The Plug and Play Argus is AxisFlying electronic series that includes ESC, FC, and stack.  Argus PRO series adopt a full aluminum cover wrapped that can get IP54 to protect PCB.  Argus series is PCB electronic only. There are 2 kinds of ESC 55A and 65A. The FC is F722 that can support X8  Check out all our 30x30 FC Stacks, and all our Axis Flying Products! Specifications Argus F722 Flight Controller MCU: STM32F722RET6 Gyro: BMI270 Barometer: Yes OSD: Yes BEC: 9V/2A, 5V/2A UART Ports: 6 Black Box: 16MB onboard Number of supported motors: 8 Firmware Name: AXISFLYINGF7PRO Input Voltage: 3-6S LiPo  Installation Holes: 30.5x30.5mm M3 32bit 4in1 ESC Continuous Current: 65A Burst Current: 75A Input Voltage: 3-6S ESC Target: BLHeli_32 (ST_G0_04) Current Proportion value: Scale=400 PWM Frequency Range: 16-96khz Telemetry: Supported Ammeter: Supported BEC: No Installation holes: 30.5x30.5mm Dimensions: 48.6x44x6.3mm Weight: 16.2g Includes 1x AxisFlying Argus F722 3-6S 30x30 Stack/Combo (F7 FC / 32bit 65A 4in1 ESC) 1x Wiring Set  

Read more less

DarwinFPV Betaflight F4 Flight Controller and 2-6S BLHeli_S 4in1 Dshot600 ESC Stack with 50A continuous current and Dshot600 weighing only 10.8g!  Check out our other AIO Flight Controllers and our Darwin FPV products! Specifications F405 MCU: STM32F405 Gyro: MPU6000 OSD Chip: Betaflight OSD AT7456E Blackbox: 16MB UARTS: 5 I2C: SDA / SLA pads LED: Yes Beeper: Yes Firmware Target: MATEKF405 FC Mounting Pattern: 30x30mm Dimensions: 37x36x10.8mm 4in1 ESC Input Voltage: 2-6S Max. Continuous Current: 50A Max. Burst Current: 60A  MCU: EFM8BB21F16G BEC: 5V/2A  Current Sensor: No Mounting Dimensions: 30x30mm(M3) Dimensions 37x36x10.8mm Includes 1x Darwin FPV F405 2-6S 30x30 Stack/Combo (F405 FC/50A 8bit 4in1 ESC) Wiring Diagram

Read more less

This stack pairs the Mamba MK4 F722 APP FC and the Mamba F55_128k 55A 4in1 ESC. With multiple UARTS and BECS, this stack can run all the peripherals you could ever want with ease. Browse our Stacks & Combos and our Diatone Gear! Specifications Mamba MK4 F722 APP Voltage Input: 3-6S MCU: STM32F722 Gyro: ICM42688P OSD: AT7456E Blackbox: 16M Flash Memory Uarts: 6Set ESC Signal: 8Set LED Controller: BF LED/MB LED I2C: Yes F.Port: Yes Buzz: Yes WiFi: Yes TVS Protection: Yes BEC: 3.3V 0.5A & 5V 3A & 9V 3A Mounting Pattern: 30x30 M3 Mamba F55 128k Input Voltage: 3~6S Lipo (12.6V~25.2V) Max Continuous Current: 55A Max Burst Current: 65A  BEC: No Target：BLHeli_32 MAMBA F55_128K Protocol: Dshot300/600/1200 PWM Range: 24~128K TVS Protection: Yes Mounting Pattern: 30x30 M3 Includes 1x Diatone Mamba MK4 F722 APP F55_128k 3-6S 30x30 Stack/Combo (F722 FC / 55A 128k 32bit 4in1 ESC) Wiring Diagram

Read more less

Diatone has released their 4th generation F722 mini stack. The MK4 F722 mini 20x20 stack boasts larger soldering pads, wider pad spacing, more UARTs, l2C and is configurable through the Speedy Bee App via built-in Wi-Fi! So much power from a lightweight stack!  Browse our Stacks & Combos and our Diatone Gear! Features The pad area increased by 30% Pad spacing increased by 100% MP9943 synchronous rectifier BEC MINI series upgrade DJI interface and 5v 15W/9V 18W 2 set BEC USB Type C 6 Set UART and I2C 4 Set Power Protection 32Bit ESC all support 128K Mini series FC uses 2mm and 3mm mounting holes, w/ a special dampening ring Upgrade the twisted pair anti-jamming cable and reinforcement process Specifications Mamba Basic Mini F722 MK4 Input: 2-6S MCU: ICM42688P Barometer: Yes OSD: Yes Blacbox: 16M Flash Memory Uarts: 6Set Protocol: Dshot300/600/1200 ESC Telemetry: Yes Power Led: Yes LED Controller: BF LED F.Port: Yes Buzz: Yes TVS Protection: Yes BEC: 3.3V 0.5A & 5V 2.5A Mounting Pattern: 20x20 M3/M2 Mamba F40 128k Input Voltage: 3-6S Lipo  Max Continuous Current: 40A Max Burst Current: 45A  BEC: No Target：BLHeli_32 MAMBA F40_128K_MINI Protocol: Dshot300/600/1200 PWM Range: 24~128K TVS Protection: Yes Mounting Pattern: 20x20 M2/M3 Includes 1x Diatone Mamba Basic MK4 F722 Mini F40_128k 2-6S 20x20 Stack/Combo 5x M2 Silicone Grommets 5x M3 Silicone Grommets 5x M2 ESC Isolation Columns 5x M3 ESC Isolation Columns 1x 8 Pin single-ended cable for flight controller 2x 8 Pin Cable 1x 6 Pin Air Unit Cable 1x XT60 1x Capacitor Wiring Diagram

Read more less

With an already impressive lineup of flight controllers, Flywoo has released the GOKU GN405 Nano. An economical and durable stack, the GN405 is packed with features including a barometer, 16MB black box, 6 complete hardware serial ports, I2C functionality, and WS2812 LEDs on each corner. It is specifically designed to be pin mounted to the GOKU BS13A / 35A 4-in-1 16x16 ESCs but can also be soldered via pads. The programmable WS2812 LED on each corner provides low-profile lighting for this tiny FC Check out all our 16x16 stacks, and our Flywoo gear selection! Specifications GN405 NANO FC Dimensions: 22x22mm Weight: 2.3g Mounting Pattern: 16x16, M3 Holes MCU: STM32F405 BGA UARTS: 6 1/2/3/4/5/6 I2C: SCL/SDA GYRO: ICM42688 BARO: BMP280 BEC: 5V 2A LED: 4x WS2812 FLASH: 8M Input Voltage: 2-6S Firmware: FLYWOOF405NANO BS13A 4-IN-1 ESC Support: Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600 Input Voltage: 2-4S Lipo Continuous Current: 13A Firmware: BLHELI_S Mounting Pattern: 16x16mm Weight: 2.5g Includes 1x GOKU GN405 &  BS13A 2-4S 16x16 Stack/Combo   Wiring Diagram

