Analog Micro Quad. Boasting a 30% power increase compared to its predecessor, it offers extended flight time while providing an incredibly stable flight experience. It comes with a new and improved canopy design for increased camera protection and a crash-resistant bottom plate for added durability. Enjoy the unmatched experience of this incredibly crafted drone from Flywoo. Experience the great capabilities of HDzero System. Check out our other pre-built quads, as well as other great products from Flywoo! Features Redesigned canopy with enhanced aesthetics and reinforced camera protection. The bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter. Equipped with ROBO 1002 19800KV motor and 1608 3-bladed 40mm propellers, delivering a 30% increase in power, reduced noise, and enhanced flight stability. The GOKU Versatile F411 ELRS 1S AIO V2 boasts an ELRS 2.4G receiver, expertly connected via UART 2 instead of SPI for superior performance. A30 plug supports a continuous current of 15A, providing greater power and longer flight times compared to the PH2.0 connector. New battery compartment design allows for easy replacement of batteries of different models. Dead Cat Style The drone boasts a dead cat design that enhances stability, extends battery life and provides an unobstructed flying experience with hidden propellers. New Design Redesigned canopy with enhanced aesthetics and reinforced camera protection.Bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter. Efficient Power Combo Equipped with ROBO 1002 19800KV motor and 1608 3-bladed 40mm propellers, delivering a 30% increase in power, reduced noise, and enhanced flight stability. Ultra-light AIO with ELRS 2.4G RXThe drone's GOKU Versatile F411 VTX 1S AIO V2 includes a built-in 250mW video transmitter, enabling an extended flight range and ultimate lightweight design without sacrificing performance, with improved circuit board stability. HD Digital VTX System The HDZero Nano Lite Camera is a revolutionary product designed for lightweight drones, weighing only 1.5g and combined with the new Whoop Lite VTX at 4.5g. Supporting 1-3S power input, it can record in 720P/60FPS with ultra-low latency of less than 19ms and features OSD function configuration through Betaflight Configurator. More Power, More Flight Time The A30 plug can sustain a continuous current of 15A, whereas the PH2.0 connector can only support 4.5A. Given the same capacity, the A30 plug can release more current, providing greater power and, as a result, longer flight times even when flying at full speed. Specifications Frame Kit: Firefly 1S DC16 Nano baby quad Frame kit Motor: ROBO 1002 19800KV Electronic: GOKU Versatile F411 ELRS 1S 5A AIO V2.0 Propeller: 1608-3 Blade 40mm 1.5mm Shaft Camera: Nano Lite Cam Weight: 31g GOKU Versatile F411 ELRS 1S 5A AIO V2.0Flight Controller MCU: STM32F411CEU6 GYRO: ICM42688 UARTS: 1/2 Soft serial port: 1 I2C: SCL/SDA BEC: 5V Input Voltage: 1S (<4.35v) Firmware: FLYWOOF411_5IN1_AIO Mounting: 25x25mm, M2 Onboard 4in1 ESC MCU: EFM8BB21 Power supply: 1S LiPo/LiPo HVCurrent: 5A Firmware: BLHeli_S Factory firmware: O_H_5_REV16_8.HEX Default protocol: DSHOT 150/300/600 ELRS 2.4G RX (UART2) ROBO 1002 19800KV Configuration: 9N12P Stator Diamter: 10mm Stator Length: 2mm Shaft Diameter: 1.5mm Motor Dimension(Dia.xLen): Φ13.5x7.75mm Weight(g): 2.5(5cm wire) Idle current(5)@5V(A): 1.3 No.of Cells(Lipo): 1S Max Continuous Power(W)3S: 44 Internal Resistance: 89mΩ Max Current(3S): 11.8A Max Efficiency Current: (2-4A)>84% HDZERO WHOOP LITE VTX Input Voltage: 1S-3S Output Power: 23mW, 200mW Operating Frequency: 5.727-5.850GHz Resolution: 1280x720@60fps Power Consumption: 5W @ 25mW, 5.8W @ 200mW MSP Canvas Mode: Yes Antenna Interface: U.FL (IPEX 1) Operating Temperature: 32-104°F Mounting Pattern: 25x25mm, M2 Weight: 7g total package HDZERO NANO LITE CAMERA Size: 14x16x11mm Weight: 1.5gram Sensor: 0.5 inch, up to 10650 mV/Lux-secUltra-high sensitive CMOS sensor FOV:- 4:3 D:130° H:108° V:84°- 16:9 D:122° H:108° V:65° Includes 1x Flywoo BNF Firefly DC16 Nano Baby V2.0 HD 1S 1.6" Deadcat Micro Quad w/ HDZero Whoop Lite & Nano Lite Cam - ELRS 2.4 GHz 4x 1608 -3 40mm 1.5mm shaft 2x TPU battery mount 1x hardware screws set 4x Prop guards
$239.99
RaceDayQuads Flywoo BNF Firefly DC16 Nano Baby HD V2.0 1S 1.6" Deadcat Micro Quad w/ Walksnail Avatar Mini 1S Lite & Avatar Lite Cam - ELRS 2.4 GHz
Experience superior performance with the Flywoo BNF Firefly DC16 Nano Baby V2.0 1S Deadcat Analog Micro Quad. Boasting a 30% power increase compared to its predecessor, it offers extended flight time while providing an incredibly stable flight experience. It comes with a new and improved canopy design for increased camera protection and a crash-resistant bottom plate for added durability. Enjoy the unmatched experience of this incredibly crafted drone from Flywoo. Experience the elite capabilities of HD Walksnail System. Check out our other pre-built quads, as well as other great products from Flywoo! Features Redesigned canopy with enhanced aesthetics and reinforced camera protection. The bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter. Equipped with ROBO 1002 19800KV motor and 1608 3-bladed 40mm propellers, delivering a 30% increase in power, reduced noise, and enhanced flight stability. The GOKU Versatile F411 ELRS 1S AIO V2 boasts an ELRS 2.4G receiver, expertly connected via UART 2 instead of SPI for superior performance. A30 plug supports a continuous current of 15A, providing greater power and longer flight times compared to the PH2.0 connector. New battery compartment design allows for easy replacement of batteries of different models. Dead Cat Style The drone boasts a dead cat design that enhances stability, extends battery life and provides an unobstructed flying experience with hidden propellers. New Design Redesigned canopy with enhanced aesthetics and reinforced camera protection.Bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter. Efficient Power Combo Equipped with ROBO 1002 19800KV motor and 1608 3-bladed 40mm propellers, delivering a 30% increase in power, reduced noise, and enhanced flight stability. Ultra-light AIO with ELRS 2.4G RX The drone's GOKU Versatile F411 ELRS 1S AIO V2 boasts an ELRS 2.4G receiver, expertly connected via UART 2 instead of SPI for superior performance. This allows for the ultimate lightweight design without sacrificing functionality. HD Digital VTX System The Walksnail Avatar HD Mini 1S Lite is a lightweight VTX designed for 1S whoop drones, featuring H.265 high-efficiency video coding technology, 1080P/60FPS image recording with 22ms ultra-low latency, and built-in 8 GB storage for interference-free HD video recording and USB exporting. More Power, More Flight Time The A30 plug can sustain a continuous current of 15A, whereas the PH2.0 connector can only support 4.5A. Given the same capacity, the A30 plug can release more current, providing greater power and, as a result, longer flight times even when flying at full speed. Specifications Frame Kit: Firefly 1S DC16 Nano baby quad Frame kit Motor: ROBO 1002 19800KV Electronic: GOKU Versatile F411 ELRS 1S 5A AIO V2.0 Propeller: 1608-3 Blade 40mm 1.5mm Shaft Camera: Avatar Lite Cam Weight: 33g GOKU Versatile F411 ELRS 1S 5A AIO V2.0Flight Controller MCU: STM32F411CEU6 GYRO: ICM42688 UARTS: 1/2 Soft serial port: 1 I2C: SCL/SDA BEC: 5V Input Voltage: 1S (<4.35v) Firmware: FLYWOOF411_5IN1_AIO Mounting: 25x25mm, M2 Onboard 4in1 ESC MCU: EFM8BB21 Power supply: 1S LiPo/LiPo HVCurrent: 5A Firmware: BLHeli_S Factory firmware: O_H_5_REV16_8.HEX Default protocol: DSHOT 150/300/600 ELRS 2.4G RX (UART2) ROBO 1002 19800KV Configuration: 9N12P Stator Diamter: 10mm Stator Length: 2mm Shaft Diameter: 1.5mm Motor Dimension(Dia.xLen): Φ13.5x7.75mm Weight(g): 2.5(5cm wire) Idle current(5)@5V(A): 1.3 No.of Cells(Lipo): 1S Max Continuous Power(W)3S: 44 Internal Resistance: 89mΩ Max Current(3S): 11.8A Max Efficiency Current: (2-4A)>84% Walksnail Avatar HD Mini 1S Lite Model: Avatar mini 1s module Communication Frequency: 5.725-5.850GHz Transmitter Power (EIRP): FCC:<25.5dBm;CE:<14dBm;SRRC:<20dBm; MIC:<25dBm I/O Interface: JST1.0x6(Power in)JST1.0x4(USB) Mounting Holes: 25.5x25.5mm Dimensions: 30x30x6.5mm Storage: 8G Recording: 1080p/720p Weight: 5.1g Operating Temperature: -20-40℃ Channels: 8 Wide Power Input: 3.1V-5V Supported FC System: Betaflight OSD: Canvas mode Bitrate: 25mbps, 50mbps Latency Average delay: 22ms Antenna: IPEX Avatar lite camera Model: Avatar lite camera Image Sensor: 1/2.7”1nch Resolution: 1080P/60fps,720P/120fps,720P/60fps Ratio: 16/9 4/3 Lens:2.1mm FOV:170° Aperture:F2.0 Shutter Rolling: Rolling shutter Min.Illumination: 0.001Lux Weight: 1.8g Dimensions: 14x14x16mm Includes 1x Flywoo BNF Firefly DC16 Nano Baby V2.0 HD 1S 1.6" Deadcat Micro Quad w/ Walksnail Avatar Mini 1S Lite & Avatar Lite Cam - ELRS 2.4 GHz 4x 1608 -3 40mm 1.5mm shaft 2x TPU battery mount 1x hardware screws set 4x Prop guards