Read more less

This is a unique stack for the demands of the industry today. It has a 25.5x25.5 M2 (Whoop) mount pattern because there are now many frames that are designed with that pattern. The problem is that high-powered AIO boards are way overpriced due to the forever chip shortage and still have a high failure rate. Much of the failures are associated with the cramped space constraints of the small board. We split the ESC and FC but called for the ESC to have a nearly empty top side and the FC to have nearly all its components on the bottom and sit inside the footprint of the ESC solder pads. ALL of the FC's solder pads are also on the TOP. When you assemble the stack inside your frame, you will be able to access and solder ALL pads on BOTH boards. Additionally, the FC has a black box chip which is rare on AIO boards. Check out our other AIO Flight Controllers and our Darwin FPV products! Specifications F722 MCU: STM32F722RET6(216MHz) Gyro: MPU6000 Barometer: BMP280(I2C) OSD Chip: Betaflight OSD AT7456E Blackbox: 16MB UARTS: 5 I2C: SDA / SLA pads LED: Yes Beeper: Yes Firmware Target: DARWINF722HD FC Mounting Pattern: 25.5x25.5mm Dimensions: 37x36x10.8mm 4in1 ESC Input Voltage: 3-6S Max. Continuous Current: 50A Max. Burst Current: 60A  MCU: EFM8BB21F16G BEC: 5V/2A and 10V/2A Current Sensor: Yes (Scale 125) Mounting Dimensions: 25.5x25.5mm(M2) Dimensions 37x36x10.8mm Includes 1x FPV Cycle Darwin FPV F722 25x25 Flight Controller 1x FPV Cycle Darwin FPV 45A 3-6S 25x25 4in1 ESC 1x XT60-7CM-14AWG Power cables 1x 25V 470uF capacitor 8 x M2*6.5mm Damping rings 4 x M2 nuts Wiring Diagram

Read more less

Check out this fantastic budget stack brought to you by HGLRC, which is 2S-6S capable and can confidently handle 60 amps of power. (70 Burst) Boasting an MP6000 for precise and reliable performance from your flight controller.  The SPECTER F460 is an excellent choice for your next 5-6" build!  Check out our other 30x30 Stacks, and all our HGLRC products! Features The flight control adopts the extremely stable MPU6000 gyroscope; The flight control main control chip adopts F405 chip, and the serial port supports up to 4 groups, with fast operation speed and smoother control; The main chip of the ESC selects a new imported FD6288 processor, which is matched with ON3109 high-performance MOS, and can continuously withstand current and stabilize output; It can be quickly connected to the camera/receiver/image transmission/LED/GPS through the socket, no welding required; Maximum support for BEC 9V2A/BEC 5V2.5A, which can provide stable voltage and current output to external devices; Immersion gold high-tech design is temperature-resistant and current-resistant, the ESC has a large pad, and the flight controller is directly plugged in, so there is no trouble in welding; Integrated 16M black box, can record flight data; Onboard galvanometer module, real-time viewing of data such as current feedback through the flight control;   Specifications Input Voltage: 2-6S Lipo (7.4V-22.8V) Installing Hole: 30.5x30.5mm, M3 Support Protocols :DShot600/300/150/Oneshot125/42,MultiShot Weight:29g SPECTER F405 FC MCU: STM32F405 GYRO: MPU6000 OSD: AT7456E Blackbox: 16MB UART: 4 BEC: 9V2A/5V2.5A FC Firmware: HGLRCF405V2 Size: 38mmx38mm SPECTER 60A ESC Constant Current: 60A Peak Current: 70A（10s） ESC Firmware: BL_S (J-H-30) Size: 37x42.7mm Includes 1x HGLRC SPECTER F460 HD 2-6S 30x30 Stack/Combo (F4 FC / 8Bit 60A 4in1 ESC) - MPU6000

Read more less

The Hobbywing XRotor F722 Stack/Combo packs in the latest tech: 65A (x4) ESCs, BLHeli_32 DShot 1200 support, two 5V BECs, plus a voltmeter module that lets your FC know your battery's voltage and amperage in real-time! The F7 Flight Controller offers OSD, voltage monitoring, two BECs, and an interface for the DJI image transmission system. Build the perfect multirotor with this feature-packed, powerful combo!  Check out all our 30x30 stacks & combos, and our Hobbywing selection! Features Manual for the FC Manual for the ESC XRotor 65A 4in1 ESC High performance 32-bit microprocessor with the running frequency of up to 120MHz for excellent performance. Third generation BLHeli_32 code can support up to 128KHz PWM output frequency, which can be compatible with more motors. All codes use damped light mode. Damped light does regenerative braking, causing very fast motor retardation, and inherently also does active freewheeling. Code supports features to prevent sync loss. There are tunable parameters that can make the code run well even in the most demanding situations, although default settings will work excellently in normal operating environments. The code supports regular 1-2ms pulse width input, as well as Oneshot125 (125-250us), Oneshot42 (41.7-83.3us) and Multishot (5-25us). Dshot signaling is supported at any rate up to at least Dshot1200. The input signal is automatically detected by the ESC upon power up. Also supports a beacon functionality, where the ESC will start beeping after a given time of zero throttle. This can be very useful for finding lost aircraft. F7 Flight Controller Features STM32 F722 MCU allows the FC to run the PID looptime and gyro with higher frequency. Onboard OSD microchip which supports the DMA mode allows users to adjust its parameters via the Betaflight software. (Note: the OSD is controlled by the F4 MCU.) The FC supports Betaflight firmware and allows parameter adjustment via Betaflight software is more applicable to FPV racing. Onboard Flash chip can record and save flight/black box data allowing users to adjust the setup of their aircraft easily. Compatible with various receivers like SBUS, SUMH, SUMD, SPEKTRUM1024/2048, XBUS and etc. LED strip signal output port allows users to adjust the color and flash mode of the LED strip via the FC. Volt/Amp monitoring port allows users to check the battery voltage (BAT port) and current (CRT port, extra current meter is needed). Buzzer output port allows users to connect external buzzer(s) to the FC for warning or informing the flight status of the aircraft. Micro USB port allows users to connect the FC to a PC to flash firmware and adjust parameters. Board load 5V and 10V BEC, both can output 2A. It can supply power for receiver, VTX, LED lamp and others devices.  Specifications XRotor F7 FC Compatible with (Multirotors) Quadcopters Firmware HOBBYWING_XROTORF7CONV FC Programming Supported Programming via Betaflight/ Cleanflight-configurator Compatible with (Modes) PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600, PROSHOT1000 Compatible with (Transmitters) PPM, Spektrum, SBUS, SUMD, SUMH, XBUS, IBUS, JETIEXBUS, CRSF, SRXL OSD Built-in Voltage Monitoring Supported Current Monitoring Supported External Buzzer Supported LED Control Supported BEC 5V @ 1.5A ; 10V @ 1.5A Size 32x32mm Weight 3.3g XRotor 65A BLHeli_32 ESC LiPo Power input: 3-6S Cont.Current: 65Ax4 Burst Current: 80Ax4 BEC Output: 5V@ 0.5A Input wires: 12AWG-130mm* (Red/Black) Output Wire: No wires but solder tabs Connectors: (In/Out) XT60 (w/ Wires Soldered on) /no Weight / Size: 15.0g / 32.7x18.4x6.2mm Mounting holes: 30.5x30.5mm Throttle Calibration: Supported ESC Programming: BLHeliSuite32 Includes 1x Hobbywing XRotor F722 3-6S 30x30 Stack/Combo (F7 FC / 32Bit 65A 4in1 ESC) 1x Hardware Set 1x AMASS XT60 Connector 1x Cable Set