$239.99
RaceDayQuads Flywoo BNF Firefly FR16 Nano Baby Analog V2.0 1.6" 1S Micro Quad - ELRS 2.4 GHz
The FR16 Nano Baby V2 is a meticulously crafted microdrone with improved appearance, flight time, and power compared to its predecessor. Power has increased by 30%, with flexible flight, exceptional maneuverability, and higher speeds. A new canopy reinforces camera protection, while a new bottom plate adds sturdiness and crash resistance. The drone is equipped with a special gold-purple edition ROBO 1002 23,500KV motor and GOKU Versatile F411 VTX 1S AIO V2 with 250mW video transmitter. The Flywoo 1S Nano camera V3 delivers clearer and better image quality on this quad. Check out our other pre-built quads, as well as other great products from Flywoo! Features Redesigned canopy with enhanced aesthetics and reinforced camera protection. The bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter. Equipped with ROBO 1002 23,500KV motor and 1609 4-bladed 40mm propellers, delivering a 30% increase in power, reduced noise, and enhanced flight stability. Ultra-light GOKU Versatile F411 1S VTX AIO V2 with upgraded circuit board stability and a 250mw video transmitter, enabling an extended flight range. A30 plug supports a continuous current of 15A, providing greater power and longer flight times compared to the PH2.0 connector. Upgraded Flywoo 1S Nano camera V3 delivers clearer and better image quality. New battery compartment design allows for easy replacement of batteries of different models. Specification Motor: ROBO 1002 23500KV Electronics: GOKU Versatile F411 VTX 1S 5A AIO V2.0 w/250mW VTX Props: 1609 - 4 blade 40mm 1.5mm Shaft Camera: Flywoo 1S Nano Camera V3 Receiver: ExpressLRS 2.4GHz Weight: 26g Flight Time: Explorer 1S 450mAh HV V2: 4m - Explorer 1s 750mAh HV V2: 6m (approximate) Speed: 80km/h (approximate) GOKU Versatile F411 VTX 1S 5A AIO V2.0 w/ 250mw VTX Flight Controller MCU: STM32F411CEU6 GYRO: ICM42688 UARTS: 1/2 Soft serial port：1 I2C: SCL/SDA BEC: 5V Input Voltage: 1S (<4.35v) Firmware: FLYWOOF411_5IN1_AIO Mounting: 25x25mm, M2 Onboard 4in1 ESC MCU: EFM8BB21 Power supply: 1S LiPo/LiPo HV Current: 5A Firmware: BLHeli_S Factory firmware: O_H_5_REV16_8.HEX Default protocol: DSHOT 150/300/600 Onboard 5.8g VTX Output power: 25mw~250mw switchable Frequency: 40CH Frequency: 5.8GHz 5 bands 40 channels(include Race band) IRC ready Flywoo ROBO 1002 23500KV Fpv Motor: Configuration: 9N12P Stator Diameter: 10mm Stator Length: 2mm Shaft Diameter: 1.5mm Motor Dimension(Dia.xLen): Φ13.5x7.75mm Weight(g): 2.5(5cm wire) Idle current(5)@5V(A): 1.5 No.of Cells(Lipo): 1S Max Continuous Power(W)3S: 52 Internal Resistance: 75mΩ Max Current(3S): 14A Max Efficiency Current: (2-4A)>84% Flywoo 1S Nano Camera V3 Model: Flywoo 1S Nano Camera V3 Image Sensor: 1/3" CMOS Sensor Horizontal Resolution: 1200 TVL TV System: NTSC and PAL(switchable) MENU: Support IMAGE: 4:3 Synchronization: Internal Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000 S/N Ratio: >52dB (AGC OFF) Video Output: CVBS Lens: 1.8mm/F2.5 Min. illumination: 0.001Lux Auto Gain Control: YES BLC: YES WDR: Global WDR DNR: 3D DNR Dimensions: 14x14mm Wide Power Input: DC 3.7-18V Work Temperature: -20°C~+60C Work Humidity: 20%~80% Weight: 2.1g Includes 1x Flywoo BNF Firefly FR16 Nano Baby Analog V2.0 1.6" 1S Micro Quad - ELRS 2.4 GHz 4x 1609 - 4 40mm 1.5mm shaft 2x TPU Battery Mount 1x Hardware Screw Set 4x Prop guards
$174.99
RaceDayQuads Flywoo BNF Firefly FR16 Nano Baby HD V2.0 1S 1.6" Micro Quad w/ HDZero Whoop Lite & Nano Lite Cam - ELRS 2.4 GHz
The Firefly 1S Nano Baby V2 is a micro-drone with improved flight time, power and design compared to its predecessor. Power has increased by 30%, with flexible flight, exceptional maneuverability, and higher speeds. A new canopy for camera protection and a bottom plate for sturdiness are integrated. Additionally, this model includes the GOKU F411 ELRS 1S AIO V2 with ELRS 2.4G receiver (UART 2) for a lightweight design with optimal performance. This version utilizes the elite capabilities of the HDZero HD digital VTX system. The HDZero Nano Lite Camera is a revolutionary product designed for lightweight drones, weighing only 1.5g and combined with the new Whoop Lite VTX at 4.5g. Supporting 1-3S power input, it can record in 720P/60FPS with ultra-low latency of less than 19ms and features OSD function configuration through Betaflight Configurator. Check out our other pre-built quads, as well as other great products from Flywoo! Features: Redesigned canopy with enhanced aesthetics and reinforced camera protection. The bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter. Equipped with ROBO 1002 23,500KV motor and 1609 4-bladed 40mm propellers, delivers a 30% increase in power, flexible flight, and impressive speeds - perfect for racing competitions. The GOKU Versatile F411 ELRS 1S AIO V2 boasts an ELRS 2.4G receiver, expertly connected via UART 2 instead of SPI for superior performance. A30 plug supports a continuous current of 15A, providing greater power and longer flight times compared to the PH2.0 connector. New battery compartment design allows for easy replacement of batteries of different models. Specifications Motor: ROBO 1002 23,500KV Electronic: GOKU Versatile F411 ELRS 1S 5A AIO V2.0 Props: 1609 - 4 blade 40mm 1.5mm Shaft HD Digital VTX System: HDZero Whoop Lite Bundle Receiver: ExpressLRS 2.4GHz Weight: 31g Flight Time: Explorer 1S 450mAh HV V2: 4m - Explorer 1s 750mAh HV V2: 6m (approximate) Speed: 70km/h (approximate) GOKU Versatile F411 ELRS 1S 5A AIO V2.0Flight Controller MCU: STM32F411CEU6 GYRO: ICM42688 UARTS: 1/2 Soft serial port: 1 I2C: SCL/SDA BEC: 5V Input Voltage: 1S (<4.35v) Firmware: FLYWOOF411_5IN1_AIO Mounting: 25x25mm, M2 Onboard 4in1 ESC MCU: EFM8BB21 Power supply: 1S LiPo/LiPo HVCurrent: 5A Firmware: BLHeli_S Factory firmware: O_H_5_REV16_8.HEX Default protocol: DSHOT 150/300/600 ELRS 2.4G RX (UART2) Flywoo ROBO 1002 23500KV Fpv Motor: Configuration: 9N12P Stator Diameter: 10mm Stator Length: 2mm Shaft Diameter: 1.5mm Motor Dimension(Dia.xLen): Φ13.5x7.75mm Weight(g): 2.5(5cm wire) Idle current(5)@5V(A): 1.5 No.of Cells(Lipo): 1S Max Continuous Power(W)3S: 52 Internal Resistance: 75mΩ Max Current(3S): 14A Max Efficiency Current: (2-4A)>84% HDZero Whoop LITE VTX Input Voltage: 1S-3S Output Power: 23mW, 200mW Operating Frequency: 5.727-5.850GHz Resolution: 1280x720@60fps Power Consumption: 5W @ 25mW, 5.8W @ 200mW MSP Canvas Mode: Yes Antenna Interface: U.FL (IPEX 1) Operating Temperature: 32-104°F Mounting Pattern: 25x25mm, M2 Weight: 7g total package HDZero Nano LITE Camera Size: 14x16x11mm Weight: 1.5gram Sensor: 0.5 inch, up to 10650 mV/Lux-secUltra-high sensitive CMOS sensor FOV:- 4:3 D:130° H:108° V:84°- 16:9 D:122° H:108° V:65° Includes 1x Flywoo BNF Firefly FR16 Nano Baby HD V2.0 1S 1.6" Micro Quad w/ HDZero Whoop Lite & Nano Lite Cam - ELRS 2.4 GHz 4x 1609 - 4 40mm 1.5mm shaft 2x TPU Battery Mount 1x Hardware Screw Set 4x Prop guards
$239.99
RaceDayQuads Flywoo BNF Firefly FR16 Nano Baby HD V2.0 1S 1.6" Micro Quad w/ Walksnail Avatar Mini 1S Lite & Avatar Lite Cam - ELRS 2.4 GHz
The FR16 Nano Baby V2 is an advanced microdrone with improved flight time, power, and appearance over its predecessor. It's 30% more powerful despite being heavier, with flexible flight, great maneuverability, and higher speeds. A newly designed canopy and plate provide crash resistance, and it's equipped with a ROBO 1002 23500KV motor. Plus, the GOKU Versatile F411 ELRS 1S AIO V2 + ELRS 2.4G receiver ensures a lightweight, top-performing design. This version utilizes the elite capabilities of the Walksnail HD digital VTX system. The Walksnail Avatar HD Mini 1S Lite is a lightweight VTX designed for 1S whoop drones, featuring H.265 high-efficiency video coding technology, 1080P/60FPS image recording with 22ms ultra-low latency, and built-in 8 GB storage for interference-free HD video recording and USB exporting. Check out our other pre-built quads, as well as other great products from Flywoo! Features Redesigned canopy with enhanced aesthetics and reinforced camera protection. The bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter. Equipped with ROBO 1002 23,500KV motor and 1609 4-bladed 40mm propellers, delivers a 30% increase in power, flexible flight, and impressive speeds perfect for racing competitions. The GOKU Versatile F411 ELRS 1S AIO V2 boasts an ELRS 2.4G receiver, expertly connected via UART 2 instead of SPI for superior performance. A30 plug supports a continuous current of 15A, providing greater power and longer flight times compared to the PH2.0 connector. New battery compartment design allows for easy replacement of batteries of different models. Specification Motor: ROBO 1002 23500KV Electronic: GOKU Versatile F411 ELRS 1S 5A AIO V2.0 Props: 1609 - 4 blade 40mm 1.5mm Shaft HD Digital VTX System: Walksnail Avatar HD Mini 1S Lite Receiver: ExpressLRS 2.4GHz Weight: 33g Flight Time: Explorer 1S 450mAh HV V2: 4m - Explorer 1S 750mAh HV V2: 6m (approximate) Speed: 70km/h (approximate) GOKU Versatile F411 ELRS 1S 5A AIO V2.0Flight Controller MCU: STM32F411CEU6 GYRO: ICM42688 UARTS: 1/2 Soft serial port: 1 I2C: SCL/SDA BEC: 5V Input Voltage: 1S (<4.35v) Firmware: FLYWOOF411_5IN1_AIO Mounting: 25x25mm, M2 Onboard 4in1 ESC MCU: EFM8BB21 Power supply: 1S LiPo/LiPo HVCurrent: 5A Firmware: BLHeli_S Factory firmware: O_H_5_REV16_8.HEX Default protocol: DSHOT 150/300/600 ELRS 2.4G RX (UART2) Flywoo ROBO 1002 23500KV Fpv Motor: Configuration: 9N12P Stator Diameter: 10mm Stator Length: 2mm Shaft Diameter: 1.5mm Motor Dimension(Dia.xLen): Φ13.5x7.75mm Weight(g): 2.5(5cm wire) Idle current(5)@5V(A): 1.5 No.of Cells(Lipo): 1S Max Continuous Power(W)3S: 52 Internal Resistance: 75mΩ Max Current(3S): 14A Max Efficiency Current: (2-4A)>84% Walksnail Avatar HD Mini 1S Lite Model: Avatar mini 1s module Communication Frequency: 5.725-5.850GHz Transmitter Power (EIRP): FCC:<25.5dBm;CE:<14dBm;SRRC:<20dBm; MIC:<25dBm I/O Interface: JST1.0x6(Power in)JST1.0x4(USB) Mounting Holes: 25.5x25.5mm Dimensions: 30x30x6.5mm Storage: 8G Recording: 1080p/720p Weight: 5.1g Operating Temperature: -20-40℃ Channels: 8 Wide Power Input: 3.1V-5V Supported FC System: Betaflight OSD: Canvas mode Bitrate: 25mbps, 50mbps Latency Average delay: 22ms Antenna: IPEX Avatar lite camera Model: Avatar lite camera Image Sensor: 1/2.7”1nch Resolution: 1080P/60fps,720P/120fps,720P/60fps Ratio: 16/9 4/3 Lens:2.1mm FOV: 170° Aperture: F2.0 Shutter Rolling: Rolling shutter Min.Illumination: 0.001Lux Weight: 1.8g Dimensions: 14x14x16mm Includes 1x Flywoo BNF Firefly FR16 Nano Baby HD V2.0 1S 1.6" Micro Quad w/ Avatar Nano Cam - ELRS 2.4 GHz 4x 1609 - 4 40mm 1.5mm shaft 2x TPU Battery Mount 1x Hardware Screw Set 4x Prop guards
$239.99
RaceDayQuads Flywoo Explorer 3.8V 1S 450mAh 80C LiHV Battery 4 Pack - GNB27
All batteries must be shipped by a ground shipping method. Explorer series batteries are specially designed for long flight time and all are high voltage batteries. Using this battery will give you a significant increase in flight time as well as a bit more power over the stock battery. Check out our other 1S batteries, as well as the rest of our Flywoo selection! Specifications Nominal Voltage: 3.8V Cells: 1S Capacity: 450mAh Discharge Rate: 80C Composition: LiHV Discharge Lead: GNB27 30mm Dimensions: 59x18x6.8mm Weight: 13.2g Includes 4x Flywoo Explorer 4.35V 1S 450mAh 80C LiHV Battery - GNB27
$19.99
RaceDayQuads Flywoo Explorer V2 3.8V 1S 450mAh 80C LiHV Battery 4 Pack - A30
All batteries must be shipped by a ground shipping method. Explorer series batteries are specially designed for long flight time and all are high voltage batteries. Using this battery will give you a significant increase in flight time as well as a bit more power over the stock battery. Check out our other 1S batteries, as well as the rest of our Flywoo selection! Specifications Nominal Voltage: 3.8V Cells: 1S Configuration: 1S1P / 4.35V / 1 Cell Capacity: 450mAh Discharge Rate: 80C Composition: LiHV Weight: 13.2g Connector: A30 Includes 1x Flywoo Explorer 3.8V 1S 450mAh 80C LiHV Battery 4 Pack - A30
$22.99
RaceDayQuads Flywoo Explorer V2 3.8V 1S 750mAh 80C LiHV Battery 4 Pack - A30
All batteries must be shipped by a ground shipping method. Explorer series batteries are specially designed for long flight time and all are high voltage batteries. Using this battery will give you a significant increase in flight time as well as a bit more power over the stock battery. Check out our other 1S batteries, as well as the rest of our Flywoo selection! Specifications Nominal Voltage: 3.8V Cells: 1S Configuration: 1S1P / 4.35V / 1 Cell Capacity: 750Ah Discharge Rate: 80C Composition: LiHV Weight: 14g Connector: A30 Includes 1x Flywoo Explorer V2 3.8V 1S 450mAh 80C LiHV Battery 4 Pack - A30
$25.99
RaceDayQuads Flywoo GoPro 4.4V 1S 1220mAH Battery
This is a replacement battery for your GoPro. Check out our Flywoo selection. Specifications Weight: 22.5g Capacity: 1220mAH Dimensions: 30mm(L) x 10.8mm(W) x 35mm(H) Includes 1x Flywoo GoPro 4.4V 1S 1220mAH Battery
$19.99
RaceDayQuads Flywoo Pigtail A30-F 22AWG 80mm - 5 Pack
The A30 high current connectors are an ideal fit for high-performance drones, providing a reliable connection with minimal resistance. This 5-pack of A30 Pigtails has each measuring 80mm. Get improved performance and reliability with the ability of up to 15A of continuous current - far higher than the 4.5A of PH2.0 connectors. Discharging more current in the same capacity than PH2.0 crimped pins, A30 connectors provide significantly more power - leading to extended flight time at full throttle on 1S whoop drones. Upgrade to A30 connectors for better performance and reliability. Check out all our pigtails and connectors as well as our products from Flywoo! Flywoo factory images say 20awg, but 1st batch shipped are actually 22awg. Specifications Wire Length: 80mm Wire Gauge: 22AWG Weight: 1.2g (ea.) Connector: A30 Female Includes 1x Flywoo Pigtail A30-F 22AWG 80mm - 5 Pack
$5.99
RaceDayQuads Flywoo Robo 1002 19,800Kv Micro Motor
Replacement motor for the Firefly DC16 or a new motor to style out your next micro build with this purple and gold micro motor from Flywoo. Rated with a stator 1002 and Kv of 19,800, giving you great power for your whoop builds. Check out our Micro Motors and Flywoo gear selection! Specifications KV: 19800 Stator: 1002 Motor Bolt Pattern: 6mm Tri-Mount Configuration: 9N12P Stator Diameter: 10mm Stator Length: 2mm Shaft Diameter: 1.5mm Motor Dimension(Dia.xLen): Φ13.5x7.75mm Weight(g): 2.5(5cm wire) Idle current(5)@5V(A): 1.3 No.of Cells(Lipo): 1S Max Continuous Power(W)3S: 44 Internal Resistance: 89mΩ Max Current(3S): 11.8A Max Efficiency Current: (2-4A)>84% Includes 1x Flywoo Robo 1002 19800Kv Micro Motor
$12.99
RaceDayQuads Flywoo Robo 1002 23,500Kv Micro Motor