Read more less

The Kakute F4 V2.4 is ready for DJI HD. Easily plug in and power your HD video transmitter (like DJI O3 Air Unit & Caddx Vista) with its on-board 9V/A regulator, plus 5 dedicated UARTs w/inversion for peripherals. This stack comes with a barometer, plus LED/buzzer pad & I2C for external GPS/Magnetometers. The Tekko32 is the first 4in1 ESC, featuring the powerful F4 MCU @150Mhz, giving you smooth control & fast response, 4~6S & BLHeli32 for 30x30 stack/combo.  Check out all our 30x30 Stacks and the rest of our HolyBro selection! Features New and faster F4 MCU @ 150Mhz (compared to F3 @108Mhz & F0 @48Mhz) PWM Frequency: 16k to 96k Separate drive & control circuit, this broadens the current capability of the drive circuit while reducing the electrical interference to the control circuit.  Specifications Holybro Kakute F4 HD V2.4 2-8S 30x30 Flight Controller MCU: STM32F405 IMU:  MPU6000 Barometer: BMP280 OSD: AT7456E 5x UARTs (1,3,4,4,6,7) 128 Mbit Dataflash chip Battery input voltage: 2-8S BEC 9V/3A - Optimized for DJI O3 Air unit BEC 5V/2A 7x PWM Outputs (6 Motor Output, 1 LED) Supports serial receivers (SBUS, iBus, Spektrum, Crossfire, ESLR). Mounting: 30 x 30mm, Φ4mm hole with M3 Grommets Dimension: 37x37mm Weight: 7g JST-SH1.0_8pin port (For 4in1 ESCs) JST-SH1.0_6pin port (For DJI/Caddx HD System and other VTX) Tekko32 F4 4in1 50A ESC Continuous Current: 50A x4 Burst Current: 60A x4 Supports 4-6S battery Supports DShot 150/300/600/1200 & MultiShot/OneShot/Proshot/PWM etc. ESC telemetry Supported Onboard analog current sensor No output BEC BLHeli_32 firmware 1000uf 35v capacitor included (highly recommended for 6s setup) Amperage meter scale ratio: 120 (V1.9 Version) Dimensions: 48x37x6mm / Weight: 13.8g Mounting holes: M4 30.5x30.5mm (M3 grommets included) Includes 1x Holybro Kakute F4 HD V2.4 4-6S 30x30 Stack/Combo (F405 FC/ 50A F4 32bit 4in1 ESC) 1x Wiring Kit Wiring Diagram

Read more less

The Holybro Kakute H7 has integrated Bluetooth, dual 4in1 ESC ports, HD camera plug, barometer, OSD, 6 UARTs, MicroSD card, 5V & 9V BEC, easy soldering layout, etc. Supporting DJI HD, its 9V regulator powers FPV Air Unit & Caddx Vista. With 6 UART ports & inversion, it offers unlimited Blackbox data logging. BetaFlight OSD displays info on FPV display, and barometer helps autonomous flight. LED & buzzer pad, I2C pad for external GPS/Magnetometer. Check out all our 30x30 Stacks and the rest of our HolyBro selection! Features This V1.3 now has USB-C, 9V 3A BEC for VTX, and JST-SH connector for VTX port. Specifications for HolyBro Kakute H7 V1.3 FC MCU - STM32H743 32-bit processor running at 480 MHz IMU - MPU6000 Barometer - BMP280 OSD - AT7456E Onboard Bluetooth chip - ESP32-C3 SpeedyBee IOS & Android App Compatible  Note: The Bluetooth onboard is set to automatically turn off when the flight controller is unlocked (arm) and turn on automatically when the flight controller is locked (disarm). 6x UARTs (1,2,3,4,6,7; UART2 is used for Bluetooth telemetry) 9x PWM Outputs (8 Motor Output, 1 LED) 2x JST-SH1.0 8pin ESC port (4in1 ESCs, x8/Octocopter compatible) 1x JST-SH1.0 6pin VTX port (For HD System like Caddx Vista & Air Unit) Battery input voltage: 7V to 42V BEC 5V 2A Cont. BEC 9V 3A Cont  USB Type-C Mounting - 30.5 x 30.5mm/Φ4mm hole with Φ3mm Grommets Dimension - 35x35mm Weight - 8g Specifications for Tekko32 F4 4in1 50A ESC Continuous Current: 50A x4 Burst Current: 60A x4 Supports 4-6S battery Supports DShot 150/300/600/1200 & MultiShot/OneShot/Proshot/PWM etc. ESC telemetry Supported Onboard analog current sensor No output BEC BLHeli_32 firmware 1000uf 35v capacitor included (highly recommended for 6s setup) Amperage meter scale ratio: 120 (V1.9 Version) Dimensions: 48x37x6mm / Weight: 13.8g Mounting holes: M4 30.5x30.5mm (M3 grommets included) Firmware Targets BetaFlight: KakuteH7 (v4.2.11 and above) INAV: KakuteH7 (4.0.0 & above) SD card support added in 4.1.0. ArduPilot: KakuteH7 (4.2.0 & above) Includes Holybro Kakute H7 V1.3 Tekko32 F4 50A 4-6S 30x30 Stack/Combo (H7 FC / 50A F4 32bit 4in1 ESC) 1x Wiring Kit Wiring Diagram