Replacement motor for the Firefly DC16 or a new motor to style out your next micro build with this purple and gold micro motor from Flywoo. Rated with a stator 1002 and Kv of 23,500, giving you great power for your whoop builds. Check out our Micro Motors and Flywoo gear selection! Specifications KV: 23500 Stator: 1002 Motor Bolt Pattern: 6mm Tri-Mount Configuration: 9N12P Stator Diamter: 10mm Stator Length: 2mm Shaft Diameter: 1.5mm Motor Dimension(Dia.xLen): Φ13.5x7.75mm Weight(g): 2.5(5cm wire) Idle current(5)@5V(A): 1.5 No.of Cells(Lipo): 1S Max Continuous Power(W)3S: 52 Internal Resistance: 75mΩ Max Current(3S): 14A Max Efficiency Current: (2-4A)>84% Includes 1x Flywoo Robo 1002 23500Kv Micro Motor
$12.99
RaceDayQuads FPV Cycle 13mm 11,400Kv Micro Motor
FPVCycle has the perfect addition to your little ripper with these fantastic micro motors. Check out our other FPVCycle motors, and all our FPV Cycle selection! Specifications Kv: 11400Kv Input Voltage: 1S LiPo Motor Dimensions: Φ17.5mm x 5.7mm Shaft Diameter: 2mm Mounting Pattern: Φ9mm Wire Dimensions: 27AWG x 200mm Weight (w/ wires): 6g Includes 1x FPV Cycle 13mm 11400Kv Micro Motor
$13.49
RaceDayQuads FPV Cycle BabyTooth Toothpick 3" Micro Frame Kit - 2mm
Use this frame in 1.5mm or 2mm with the 1S 3” drivetrain for a super fun and safe 45-55g AUW quad that will knock your socks off! The same pattern is offered in 3mm for the 3S drivetrain if you prefer a unibody over the TP3. It’s impressively stiff and confidence-inspiring in 3mm and only 8.8g. You should be aware that the 1.5mm version is not as strong as the 2mm version but it is about 1.3g lighter.This design is called the ‘Baby Tooth’ not because it’s smaller than the TP3, but because it supports 1S better and is simpler than the TP3. After some heavy refinement, this is the final pattern we landed on.This frame is cut from T700 carbon but It does not have a chamfer on it. This frame is supposed to be a high-value item with the majority of the design time invested into optimizing performance, weight, and durability. Customizing the frame with your own hand-done sanding on the edges is up to you.The latest version seen in the product pictures has thicker arm ends for more motor protection and a crossbar on one of the arms designed to mount the MiniMortal T antenna. The overall frame design has also had minor adjustments to its lines to improve durability further. Specifications: 115mm diagonal for 3” props T700 carbon 1.5mm thick ~4.4g (carbon only) 2mm thick 5.7g (carbon only) 3mm thick 8.8g (carbon only) Motor protection bumper FC Mounting: 25.4x25.4mm M2 (Whoop mount) FC Mounting: 16x16 M2 also on there Crossbar for mounting MiniMortal T Antenna FC mounting hardware included with frame Includes FPV Cycle Baby Tooth 2mm 3" Toothpick Frame Kit
$17.99
RaceDayQuads FPV Cycle Toothpick 3 (TP3) 3" Micro Frame Kit
At its inception, the Toothpick formula was to turn a whoop inside out and give it the ability to perform like a much larger craft. Just a typical brushless AIO whoop board with similar motors but very large, very light 65mm(2.5in) props on a very light frame. The resulting performance was jaw dropping in any configuration from an AUW of ~37g on 1S to 73g on 2S and pure wackiness on 3S.The goal with the Toothpick project was first and foremost to be safe for almost any environment, fully legal, quiet, durable, reliable and most importantly, loads of fun! These features should not be compatible with each other but the magic of crazy disk loading and power radios made it possible.As with anything, the more you do it, the more developed and fine tuned your tools become. Like a surgeon that gets better at their craft and graduates to more and more developed instruments, the TP3 is literally a refined, purpose built, surgical instrument of the sky. If built to top end spec on 3S, this sucker is a frikin bullet! So throw that safety out the window. However the same setup on 2S becomes a very safe friend :-). Just as safe as the original Toothpick setup. The noise profile on 2S is significantly quieter than a 65mm/2.5” Toothpick twin blade on 2S. On 3S it’s still slightly quieter than a top power spec 65mm/2.5” Toothpick.The TP3 formula is similar to the original. Extremely low weight, large props for such a low weight and the smallest motor that can spin that prop with good control. The pudding is in the details however and we spent months intensely testing everything just to find out that what we’re looking for doesn’t exist! So we started making custom parts. There is a lot in how it’s setup as well but that’s better left to the video than writing pages on pages...Starting with the prop, we knew what we wanted but it didn’t exist. Having a good relationship with Gemfan, we carefully crafted a prop together and they got working on manufacturing. With the prop in mind, we then tested custom motor products from just about every known company out there before landing on a couple of gems...that only became good with numerous revisions. Other manufacturers will figure it out and give us more options in time but the two we have now are stellar. Given the crazy performance we were after, the frame also needed to be reimagined to perform and hold up to a new level of punishment. Next, we had to solve the annoyance with whoop boards and how difficult they were to solder. FullSpeed and BetaFPV were instrumental in the execution of the redesign and we now have two great options in case one runs into QC or reliability issues. The rest of the build is arbitrary but we prefer just a basic camera and Vtx to keep the weight down. Performance wise, this thing is FAST. FAST fast. There are probably other things in this size class that are faster in a straight line, but that's not what we mean by fast. It’s like flying a laser pointer, it just does EXACTLY what you want it to do with absolute precision. Throttle control is also exquisite. It's a bit difficult to explain all the performance in words but when you fly one, you'll understand. The performance profile on a low weight load out also fits a Betaflight stock tune with just a little more TPA.Durability is one area that may be in question and is where we need to put a little bit of a disclaimer on this style build. When built to top spec on 3S, this thing is VERY FAST and INSANELY AGILE. This build is designed for advanced pilots but it doesn’t mean that it’s weak or not for beginners. That’s actually far from true. The frame is quite robust, motors are quality built and even the prop shaft is beefed up. When you first learn to ski or snowboard, you fall. You fall a LOT. It hurts. As you improve, you learn how to fall. Pro level athletes do amazing things and also know how to fall amazingly well. As an FPV pilot, you learn how not to break your equipment….or, balls to the wall and you know you’re going to break it and are okay with it. To achieve this level of performance, high durability has been replaced with repairability. It definitely still takes quite a bit of force to break an arm. The extremely low weight means that if you’re a beginner and running 2S, it’ll be quite difficult to break. It really only becomes a hazard to itself when you're darting around at high speeds.This thing is so incredibly easy to fly with its low weight and incredible control, it’s exactly what the advanced pilot needs to push their own limits and exactly what the novice wants to learn on. Check out all our 2-3" Frame Kits and the rest of our FPVCycle Collection Features Multi Unit design T700 carbon in 0.5mm laminate thickness (thinner is better, typical is 1.5mm) ~9-10g built frame base with hardware (some variation) 1.5mm body plates, 2.5mm arms Accepts 1”x1” typical whoop mounting platform Good quality carbon but no chamfers to keep costs down Made to be used. Not a shelf ornament. Every line on this design is very delicately crafted for optimization Repairability when you smash it Skinnier arms for less thrust deflection and rotational drag Similar weight to a monobody of the same or lesser durability Cheaper to maintain Easier to repair and maintain Doesn’t ruin your flying day due to a crash Recommendations Under 109g AUW with 3S 450mah Under 95g on 2S 450mah No smaller or larger than 450mah cells in 3S or 2S Press fit props on a 2mm prop shaft motor No more than ~7g per motor NO TPU SHOES ON THE ARMS! Includes 1x FPV Cycle Toothpick 3 3" Frame - TP3
$17.99
RaceDayQuads Fractal Engineering Fractal 65 Micro/Whoop Frame Kit - Choose Your Version
Are you a whoop racer seeking the best performance with no reliability sacrifice? An FPV pilot wanting a solid frame with fast maintenance? Or after a tough frame to keep you airborne, instead of flimsy nylon frames? If you answer yes to any of those, then the Fractal 65 was designed for you! This kit contains all you need to construct your craft - it's compatible with most parts and has a 25.5x25.5mm mount for the AIO and motor mounts for 3xM1.4x6.6mm and 3xM1.6x5.5. Choose between getting the Fractal 65 Whoop Micro Frame Lite Kit, which does not come with ducts, or grab a combo of the Fractal 65 Whoop Micro Frame kit and HappyModel Mobula6 Whoop frame. Note: You're gonna want to cut ducts from either an NBD, BetaFPV, or Happymodel 65mm whoop frame, and that will serve as your protection for your motor and propellers. This also allows you to replace a single duct where-as standard whoop frames need to be fully replaced when a single duct breaks. Check out our other Micro frames, and our Fractal Engineering Products! Features 65mm diagonal, squished X geometry, for 31mm props 1.5mm Carbon Fiber / Individual Nylon ducts hybrid construction Low-profile camera mount, no props in view, no tilt offset Low Center of gravity, by bringing the AIO closer to the frame/motors Allows mounting with USB pointing up for easy accelerometer calibration No need for a canopy as all electronics are tucked safely between the ducts Maximum rigidity where it matters most; connecting the motors to the FC Easy maintenance, break one duct, replace only the single duct Recommended Part List Gemfan Durable 1210 Bi-Blade 31mm Micro/Whoop Prop 8 Pack (1mm Shaft) Gemfan 1219-3 Durable Tri-Blade 31mm Micro/Whoop Prop 8 Pack (1mm Shaft) - Choose Your Color HappyModel EX 0802 19000Kv Whoop/Micro Motor for Mobula6 HD - CW HappyModel EX 0802 25000Kv Whoop/Micro Motor for Mobula6 HD - CW HappyModel RunCam Nano 3 800TVL CMOS FPV Camera w/ Holes & Plug for Mobula6 HappyModel Diamond 1S F4 AIO Flight Controller w/ 5A 8Bit 4in1 ESC & 400mW VTX - ELRS SPI HappyModel SuperBee F4 Lite AIO Whoop Flight Controller - Choose Version HappyModel CrossF4 F411 1-2S 5A 8Bit AIO Whoop Flight Controller - ELRS 2.4GHz FEA optimization test preformed ensuring the stress gets spread out across the whole structure without concentrations Specifications CF Weight: 1.6g Motor Bolt Pattern: 6mm Tri-Mount & 5.5mm Tri-Mount Stack Size: 25x25mm Includes 1x Fractal Engineering Fractal 65 Micro Frame Kit - Choose Your Version
$19.99
RaceDayQuads Fractal Engineering Fractal 65 Pro Micro/Whoop Frame Kit - Choose Your Version
Are you a whoop racer seeking the best performance with no reliability sacrifice? An FPV pilot wanting a solid frame with fast maintenance? Or after a tough frame to keep you airborne, instead of flimsy nylon frames? If you answer yes to any of those, then the Fractal 65 Pro was designed for you! This kit contains all you need to construct your craft - it's compatible with most parts and has a 25.5x25.5mm mount for the AIO and motor mounts for 3xM1.4x6.6mm and 3xM1.6x5.5. Choose between getting the Fractal 65 Pro Whoop Micro Frame Lite Kit, which does not come with ducts, or grab a combo of the Fractal 65 Pro Whoop Micro Frame Kit and Meteor65 Pro Whoop frame. Note: This is designed for prop guards that fit 35mm props like the Meteor65 Pro. This will serve as your protection and allows you to replace a single duct where-as standard whoop frames need to be fully replaced when a single duct breaks. The Pro version has been squished to the max to fit 35mm props with Meteor 65 Pro ducts. Check out our other Micro frames, and our Fractal Engineering Products! Features A variant of the Fractal 65 frame kit Squished to the max to fit 35mm props with Meteor 65Pro ducts Maintains 65mm motors distance to meet racing specs Still fits the camera between the front ducts 1.5mm Carbon Fiber / Individual Nylon ducts hybrid construction Low-profile camera mount, no props in view, no tilt offset Low Center of gravity, by bringing the AIO closer to the frame/motors Allows mounting with USB pointing up for easy accelerometer calibration No need for a canopy as all electronics are tucked safely between the ducts Maximum rigidity where it matters most; connecting the motors to the FC Easy maintenance, break one duct, replace only the single duct Recommended Part List BetaFPV Gemfan 1406 Tri-Blade 35mm Micro/Whoop Prop 4 Pack (1mm Shaft) - Choose Your Color HappyModel EX 0802 19000Kv Whoop/Micro Motor for Mobula6 HD - CW HappyModel EX 0802 25000Kv Whoop/Micro Motor for Mobula6 HD - CW HappyModel RunCam Nano 3 800TVL CMOS FPV Camera w/ Holes & Plug for Mobula6 HappyModel Diamond 1S F4 AIO Flight Controller w/ 5A 8Bit 4in1 ESC & 400mW VTX - ELRS SPI HappyModel SuperBee F4 Lite AIO Whoop Flight Controller - Choose Version HappyModel CrossF4 F411 1-2S 5A 8Bit AIO Whoop Flight Controller - ELRS 2.4GHz FEA optimization test performed, ensuring the stress gets spread out across the whole structure without concentrations Specifications CF Weight: 1.8g Motor Bolt Pattern: 6mm Tri-Mount & 5.5mm Tri-Mount Stack Size: 25x25mm Includes 1x Fractal Engineering Fractal 65 Micro Frame Kit - Choose Your Version
$20.99
RaceDayQuads Fractal Engineering Fractal 75 Micro/Whoop Frame Kit - Choose Your Version
Are you a whoop racer seeking the best performance with no reliability sacrifice? An FPV pilot wanting a solid frame with fast maintenance? Or after a tough frame to keep you airborne, instead of flimsy nylon frames? If you answer yes to any of those, then the Fractal 75 was designed for you! This kit contains all you need to construct your craft - it's compatible with most parts and has a 25.5x25.5mm mount for the AIO and motor mounts for 3xM1.4x6.6mm and 3xM1.6x5.5. Choose between getting the Fractal 75 whoop micro Frame Kit Lite Kit, which does not come with ducts, or grab a combo of the Fractal 75 Whoop Micro Frame Kit and HappyModel Mobula7 V4 Whoop frame. Note: You're gonna want to cut ducts from either an NBD, BetaFPV, or Happymodel 75mm whoop frame, and that will serve as your protection for you motor and propellers. This also allows you to replace a single duct where-as standard whoop frames need to be fully replaced when a single duct breaks. Check out our other Micro frames, and our Fractal Engineering Products! Features 75mm diagonal, squished X geometry, for 40mm props 1.5mm Carbon Fiber / Individual Nylon ducts hybrid construction. Cut from Japanese T300 CF sheet Low-profile camera mount, no props in view, no tilt offset Low Center of gravity, by bringing the AIO closer to the frame/motors Allows mounting with USB pointing up for easy accelerometer calibration No need for a canopy as all electronics are tucked safely between the ducts Maximum rigidity where it matters most; connecting the motors to the FC Easy maintenance, break one duct, replace only the single duct Lightweight, about 21g with HM DiamondF4 Recommended Parts List HappyModel Gemfan 1610 Bi-Blade 40mm Micro/Whoop Prop 4 Pack - Grey HappyModel RS 0802 20,000Kv Micro Motor - Choose Version HappyModel RunCam Nano 3 800TVL CMOS FPV Camera w/ Holes & Plug for Mobula6 HappyModel Diamond 1S F4 AIO Flight Controller w/ 5A 8Bit 4in1 ESC & 400mW VTX - ELRS SPI HappyModel SuperBee F4 Lite AIO Whoop Flight Controller - Choose Version HappyModel CrossF4 F411 1-2S 5A 8Bit AIO Whoop Flight Controller - ELRS 2.4GHz FEA optimization test performed, ensuring the stress gets spread out across the whole structure without concentrations Specifications CF Weight: 2.1g Motor Bolt Pattern: 6mm Tri-Mount & 5.5mm Tri-Mount Stack Size: 25x25mm Includes 1x Fractal Engineering Fractal 75 Micro Frame Kit - Choose Your Version