Read more less

Please note, this Flight Controller is based on the ATF435 chip opposed the the F4's and F7's most of the community is used to.  Downloading new drivers and using custom targets may be required. As long as your BetaFlight 10.10 you should be good to go! The iFlight Blitz ATF435 Stack/Combo provides dependable performance and efficient control of your 2-6S powered quadcopter. This 30x30 stack/combo features an ATF435 FC and 55A 8Bit 4in1 ESC to give you responsive controls and reliable power delivery. Fly worry-free and explore new heights. This flight controller comes with plug-in ports for 9V VTXs, LED/Buzzer, receiver, camera, & the ESC. The NEW ATF processors allow for a product like this, a 60-dollar stack that is feature-rich and comes with a 55Amp ESC, which is perfect for those amp-hungry builds.  Check out our other 30x30 Stacks & Combos as well as our entire iFlight selection! To configure download ATBetaflight and if that does not automatically connect, here are virtual com port drivers.  Future versions of Betaflight will fully support these boards. Specifications iFlight Blitz ATF435 MCU: AT32F435CGU7 Gyro: BMI270 Barometer: DPS310 OSD Chip: AT7456E Flash: 32MB (Blackbox flash) UARTS: 6 Motor outputs: 4x (SH1.0 connector) I2C serial: SDA / SLA pads Smartaudio / IRC Tramp VTX protocol supported LED controller: Yes Beeper pad: Yes Firmware target: IFLIGHT_BLITZ_ATF435 Mount pattern: 30.5x30.5mm / 4mm PCB hole diameter Dimensions: 36.5x35 mm Weight: 7.8g BEC: 5V 2.5A / 9V 2A Blitz E55S ESC Mounting Holes: 30.5x30.5mm/Φ4mm Weight: 14.7g Supports 2-6S lipo input MCU: G071 Constant: 55 Amps Burst: 65 Amp Current sensor: Yes BEC: No Current rate: 200 Supports: DShot DShot150/300/600/MultiShot/ OneShot etc. Target: Q-H-25 16.7(BlheliS) / Bluejay Q-H-50 (Bluejay) Include 1x iFlight Blitz ATF435 E55S 2-6S 30x30 Stack/Combo (ATF435 FC/ 55A 8Bit 4in1 ESC)

Read more less

The SkyStarsRC F7HD PRO4 stack/combo is the perfect choice for those looking for a reliable and powerful flight control system. Featuring an F722 FC and a KM60 AM-32 32Bit 60A 4in1 ESC, this stack is capable of handling 3-6S and can be counted on to provide smooth flying in any situation. Its MPU6000 ensures stable and accurate performance. This SkyStarsRC F7HD PRO4 F7 3-6S 30x30 Stack/Combo boasts huge soldering pads, proper spacing to avoid solder bridges, ESC connector on top for convenient repairs, TVS diode for reverse-polarity protection, 3A BEC power, pads arranged to minimize wire overlap, and gyroscope independent power supply. With no power lines near MPU6000 Gyro to avoid any EMI interference.  Every single unit is pre-tested with quality control. This stack supports a DJI O3 connector and a VTX ON/OFF Pit Switch. INAV and I2C are supported with this stack as well.  Check out our other 30x30 Stacks, and our SkystarsRC collection! Features Excellent over-current capability: By adopting the best PCB material and PCB production process. With the application of high TG materials, 3oz copper PCB & 2µm gold deposition process on PCB. Together with the 6-layer layout design of board, compared with other common 4 layers, It can withstand a bigger current. Extreme stably support 6S LiPo battery: By use of 24 pcs of new Toshiba standard 40V 5x6 Mosfet & imported from USA or Japan electronic materials. Plus advanced lead-free SMT Processing technology. Making the ESC fully able to support a 6S battery and get a better performance. Excellent heat dissipation performance: The CNC hollow aluminum alloy shell used is great for heat dissipation. Better control performance: Flashed with the latest AM_32 firmware in factory, support telemetry functions (including voltage, RPMS & current ) Specifications SKYSTARS F7HD Pro4 Flight controller: MCU: STM32F722RET6 216MHz Gyroscope: MPU6000 Baro: Bmp280 OSD: Betaflight SPI OSD DJI HD OSD(UART6) Black box: 16MB 6x Uarts: UART 1/2/3/4/5/6 4x PWM outputs 1x I2C 3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator(Red) USB Type-C(USB2.0) 1x JST-SH1.0_8pin connector (Gnd/Vbat/S1/S2/S3/S4/Rx3/Curr) 1x JST-SH1.0_6pin connector (10V/Gnd/TX6/RX6/Gnd/Sbus) VTX 10V/Vbat filtered power ON/OFF Pit switch Any spare UART supports DJI FPV OSD LED: 4 LED independent pads, support WS2812 programming lamp output. Receiver: Support Sbus, crsf, ibus, SBUS, XBUS, support 3.3v Spektrum satellite receiver, The default receiver input is UART1(You can solder ELRS RX on UART1), F7 has a built-in inverter, which can actually be installed in any spare UART. Input voltage: 3-6S BEC: 5V/10V 3A max dual-channel BEC supports stable power supply on the sky side of DJI O3 LDO 3.3V: Max.250mA BetaFlight firmware: SKYSTARSF722Pro INAV firmware: SKYSTARSF722HD Installation size: 30.5x30.5mm. The installation hole is M4 and supports shock column installation. External size 39x39mm Flight control weight: 6.9g Flight control onboard voltage sensor AM60 AM_32 60A 32Bit 3-6S 30.5mm 4in1 ESC: Input voltage: 3-6S LiPo Con.Current: 60A Peak Current: 70A≥ 10S Firmware: AM_32 Support: Dshot 600/1200 Mounting hole: 30.5X30.5 mm/M3 BEC: No Product size: 41x46x7.6mm Weight: 18g Includes 1x SkyStarsRC F722 HD PRO4 3-6S 30x30 Stack/Combo (F722 FC / KM60 AM-32 32Bit 60A 4in1 ESC) - MPU6000 8x Silicon grommets M4 to M3 2x JST-SH1.0_8pin cable, 4cm 1x JST-GH-6P cable for DJI port, 10cm Wiring Diagram

Read more less

This SkyStarsRC Fly Stack is a powerful 3-6S 20x20 stack/combo with superior F722 FC, and powerful MVP60 F4 128K 32Bit 60A 4in1 ESC. This stack features an MPU6000 for smooth, efficient performance. Enjoy reliable control and smooth operation for a great flying experience! Check out all our 20x20 stacks, and our SkyStarsRC collection! Specifications SKYSTARS F722RS 20X20 Flight Controller MCU: STM32F722RGT6 216MHz IMU: MPU6000 (SPI) OSD: Betaflight OSD & DJI HD OSD (UART6) 6 hardware UARTS (UART1,2,3,4,5,6) Barometer: NO Buzzer Pad: YES BEC: 5V 3A Input Voltage: 3-6S Lipo Blackbox: 16MB Firmware: SKYSTARS F7RS Dimensions: 26x28x7mm Mounting Holes: Standard 20mm/M3 square to center of holes Weight: 4.9g SKYSTARS MVP60A F4 32Bit 3-6S 20×20 4in1 ESC Input voltage: 3-6S LiPo Con.Current: 60A Peak Current: 80A≥ 10S Firmware: BLHeli_32 Support: Dshot 600/1200 Mounting hole : 20X20 mm/M3 BEC: No Product size: 35.8x47x6.5mm Weight: 17g Includes 1x SkyStarsRC Fly Stack F722RS 3-6S 20x20 Stack/Combo (F722 FC / MVP60 F4 128K 32Bit 60A 4in1 ESC) - MPU6000