$22.99
RaceDayQuads Fractal Engineering Fractal 75 Pro Max Micro/Whoop Frame Kit - Choose Your Version
From motorpost to motorpost on this frame, the distance is 84mm. Are you a whoop racer seeking the best performance with no reliability sacrifice? An FPV pilot wanting a solid frame with fast maintenance? Or after a tough frame to keep you airborne, instead of flimsy nylon frames? If you answer yes to any of those, then the Fractal 75 Pro Max was designed for you! This kit contains all you need to construct your craft - it's compatible with most parts and has a 25.5x25.5mm mount for the AIO and motor mounts for 3xM1.4x6.6mm and 3xM1.6x5.5. Choose between getting the Fractal 75 Pro Max whoop micro Frame Lite Kit, which does not come with ducts, or grab a combo of the Fractal 75 Pro Max Whoop Micro-frame kit and BetaFPV Meteor75 Pro Whoop Frame. Note: This is designed for prop guards that fit 45mm props like the Meteor75 Pro. This will serve as your protection and allows you to replace a single duct where-as standard whoop frames need to be fully replaced when a single duct breaks. The Pro Version has been scaled to the max to fit 45mm props Check out our other Micro frames, and our Fractal Engineering Products! Features A completely new variant of the F75, but this is actually 84mm motorpost to motorpost distance. The same winning recipe, scaled to fit 45mm props with ducts while keeping the camera up front Extended camera mount to reduce prop guards in view Low center of gravity, by bringing the AIO close to the frame/motors Allows mounting with USB pointed up for easy accelerometer calibration Easy maintenance, break a duct, replace only the single duct No need for a canopy as all electronics are tucked safely between the ducts Approximately 21g using the Happymodel DiamondF4 AIO Recommended Parts List Gemfan Ducted 1815 Tri-Blade 45mm Micro/Whoop Prop 8 Pack (1.5mm Shaft) - Choose Your Color Gemfan Ducted 1815 Bi-Blade 45mm Micro/Whoop Prop 8 Pack (1.5mm Shaft) - Choose Your Color HappyModel RS 0802 20,000Kv Micro Motor - Choose Version HappyModel RunCam Nano 3 800TVL CMOS FPV Camera w/ Holes & Plug for Mobula6 HappyModel Diamond 1S F4 AIO Flight Controller w/ 5A 8Bit 4in1 ESC & 400mW VTX - ELRS SPI HappyModel SuperBee F4 Lite AIO Whoop Flight Controller - Choose Version HappyModel CrossF4 F411 1-2S 5A 8Bit AIO Whoop Flight Controller - ELRS 2.4GHz HappyModel OVX300 25-300mW 5.8GHz U.Fl VTX w/ OpenVTX FEA optimization test performed, ensuring the stress gets spread out across the whole structure without concentrations Specifications CF Weight: 2.21g Motor Bolt Pattern: 6mm Tri-Mount & 5.5mm Tri-Mount Stack Size: 25x25mm Includes 1x Fractal Engineering Fractal 75 Micro Frame Kit - Choose Your Version
$22.99
RaceDayQuads Fractal Engineering Fractal Wingman 1S 18650 Foldable 3" Micro Frame Kit
The first and only 3″ 1S 18650 quadcopter with foldable, soft-mounted arms and 20+ mins of flight time! Fractal Engineering's foldable take on the 18650 1S 3" long-range trend. Introducing the Wingman, a quad like this is more known for having a powerband more suited for cruising/exploration/surveillance than freestyle/racing. Though this is still very capable of freestyle, as shown in Infinity Loops video on this quad. Check out our other 3" frames, and our Fractal Engineering Products! Here's what Fractal has to say about this frame Have you ever wished you had an extra sidekick quad to help you recover your main machine from a tree? Or perhaps one you could deploy from the comfort of your car to recon a new spot without the hassle of going out and walking there? Or maybe just an ultra-compact video rig to give your loved one an excuse to rip a few packs under the pretense of documenting your vacation? Well, the Wingman is all of that, and much more! The idea for this frame stemmed from Dave C’s nano long-range, concept -obviously!- I was immediately hooked on the idea of being able to pop a single, general-purpose 18650 li-ion cell on a quad and cruise around longer than with any of my freestyle rigs Back then the only frame option was the original 3D printed one I knew I could greatly improve upon the concept by utilizing carbon fiber, but I also knew that by the time I would be ready to release, I wouldn’t be the only one with a CF arms nano LR So I decided to up it a notch; I’ve had this idea of folding arms in my head for a while, and the lightweight, low load use case of that format would be the best proving ground for it Over a year in the making, after many iterations and countless hours of testing and tuning later what is the result? The first-ever foldable and soft mounted arms in FPV The major unique feature of this frame kit is obviously the folding arms And the way it manages to achieve this feature in such an integrated manner is where the whole secret sauce resides This 3″ 1S format offers the possibility to push incredibly intricate ideas down to an incredibly simple execution thanks to the low prop load In this case, I’ve chosen to make the top and bottom plates clamped to the standoffs, While using the same standoffs as pivots for the arms, themselves sandwiched between 2 TPU shims and a nylon spacer to press them down in position Those TPU shims also serve 2 purposes at the same time; they primarily provide friction for the quick deployment of the arms, while also dampening the junctions This helps reduce the number of vibrations transmitted to the FPV and HD camera (more on that in a bit) and the FC gyro, enabling smooth footage and easy tuning Ultra-lightweight, durable and compact design The spaceframe carbon fiber body was meticulously designed to only keep material where absolutely necessary This includes protecting all the electronics and maintaining a rigid platform, While pocketing everything else for lightweight and airflow Making it only 24g frame only, or 60g ready to fly excl. battery Quick-release arm mechanism For being designed around ease of use and quick deployment, I went for a friction fit with a light detent to hold the arms open Just simply pull the arms out until the detent clicks, and push them back in when you’re done That means no manual latch, no thumbscrew, no positive lock This also means that in the event of a crash the arms might fold and you would need to go get it… …But you’re also more likely to be able to take off again without any damage, as I’ve found during testing that the folding appears to absorb a lot of energy that might have snapped something otherwise In any event, let that be clear that this remains a stable and soft cruiser above all; you won’t have much fun going bando bashing with it I can almost guarantee it To sum it up just a great tool to always have with you, just so many uses for it Toss it in your bag when you’re going on vacation for drone videos (also a great excuse for your wife to bring a quad) Use it to recon new spots to rip without going out of the car (walking? like with your legs?) Search and rescue! Take advantage of the long flight time to look for a lost quad (I hope you find it brother/sister) Attach a string to the back, fly around that branch you got your main quad stuck on, bring it back and give it a good tug (watch your head) Or even get that whoop you got stuck on that roof (I know you could just climb up the gutter but come on it’s 2022) Guerilla dive! pull it out of pocket, deploy it in a second, rip that huge building tower (you know which one), fold it back in your pocket and bail Or simply just cruise around for a relaxing chill flight, perhaps to wind down after a hard charger sesh (if you got the patience for it) … or whatever else you want it to be! Includes 1x Fractal Engineering Fractal Wingman 1S 18650 Foldable 3" Micro Frame Kit 1x Top plate 1x Bottom plate 2x Front plates 4x Arms 1x 18650 Tray 4x M2 x 10mm alu standoffs 4x M4 x 6mm nylon spacer 10x M2 x 5mm steel screw (for the standoffs) 4x M1.7 x 5mm steel self-threading screw (for the 18650 Tray) 1x TPU cam holder 2x TPU shim set 4x M2 x 10mm steel screw (for the stack) 10x M2 nylon nuts (for the stack) 10x M2 x 4mm socket screws (for the motors)
$41.99
RaceDayQuads Fractal Engineering Fractal Wingman 3" 2mm Replacement Arms Set (2pcs)
Replacement arm set for the Fractal Engineering Fractal Wingman 1S 18650 Foldable 3" Micro Frame Kit Check out all our Fractal Engineering Frames & Accessories and our Fractal Engineering Products! Specifications Weight: 1g ea. Arm thickness: 2mm Includes 1x Fractal Engineering Fractal Wingman 3" 2mm Replacement Arms Set (2pcs)
$4.99
RaceDayQuads Fractal Engineering HD Hardware set for F65/F75 and Wingman - Grommets + Screws
A set of custom-designed and printed, ultra-soft TPE grommets to fit both your whoop AIO and your VTX in a most compact way (8.5mm tall) Fits HDZero, Walksnail, naked Vista, etc… These parts are for the Fractal Engineering Fractal 65 Micro/Whoop Frame Kit and Fractal Engineering Fractal 75 Micro Whoop Frame Kit, and Fractal Engineering Fractal Wingman 1S 18650 Foldable 3" Micro Frame Kit. Check out all our Fractal Engineering Frames & Accessories and our Fractal Engineering Products! Includes 1x Fractal Engineering HD Hardware set for F65/F75 and Wingman - Grommets + Screws
$3.99
RaceDayQuads Fractal Engineering Whoop Juice Transfer Station 1S Balance Board
The best way to charge, discharge, and storage charge your 1S lipos! Are you sick and tired of cheap 1S lipo chargers with limited functionally and often inaccurate calibration? Then look no further than the whoop juice transfer station! There is a jumper so you don’t have to populate all 6 ports to close the balance circuit. Allows you to charge six 1S batteries with most smart chargers as a 6S battery. Meaning you do not have to match the voltage for each battery when starting the process. Check out our other charging accessories, and our Fractal Engineering Products! Features The PCB board I designed from thick traces, copper filled on both sides for thermal dissipation The VIN and balance leads are assembled from 100mm, silicone wires, and genuine Amass XT60 It comes with extended, red jumpers for easy swapping cell count Includes 1x Fractal Engineering Whoop Juice Transfer Station 1S Balance Board
$12.99
RaceDayQuads Gaoneng GNB 3.7V 1S 450mAh 80C LiHV Whoop/Micro Battery w/ Plastic Head - PH2.0
All batteries must be shipped by a ground shipping method. The Gaoneng GNB 3.7V 1S 450 mAh 80C LiHV Battery is the perfect solution for your 1S quads. Boasting a capacity of 450 mAh and a discharge rate of 80C, it provides reliable, efficient power with a long flight time. With a PH2.0 connector, you can count on secure, reliable connections and minimal resistance. Check out our other 1S packs and our selection of Gaoneng Products! Specifications Model No.: GNB4501S80PHV Capacity: 450mAh Voltage: 3.8V (LiHV) Cells Configuration: 1S1P Pack Dimension: 6.5x17x60mm (HxWxL) Net Weight: 12g (+/-1g) Discharge Rate: 80C Charge Rate: 1C to 5C Discharge and Charge Connector: PH2.0 Includes 1x Gaoneng GNB 3.7V 1S 450mAh 80C LiHV Whoop/Micro Battery w/ Plastic Head - PH2.0
$3.99
RaceDayQuads Gaoneng GNB 3.7V 1S 450mAh 80C LiPo Whoop/Micro Battery (Long Type) w/ Cabled - PH2.0
All batteries must be shipped by a ground shipping method. The Gaoneng GNB 3.7V 1S 450 mAh 80C LiPo Battery is the perfect solution for your 1S quads. Boasting a capacity of 450 mAh and a discharge rate of 80C, it provides reliable, efficient power with a long flight time. With a PH2.0 connector, you can count on secure, reliable connections and minimal resistance. Check out our other 1S packs and our selection of Gaoneng Products! Specifications Model No.: GNB4501S80AA Capacity: 450mAh Voltage: 3.7V Cells Configuration: 1S1P Pack Dimension: 6x17x59mm (HxWxL) Net Weight: 12g (+/-1g) Discharge Rate: 80C Charge Rate: 1C to 5C Discharge and Charge Connector: PH2.0 Includes 1x Gaoneng GNB 3.7V 1S 450mAh 80C LiPo Whoop/Micro Battery (Long Type) w/ Cabled Connector - PH2.0
$3.99
RaceDayQuads Gaoneng GNB 3.7V 1S 450mAh 80C LiPo Whoop/Micro Battery w/ Plastic Head - PH2.0
All batteries must be shipped by a ground shipping method. The Gaoneng GNB 3.7V 1S 450 mAh 80C LiPo Battery is the perfect solution for your 1S quads. Boasting a capacity of 450 mAh and a discharge rate of 80C, it provides reliable, efficient power with a long flight time. With a PH2.0 connector, you can count on secure, reliable connections and minimal resistance. Check out our other 1S packs and our selection of Gaoneng Products! Specifications Model No.: GNB4501S80P Capacity: 450mAh Voltage: 3.7V Cells Configuration: 1S1P Pack Dimension: 6x17x59mm (HxWxL) Net Weight: 12g (+/-1g) Discharge Rate: 80C Charge Rate: 1C to 5C Discharge and Charge Connector: PH2.0 Includes 1x Gaoneng GNB 3.7V 1S 450mAh 80C LiPo Whoop/Micro Battery w/ Plastic Head - PH2.0
$4.29
RaceDayQuads Gaoneng GNB 3.7V 1S 550mAh 90C LiPo Whoop/Micro Battery w/ Cabled - A30
The Gaoneng GNB 3.7V 1S 550 mAh 90C LiPo Battery is the perfect solution for your 1S quads. Boasting a capacity of 550 mAh and a discharge rate of 90C, it provides reliable, efficient power with a long flight time. With an A30 connector, you can count on secure, reliable connections and minimal resistance. Check out our other 1S packs and our selection of Gaoneng Products! Specifications Capacity: 550mAh Voltage: 3.7V Cells Configuration: 1S1P Pack Dimension: 6x18x66mm (HxWxL) Net Weight: 14g (+/-1g) Discharge Rate: 90C Charge Rate: 1C to 5C Discharge and Charge Connector: A30 Includes 1x Gaoneng GNB 3.7V 1S 550mAh 90C LiPo Whoop/Micro Battery w/ Cabled - A30
$4.79
RaceDayQuads Gaoneng GNB 3.7V 1S 550mAh 90C LiPo Whoop/Micro Battery w/ Plastic Head - A30
The Gaoneng GNB 3.7V 1S 550 mAh 90C LiPo Battery is the perfect solution for your 1S quads. Boasting a capacity of 550 mAh and a discharge rate of 90C, it provides reliable, efficient power with a long flight time. With an A30 connector, you can count on secure, reliable connections and minimal resistance. Check out our other 1S packs and our selection of Gaoneng Products! Specifications Capacity: 550mAh Voltage: 3.7V Cells Configuration: 1S1P Pack Dimension: 6x18x65mm (HxWxL) Net Weight: 13.5g (+/-1g) Discharge Rate: 90C Charge Rate: 1C to 5C Discharge and Charge Connector: A30 Includes 1x Gaoneng GNB 3.7V 1S 550mAh 90C LiPo Whoop/Micro Battery w/ Plastic Head - A30
$4.79
RaceDayQuads Gaoneng GNB 3.8V 1S 300mAh 60C LiHV Whoop/Micro Battery w/ Plastic Head - PH2.0
All batteries must be shipped by a ground shipping method. The Gaoneng GNB 3.8V 1S 300 mAh 60C LiHV Battery is the perfect solution for your 1S quads. Boasting a capacity of 300 mAh and a discharge rate of 60C, it provides reliable, efficient power with a long flight time. With a PH2.0 connector, you can count on secure, reliable connections and minimal resistance. Check out our other 1S packs and our selection of Gaoneng Products! Specifications Model No.: GNB3001S60WHV Capacity: 300mAh Voltage: 3.8V (LiHV) Cells Configuration: 1S1P Pack Dimension: 6.5x11.5x50mm (HxWxL) Net Weight: 7g (+/-0.5g) Discharge Rate: 60C Charge Rate: 1C to 5C Discharge and Charge Connector: PH2.0 Includes 1x Gaoneng GNB 3.8V 1S 300mAh 60C LiHV Whoop/Micro Battery w/ Plastic Head - PH2.0
$2.99
RaceDayQuads Gaoneng GNB 3.8V 1S 300mAh 60C LiHV Whoop/Micro Battery w/ Cabled - PH2.0