Read more less

The SkyStarsRC Fly Stack F405 HD2 stack is an excellent choice for power-hungry pilots. Its F405 flight controller and KO50 8-bit 50A 4-in-1 ESC provide reliable, consistent performance, while its 3- to 6-cell battery supports power delivery up to 50 amps. Its 30x30 stack is perfect for professional-level pilots who need reliable, efficient power. Check out our other 30x30 Stacks, and our SkyStarsRC collection! Specifications SkyStarsRC F4 Flight Controller MCU: STM32F405 IMU: BMI270 OSD: AT7456E Blackbox: 16MB 6X Uarts(1 2 3 4 5 6) WS2812 led Strip: YES Baro: YES Beeper: YES BEC: 5V/2A,3A Peak Betaflight FC Target: SKYSTARSF405 INAV FC Target:SKYSTARSF405HD Mounting: 30.5x30.5mm, 4mm with Grommets 3mm Dimensions: 36x36mm Weight: 6g K050 50A 4in1 ESC Dimension: 41x46mm Mounting Holes: 30.5x30.5mm/¦µ3mm Weight:13.3g Supports 3-6S Lipo input BB21 MCU, 48Mhz Runs BLHELI 16.X Firmware, Support Bulejay. Current sensor: YES BEC: NO Supports: DShot DShot150/300/600/MultiShot/ OneShot etc. Target: Q-H-50 BLS 16.7 Includes 1x SkyStarsRC Fly Stack F405 HD2 3-6S 30x30 Stack/Combo (F405 FC / KO50A 8Bit 50A 4in1 ESC) 4x Damping Rubbers (M3x3.5mm) 1x XT60 connector and wires 2x 8pin wiring harness (1x 70mm,1x 50mm) 1x 35v 560uf Capacitor Wiring Diagram

Read more less

The SkyStars Fly Stack features an F722 HD Pro 3 flight controller and a KO45 45A BLHeli_32 4-in-1 128K ESC with a 30x30 mounting pattern! Features The ESC has an onboard filter capacitor that suppresses the back electromotive force, stabilizes the battery voltage, and protects the flight control ESC precision components. Built-in inverter, which can actually be installed in any spare UART. EMI Shell provides a stronger anti-interference capability. DJI FPV OSD is supported by any spare UART VTX 10V/Vbat filtered power ON/OFF switch Flight control onboard voltage sensor F722 HD Pro 3 Flight Controller 30x30 Mounting Pattern KO45 45A 128K ESC 3-6S LiPo Support Specifications F722 HD PRO 3 OSD FC   Receiver: Support Sbus, CRSF, IBUS, SBUS, XBUS, support 3.3v Spektrum satellite receiver, The default receiver input is UART1(You can solder ELRS RX on UART1), F7 has a Installation size: 30.5x30.5mm (The installation hole is M4 and supports shock column installation) BEC: 5V/10V 3A max dual-channel BEC supports stable power supply on the sky side of DJI LED: 4 LED independent pads, support WS2812 programming lamp output. 1x JST-SH1.0_8pin connector (Gnd/Vbat/S1/S2/S3/S4/Rx3/Curr) LEDs for FC STATUS (Blue, Green) and 3.3V indicator(Red) :3 1x JST-SH1.0_6pin connector (R1/G/R6/T6/G/10V) OSD: Betaflight SPI OSD DJI HD OSD(UART6) BetaFlight firmware: SKYSTARSF722Pro INAV firmware: SKYSTARSF722HD MCU: STM32F722RGT6 216MHz External size: 39x39mm 6x Uarts: UART 1/2/3/4/5/6 USB Type: Type-C (USB2.0) Flight control weight: 6.9g LDO 3.3V: Max.250mA Barometer :Bmp280 Input voltage: 3-6S Gyroscope: BMI270 Black box: 16MB PWM outputs: 4 I2C: 1 KO45 45A 4in1 ESC Support: 128K Dshot1200, Dshot600, Dshot300, Dshot150, Oneshot125, Multishot, PWM control signal Continuous working current: 45A 60A Power supply voltage: 3-6S (12-26V) Moutning Pattern: 30.5x30.5MM Firmware: BLHELI 32 ESC 5V BEC output: NO Aperture: 4MM Weight: 14.6g Includes 1x SkyStarsRC Fly Stack F7 HD Pro 3 3-6S 30x30 Stack/Combo (F722 FC / KO45 32Bit 45A 4in1 ESC) 1x JST-GH-6P cable for DJI port, 10cm 2x JST-SH1.0_8pin cable, 4cm 8x Silicon grommets M4 to M3

Read more less

The SkyStars Fly Stack features an F722 HD Pro 3 flight controller and a KM60 60A BLHeli_32 4-in-1 128K ESC with a 30x30 mounting pattern! Check out our other 30x30 Stacks, and our SkyStarsRC collection! Features The ESC has an onboard filter capacitor that suppresses the back electromotive force, stabilizes the battery voltage, and protects the flight control ESC precision components. Built-in inverter, which can actually be installed in any spare UART. EMI Shell provides a stronger anti-interference capability. DJI FPV OSD is supported by any spare UART VTX 10V/Vbat filtered power ON/OFF switch Flight control onboard voltage sensor F722 HD Pro 3 Flight Controller 30x30 Mounting Pattern KM60 60A 128K ESC 3-6S LiPo Support Specifications SkyStarsRC F7HD Pro3 FC MCU: STM32F722RGT6 216MHz Gyroscope: BMI270 Baro: Bmp280 OSD: Betaflight SPI OSD DJI HD OSD(UART6) Black box: 16MB 6x Uarts: UART 1/2/3/4/5/6 4x PWM outputs 1x I2C 3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator(Red) USB Type-C(USB2.0) 1x JST-SH1.0_8pin connector (Gnd/Vbat/S1/S2/S3/S4/Rx3/Curr) 1x JST-SH1.0_6pin connector (R1/G/R6/T6/G/10V) VTX 10V/Vbat filtered power ON/OFF switch DJI FPV OSD is supported by any spare UART LED: 4 LED independent pads, support WS2812 programming lamp output. Receiver: Support Sbus, CRSF, IBUS, SBUS, XBUS, support 3.3v Spektrum satellite receiver, The default receiver input is UART1(You can solder ELRS RX on UART1), F7 has a built-in inverter, which can actually be installed in any spare UART. KM60 60A 4in1 ESC Input voltage: 3-6S LiPo Con. Current: 60A Peak Current: 70A≥ 10S Firmware: BLHeli_32 Support: Dshot 600/1200 Mounting pattern: 30.5mm/M3 BEC: No Product size: 41x46x7.6mm Weight: 17g about Includes 1x SkyStarsRC Fly Stack F7 HD Pro3 3-6S 30x30 Stack/Combo (F722 FC / KM60 32Bit 60A 4in1 ESC) 4x Damping Rubbers (M3x3.5mm) 1x XT60 connector and wires 2x 8pin wiring harness (1x 70mm,1x 50mm) 1x 35v 560uf Capacitor

Read more less

The SkyStarsRC Fly Stack F7 HD Pro4 3-6S 30x30 Stack/Combo is a powerful and reliable 3-6S drive system for your drone needs. With an F722 FC and a KM65 F4 128K 32Bit 65A 4in1 ESC, you can fly with absolute precision and control thanks to the MPU6000. Enjoy a smooth and safe flight experience every time! SkyStarsRC KM65 F4 128K 32Bit 65A 3-6S 30x30 4in1 ESC has great performance with a maximum current of 65A and a peak current of 90A. This ESC is powerful and reliable, and ideal for use in any 3-6S 30x30 setup. Get ready for a smooth and efficient flying experience! This board has support for a PWM frequency of 128K and comes with an F4 processor for incredibly smooth usage. This ESC also features a heatsink designed to distribute heat evenly. If there's an ESC you're going to go with for racing, then this is it! Check out our other 30x30 Stacks, and our SkyStarsRC collection! Specifications Skystars F722 HD Pro4 Power supply: 3-6S Processor: STM32F722RGT6 IMU: MPU6000 Blackbox: 16MB BEC: 5V@3A, 10V@3A Connector for DJI FPV Integrated barometer Mounting holes: 30.5x30.5mm M3 (with soft mount) SkyStarsRC KM65 F4 128K 32Bit 65A 3-6S 30x30 4in1 ESC Input voltage: 3-6S LiPo Con. Current: 65A Peak Current: 90A≥ 10S Firmware: BLHeli_32 Support: Dshot 600/1200 Mounting hole: 30.5mm/M3 BEC: No Product size: 45.6x45x7.6mm Weight: 19g Includes 1x SkyStarsRC Fly Stack F7 HD Pro4 3-6S 30x30 Stack/Combo (F722 FC / KM65 F4 128K 32Bit 65A 4in1 ESC) - MPU6000

Read more less

The SpeedyBee F4 3-6S 20x20 Stack/Combo (F405 FC / 35A 8bit 4in1 ESC)! Experience feature-rich performance and an unbeatable price for a 20x20 stack. Utilizing an upgraded F405 flight controller chip with better performance than the F411, it features a built-in Bluetooth chip for seamless wireless Betaflight tuning. The board comes with a 4-level battery voltage display, built-in barometer, and supports connectivity to all DJI Air Units. It offers 4 available UART ports, and a dual BEC setup with 5V 2A and 9V 3A outputs. This ESC provides four synchronized outputs with a continuous current of 35A, delivering strong power to drive all 2-4 inch and lightweight 5-inch quadcopters via 4-6S battery. Equipped with a TVS transient suppression diode onboard, it better absorbs surge voltage, providing enhanced protection for the ESC. Check out all our 20x20 stacks, and our SpeedyBee products!   Features User Manual DJI compatible  Feature-rich Budget-friendly price point Compatible with M2 and M3 Specifications Product Name: SpeedyBee F405 Mini BLS 35A 20x20 Stack Flight Controller: SpeedyBee F405 Min ESC: SpeedyBee BLS 35A Mini V2 4-in-1 ESC Bluetooth: Supported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Please make sure the MSP switch on UART 4 is turned on and set to a baud rate of 115200, otherwise Bluetooth functionality will not be available. WiFi: NOT Supported Wireless FC Firmware Flashing: NOT Supported Wireless: Blackbox Download & Analysis NOT Supported Power Input: 3-6S LiPo Mounting: 20 x 20mm 3.5mm hole size， Compatible with M2 and M3 screws/Silicone grommets Dimension: 32mm(L) x 35mm(W) x 14.2mm(H) Weight: 13.5g SpeedyBee F405 V3 30x30 Flight Controller MCU: STM32F405 IMU(Gyro): ICM42688PUSB Port Type: Type-C Barometer: Built-in OSD Chip: AT7456E chip BLE Bluetooth: Supported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Please make sure the MSP switch on UART 4 is turned on and set to a baud rate of 115200, otherwise Bluetooth functionality will not be available. Wireless FC Firmware Flashing: NOT Supported. Please connect to the Betaflight configurator on the PC to do FC firmeare update Wireless Blackbox Download & Analysis: NOT Supported. Please connect to the Betaflight configurator on the PC to do blackbox analysis. WIFI: Not supported DJI Air Unit Connection Way: Direct soldering DJI Air Unit Compatibility: Compatible with all DJI Air Units: DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1. Please use the solder pads < 9V, G, T1, R1, G, SUBS(R2) > on the front right corner of the flight controller to make a pin-to-pin connection with the solder pads on the DJI Air Unit. UART1(T1, R1) is used for OSD and SUBS(R2) is used for DJI Air Unit’s internal SBUS receiver signal input. Blackbox: 8MB Onboard Flash BetaFlight Camera Control Pad: Yes(CC pad on the front side) Current Sensor Input: Supported. For SpeedyBee BLS 35A V2 ESC, please set Scale=250 and Offset=-500. Power Input: 3-6S LiPo. The flight controller is powered through the G, V wires of the 8pin harness or G, V pads from the bottom side of the flight controller. 5V Output: 4 groups of 5V output, three +5V pads and 1 BZ+ pad( used for Buzzer) on front side. The total current load is 2A. 9V Output: 1 group of 9V output, one +9V pad on front side. The total current load is 3A. 3.3V Output: Supported. Soldering pad named ‘3V3’ on the front top of the flight controller. Designed for 3.3V input receivers. Up to 500mA current load. 4.5V Output: Supported. Designed for radio receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load. ESC Signal: M1 - M4 wires or soldering pads on bottom side. UART: 6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6 ESC Telemetry: UART R5(UART5) I2C: Supported. DA & CL pads on front side. Used for magnetometer, sonar, etc Traditional Betaflight LED Pad: Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LEDs controlled by the Betaflight firmware. Buzzer: BZ+ and BZ- pad used for 5V Buzzer BOOT Button: Supported. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked. RSSI Input: Not Supported Smart Port / F.Port: Not Supported Supported Flight Controller Firmware BetaFlight(Default), INAV Firmware Target Name: SPEEDYBEEF405MINI Mounting: 20 x 20mm 3.5mm hole diameter, Compatible with M2 and M3 screws/Silicone grommets. Dimension: 30(L) x 32(W) x 7.8(H)mm Weight 9.6g SpeedyBee 35A BLHeli_S Mini V2 4-in-1 ESC Firmware: BLHeli_S J-H-40 Continuous Current: 35A x 4 Burst Current: 45A(5seconds) ESC Protocol: DSHOT300/600 Power Input: 3-6S LiPo Power Output: VBAT(Battery voltage, used to power the flight controller) Current Sensor: Support (Scale=250 Offset=-500) Mounting: 20 x 20mm ∅3.5mm hole size, compatible with M2 and M3 screws/Silicone grommets. Dimension: 35 x 35 x 5.5mm Weight: 7.2g Includes 1x SpeedyBee F4 3-6S 20x20 Stack/Combo (F405 FC / 35A 8bit 4in1 ESC) Wiring Diagram