All batteries must be shipped by a ground shipping method. The Gaoneng GNB 3.8V 1S 300 mAh 60C LiHV Battery is the perfect solution for your 1S quads. Boasting a capacity of 300 mAh and a discharge rate of 60C, it provides reliable, efficient power with a long flight time. With a PH2.0 connector, you can count on secure, reliable connections and minimal resistance. Check out our other 1S packs and our selection of Gaoneng Products! Specifications Model No.: GNB3001S60WHV Capacity: 300mAh Voltage: 3.8V (LiHV) Cells Configuration: 1S1P Pack Dimension: 6.5x11.5x50mm (HxWxL) Net Weight: 7g (+/-0.5g) Discharge Rate: 60C Charge Rate: 1C to 5C Discharge and Charge Connector: PH2.0 Includes 1x Gaoneng GNB 3.8V 1S 300mAh 60C LiHV Whoop/Micro Battery w/ Cabled Connector - PH2.0
$2.99
RaceDayQuads Gaoneng GNB 3.8V 1S 300mAh 80C LiHV Whoop/Micro Battery w/ Plastic Head - PH2.0
All batteries must be shipped by a ground shipping method. The Gaoneng GNB 3.8V 1S 300 mAh 80C LiHV Battery is the perfect solution for your 1S quads. Boasting a capacity of 300 mAh and a discharge rate of 80C, it provides reliable, efficient power with a long flight time. With a PH2.0 connector, you can count on secure, reliable connections and minimal resistance. Check out our other 1S packs and our selection of Gaoneng Products! Specifications Model No.: GNB3001S80PHV Capacity: 300mAh Voltage: 3.8V (LiHV) Cells Configuration: 1S1P Pack Dimension: 6x17x48mm (HxWxL) Net Weight: 8.5g (+/-1g) Discharge Rate: 80C Charge Rate: 1C to 5C Discharge and Charge Connector: PH2.0 Includes 1x Gaoneng GNB 3.8V 1S 300mAh 80C LiHV Whoop/Micro Battery w/ Plastic Head - PH2.0
$3.99
RaceDayQuads Gaoneng GNB 3.8V 1S 300mAh 80C LiHV Whoop/Micro Battery w/ Cabled - PH2.0
All batteries must be shipped by a ground shipping method. The Gaoneng GNB 3.8V 1S 300 mAh 80C LiHV Battery is the perfect solution for your 1S quads. Boasting a capacity of 300 mAh and a discharge rate of 80C, it provides reliable, efficient power with a long flight time. With a PH2.0 connector, you can count on secure, reliable connections and minimal resistance. Check out our other 1S packs and our selection of Gaoneng Products! Specifications Model No.: GNB3001S80PHV Capacity: 300mAh Voltage: 3.8V (LiHV) Cells Configuration: 1S1P Pack Dimension: 6x17x48mm (HxWxL) Net Weight: 8.5g (+/-1g) Discharge Rate: 80C Charge Rate: 1C to 5C Discharge and Charge Connector: PH2.0 Includes 1x Gaoneng GNB 3.8V 1S 300mAh 80C LiHV Whoop/Micro Battery w/ Cabled Connector - PH2.0
$3.49
RaceDayQuads Gaoneng GNB 3.8V 1S 380mAh 90C LiHV Whoop/Micro Battery w/ Cabled - A30
All batteries must be shipped by a ground shipping method. The Gaoneng GNB 3.8V 1S 380 mAh 90C LiHV Battery is the perfect solution for your 1S quads. Boasting a capacity of 380 mAh and a discharge rate of 90C, it provides reliable, efficient power with a long flight time. With an A30 connector, you can count on secure, reliable connections and minimal resistance. Check out our other 1S packs and our selection of Gaoneng Products! Specifications Capacity: 380mAh Voltage: 3.8V (LiHV) Cells Configuration: 1S1P Pack Dimension: 6.7x17x50mm (HxWxL) Net Weight: 10g (+/-1g) Discharge Rate: 90C Charge Rate: 1C to 5C Discharge and Charge Connector: A30 Includes 1x Gaoneng GNB 3.8V 1S 380mAh 90C LiHV Whoop/Micro Battery w/ Cabled - A30
$4.29
RaceDayQuads Gaoneng GNB 3.8V 1S 380mAh 90C LiHV Whoop/Micro Battery w/ Cabled - PH2.0
All batteries must be shipped by a ground shipping method. The Gaoneng GNB 3.8V 1S 380 mAh 90C LiHV Battery is the perfect solution for your 1S quads. Boasting a capacity of 380 mAh and a discharge rate of 90C, it provides reliable, efficient power with a long flight time. With a PH2.0 connector, you can count on secure, reliable connections and minimal resistance. Check out our other 1S packs and our selection of Gaoneng Products! Specifications Model No.: GNB3801S90WHV Capacity: 380mAh Voltage: 3.8V (LiHV) Cells Configuration: 1S1P Pack Dimension: 7x17x50mm (HxWxL) Net Weight: 10g (+/-1g) Discharge Rate: 90C Charge Rate: 1C to 5C Discharge and Charge Connector: PH2.0 Includes 1x Gaoneng GNB 3.8V 1S 380mAh 90C LiHV Whoop/Micro Battery w/ Cabled Connector - PH2.0
$2.25
RaceDayQuads Gaoneng GNB 3.8V 1S 380mAh 90C LiHV Whoop/Micro Battery w/ Plastic Head - A30
All batteries must be shipped by a ground shipping method. The Gaoneng GNB 3.8V 1S 380 mAh 90C LiHV Battery is the perfect solution for your 1S quads. Boasting a capacity of 380 mAh and a discharge rate of 90C, it provides reliable, efficient power with a long flight time. With an A30 connector, you can count on secure, reliable connections and minimal resistance. Check out our other 1S packs and our selection of Gaoneng Products! Specifications Capacity: 380mAh Voltage: 3.8V (LiHV) Cells Configuration: 1S1P Pack Dimension: 6.7x17x49mm (HxWxL) Net Weight: 10g (+/-0.7g) Discharge Rate: 90C Charge Rate: 1C to 5C Discharge and Charge Connector: A30 Includes 1x Gaoneng GNB 3.8V 1S 380mAh 90C LiHV Whoop/Micro Battery w/ Plastic Head - A30
$4.45
RaceDayQuads Gaoneng GNB 3.8V 1S 380mAh 90C LiHV Whoop/Micro Battery w/ Plastic Head - PH2.0
All batteries must be shipped by a ground shipping method. The Gaoneng GNB 3.8V 1S 380 mAh 90C LiHV Battery is the perfect solution for your 1S quads. Boasting a capacity of 380 mAh and a discharge rate of 90C, it provides reliable, efficient power with a long flight time. With a PH2.0 connector, you can count on secure, reliable connections and minimal resistance. Check out our other 1S packs and our selection of Gaoneng Products! Specifications Model No.: GNB3801S90PHV Capacity: 380mAh Voltage: 3.8V (LiHV) Cells Configuration: 1S1P Pack Dimension: 6.5x17x48mm (HxWxL) Net Weight: 9.5g (+/-1g) Discharge Rate: 90C Charge Rate: 1C to 5C Discharge and Charge Connector: PH2.0 Includes 1x Gaoneng GNB 3.8V 1S 380mAh 90C LiHV Whoop/Micro Battery w/ Plastic Head - PH2.0
$3.99
RaceDayQuads Gaoneng GNB 3.8V 1S 450mAh 80C LiHV Whoop/Micro Battery w/ PH2.0
All batteries must be shipped by a ground shipping method. GNB Series Lipos are known and loved by the community for their strong performance. Check out our 1S battery selection and our selection of Gaoneng Products! Specifications Capacity: 450mAh Continuous Discharge Rate: 80C Dimensions: 59.6x18.4x6.9mm Discharge Lead: 12mm Weight: 13.3g (+/- 1%) Includes 1x Gaoneng 3.8V 1S 450mAh 80C LiHV Whoop/Micro Battery w/ PH2.0
$4.29
RaceDayQuads Gaoneng GNB 3.8V 1S 530mAh 90C LiHV Whoop/Micro Battery - XT30
All batteries must be shipped by a ground shipping method. The Gaoneng GNB 3.8V 1S 530mAh 90C LiHV Battery is the perfect solution for your 1S quads. Boasting a capacity of 530mAh and a discharge rate of 90C, it provides reliable, efficient power with a long flight time. Including an XT30 connector ensures a secure connection, delivering reliable and consistent power. Check out our other 1S packs and our selection of Gaoneng Products! Specifications Model No.: GNB5301S90AHV Capacity: 530mAh Voltage: 3.8V (LiHV) Cells Configuration: 1S1P Pack Dimension: 6.1x17x59mm (HxWxL) Net Weight: 13g (+/-1g) Discharge Rate: 90C Charge Rate: 1C to 5C Discharge and Charge Connector: XT30 Includes 1x Gaoneng GNB 3.8V 1S 530mAh 90C LiHV Whoop/Micro Battery w/ Cabled Connector - XT30
$4.49
RaceDayQuads Gaoneng GNB 3.8V 1S 530mAh 90C LiHV Whoop/Micro Battery w/ Cabled - A30
All batteries must be shipped by a ground shipping method. The Gaoneng GNB 3.8V 1S 530mAh 90C LiHV Battery is the perfect solution for your 1S quads. Boasting a capacity of 530 mAh and a discharge rate of 90C, it provides reliable, efficient power with a long flight time. With an A30 connector, you can count on secure, reliable connections and minimal resistance. Check out our other 1S packs and our selection of Gaoneng Products! Specifications Capacity: 530mAh Voltage: 3.8V (LiHV) Cells Configuration: 1S1P Pack Dimension: 61x17.5x6.5mm (HxWxL) Net Weight: 12g (+/-1g) Discharge Rate: 90C Charge Rate: 1C to 5C Discharge and Charge Connector: A30 Includes 1x Gaoneng GNB 3.8V 1S 530mAh 90C LiHV Whoop/Micro Battery w/ Cabled - A30
$4.89
You have seen 96 out of 219 products