Read more less

The Speedy Bee F405 50A Stack V3 includes all the features a user would expect from a modern flight controller and ESC stack, but at an incredible price.  The F405 V3 flight controller features the STM32F405 MCU, an onboard 4-level battery life indicator, a Micro-SD card slot for Blackbox logging, 4 groups of LED strip pads, a DJI plug for digital quads, and built-in Bluetooth for wireless configuration through the SpeedyBee App.  The 50A 4-In-1 ESC features a built-in TVS protective diode, and Japanese made TDK SMT capacitors, and even comes with a low ESR 1500uF capacitor. Check out all our 30x30 stacks & combos, and all our Speedy Bee products! Specifications Speedy Bee F405 V3 Flight Controller MCU: STM32F405 IMU(Gyro): BMI270 USB Port: Type-C Barometer: Built-=In OSD Chip: AT7456E chip BLE Bluetooth: Supported DJI Air Unit Connection: 6-pin connector and solder pads Blackbox Micro-SD Card: 32GB max Current Sensor: Supported Power Input: 3S-6S LiPo Power Output: 9V (2A), 3.3V (500mA), 4.5V(1A), 5V(2A) ESC Signal: M1-M8 available UART: 5 Sets I2C: Supported LED: Supported Buzzer: Supported Boot Button: Press for DFU mode, press when powered to change LED modes Firmware Target: SPEEDYBEEF405V3 Mounting: 30.5 x 30.5mm ( 4mm hole diameter ) Dimensions: 41.6(L) x 39.4(W) x 7.8(H)mm Weight: 9.6g 32Bit 50A 3-6S 4in1 ESC Firmware: BLHeli_S JH50 Wireless Configuration: Full Configuration Supported in Speed Bee App PC Configurator: https://esc-configurator.com/ Continuous Current: 50A * 4 Burst Current: 55A * 4 TVS Protective Diode: YES External Capacitor: 1500uF Low ESR Capacitor Included ESC Protocol: DShot 300/600 Power Input: 3-6S LiPo Power Output: VBAT Current Sensor: Scale=386 Offset=0 Mounting: 30.5 x 30.5mm ( 4mm hole diameter ) Dimensions: 45.6(L) * 44(W) * 6.1mm(H) Weight: 13.8g

Read more less

Richer features, unbelievable price! The SpeedyBee F405 V4 BLS 3-6S 30x30 Stack/Combo is a powerhouse of features at a remarkably competitive price. It boasts a wireless FC & ESC configuration, dual gyroscope power supply filtering, onboard 4-level battery indicators, 8 motor support, 4x LED strips soldering pads, 3A output 5V & 9V BECs, fixed SD card compatibility issue, wireless motor direction change, a DJI Air Unit plug-and-play, and a built-in barometer. Get it now and enjoy an unparalleled performance! The powerful 55A (70A burst) 4-in-1 ESC, built with aluminum alloy heat sink + TVS protective diode + Japan made TDK SMT capacitors + external 1000uF low ESR capacitor, everything is for a durable build and smooth flight. All of that for only $69.99! Top-shelf spec at a crazy low price, what are you waiting for? Interested in the SpeedyBee BLS 8Bit 55A 3-6S 30x30 4in1 ESC? Interested in the SpeedyBee F405 V4 3-6S 30x30 Flight Controller? Check out all our 30x30 stacks & combos, and all our Speedy Bee products! Features User manual Wireless FC & ESC full configuration ESC upgraded to 55A with heat sink  Dual gyroscope power supply filtering  Onboard 4-level battery indicators Supports up to 8 Motors  4x LED strips soldering pads 5V & 9V BECs upgraded to 3A output Fixed SD card compatibility issue Change motor direction wirelessly  1000uF huge filtering capacitor  DJI Air Unit plug-and-play Built-in barometer Specifications SpeedyBee F405 V4 30x30 Flight Controller MCU: STM32F405 IMU(Gyro): ICM42688P USB Port Type: Type-C Barometer: Built-in OSD Chip: AT7456E chip BLE Bluetooth: Supported. Used for Flight Controller configuration (MSP should be enabled with Baud rate 115200 on UART4) WIFI: Not supported DJI Air Unit Connection Way: Two ways supported: 6-pin connector or direct soldering. 6-pin DJI Air Unit Plug: Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.Blackbox MicroSD Card Slot: Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High capacity (SDHC) under 32GB, so extended capacity cards (SDXC) are not supported(Many high-speed U3 cards are SDXC). Also the microSD card MUST be formatted with the FAT16 or FAT32 (recommended) format, you could use any SD card less than 32GB, but the Betaflight can only recognize 4GB maximum. Current Sensor Input: Supported. For SpeedyBee BLS 55A ESC, please set scale = 400 and Offset = 0. Power Input: 3S - 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side) 5V Output: 9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 3A. 9V Output: 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 3A. 3.3V Output: Supported. Designed for 3.3V-input receivers. Up to 500mA current load. 4.5V Output: Supported. Designed for a receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load. ESC Signal: M1 - M4 on bottom side and M5-M8 on front side. UART: 6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6 ESC Telemetry: UART R5(UART5) I2C: Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc. Traditional Betaflight LED Pad: Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware. Buzzer: BZ+ and BZ- pad used for 5V Buzzer BOOT Button: Supported.[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.[B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware. RSSI Input: Supported. Named as RS on the front side. Smart Port / F.Port: Not supported Supported Flight Controller Firmware: BetaFlight(Default), INAV Firmware Target Name: SPEEDYBEEF405V4 Mounting: 30.5 x 30.5mm( 4mm hole diameter) Dimension: 41.6(L) x 39.4(W) x 7.8(H)mm Weight: 10.5g SpeedyBee BLS 55A 30x30 4-in-1 ESC Firmware: BLHeli_S J-H-40 Wireless Configuration: Full Configuration Supported in the SpeedyBee app PC Configurator Download Link: https://esc-configurator.com/ Continuous Current: 55A x 4 Burst Current: 70(10 seconds) TVS Protective diode: Yes External Capacitor: 1000uF Low ESR Capacitor(In the package) ESC Protocol: DSHOT300/600 Power Input: 3-6S LiPo Power Output: VBAT Current Sensor: Support (Scale=400 Offset=0) ESC Telemetry: Not supported Mounting: 30.5 x 30.5mm( 4mm hole diameter) Dimension: 45.6(L) x 44(W) x 8mm(H) Weight: 23.5g Includes 1x SpeedyBee F405 V4  BLS 3-6S 30x30 Stack/Combo (F405 FC / 8Bit 55A 4in1 ESC)  Wiring Diagram

Read more less

The ultimate 20x20 stack for on the go tuning! With integrated bluetooth, this stack allows you to access Betaflight and even BLHeli through the Speedy Bee app. Check our other Stacks and our SpeedyBee products!  Specifications SpeedyBee F7 Mini Input Voltage: 3-6S MCU: STM32F722 Gyro: BMI270 Barometer: No OSD Chip: AT7456E Bluetooth: Yes DJI Air Unit Soldering Pads: Supported BlackBox: 8MB Flash Current Sensor: Yes BEC: Yes ESC Signal Pads: 4 UARTs: 3(UART1, UART2, UART3) ESC Telemetry: R4(UART4) LED Pad: Used for WS2812 LED Buzzer: Yes Firmware: BetaFlight(Default), EMUFlight, INAV Firmware Target: SPEEDYBEEF7MINI Mounting Dimensions: 20 x 20mm, 3.5mm hole diameter Weight 5.7g SpeedyBee 35A BLHeli_S ESC Power Input: 3-6S Firmware: BLHeli_S JH40 Max Continuous Current: 35A Max Burst Current: 45A ESC Protocol: DSHOT300/600 Current Sensor: Yes Mounting Dimensions: 20 x 20mm, 3.6mm hole diameter Weight: 7g Includes 1x SpeedyBee F7 Mini 35A 3-6S 20x20 Stack/Combo

Read more less

The SpeedyBee V3 F722 3-6S 30x30 Stack/Combo (F722 FC / 50A 32bit 4in1 ESC) is a marvel to behold. The latest iteration of the SpeedyBee Stack, the V3 is packed with powerful new upgrades. Faster Wi-Fi upgrades, black box retrieval within a minute, supports up to 8 motors, and features soldering pads on one end, and pin connectors on the other in case soldering isn't your thing. The 50A 4in1 ESC is fitted with a high-quality CNC heat sink shield to significantly reduce the heat from your MOSFETs ensuring stable current flow at a high-throttle position. This ESC should have no issues with overheating. A great benefit in a stylish blue finish. Check out our other 30x30 Stacks and all our Speedy Bee products! Specifications F722 2-6S Flight Controller MCU: STM32F722 IMU: BMI270 USB: Type-C Baro: BMP280 (I2C) OSD: BetaFlight OSD w/ AT7456E chip BLE Support, used for Flight Controller configuration WiFi Support, used for data transfer, e.g firmware flashing, and Blackbox analysis. DJI Air Unit plug: A full DJI Air Unit JST slot onboard BlackBox: 500MB onboard data flash BetaFlight Camera Control Pad: Yes Power input: 3S - 6S Lipo 10 groups of 5V output, three +5V pads and 1 BZ+ pad (used for Buzzer) on front side, and 6 +5V output included in the connectors on bottom side. The total current load is 2A. 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 4A. Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load. Supported. Designed for 3.3V-input receivers. Up to 500mA current load. ESC signal M1 - M4 on bottom side and M5-M8 on front side. UART: 5 sets (UART1, UART2, UART3, UART4, UART6) ESC Telemetry: UART UART4 RX I2C: Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc. LED: Used for WS2812 LED controlled by Betaflight firmware. Buzzer: BZ+ and BZ- pad used for 5V Buzzer Boot button: Yes RSSI input: Yes SmartPort: Supported Support Flight Controller Firmware: BetaFlight(Default), EMUFlight, INAV Target: SPEEDYBEEF7V3 Mounting: 30.5x30.5mm, 4mm hole size Dimension 41(L) x 38(W) x 8.1(H)mm Weight 9g 32Bit 50A 3-6S 4in1 ESC Firmware: SpeedyBee BL32 50A Continuous Current: 50Ax4 Burst Current: 55A(5S) Power input: 3S - 6S LiPo Power output: VBAT Current Sensor: Supported (Scale=490 Offset=0) Mounting: 30.5x0.5mm, 4mm hole size Dimension: 45.6(L)x40(W)x8.8mm(H) Weight: 19.2g with heat sink Includes 1x SpeedyBee BL32 32bit 50A 3-6S 30x30 4in1 ESC Wiring Diagram

Read more less

Unleash the true potential of your drone with the TMOTOR Velox CINE F7 Stack – the powerhouse combo of Velox CINE F7 FC and the robust V50A SE 4-in-1 ESC. Designed for those who understand that “average” just doesn’t cut it in the high-octane world of drone flight. Performance That Leaves ‘Good Enough’ in the Dust: Dive into the specs, and you’ll see the ESC isn’t just smart, it’s ‘I-just-skipped-a-grade’ smart. With an F4 MCU flexing 50% more brainpower than its predecessor, it’s not just keeping up; it’s setting the pace. The flight controller is not one to be outdone. Equipped with an F7 MCU, it’s the tech equivalent of going from a brisk walk to a supersonic jet, boasting 30% more computing power than the F4. Stability Meets Responsiveness: Our gyroscopes don’t mess around. High sampling rates? Check. A concoction of specialized optimization programs, whisper-quiet circuitry, and low noise design? Check, check, and check. Expect a flight experience so smooth, you’ll be forgiving of the occasional turbulence in life. Upgrade your firmware to version 4.4.2 or better, and unlock the secret level of flight control. Think of it as the cheat code for unrivaled stability. Endurance: Tested, Proven, Assured: 1,000 real flights with the Velox V3 motors and no glitches to report. That’s not just quality; that’s ‘make-a-notebook-out-of-it’ level consistency. Check out our other 30x30 Stacks & Combos and all our T-Motor products!   Specifications VELOX CINE F7 Flight Controller MCU: STM32F722 Input Voltage: 3-6S Gyroscope: ICM-42688P OSD: AT7456E&HD Barometer: SPL06 Mounting Holes: 30.5x30.5/Φ4mm Size: 36x36x8mm Weight: 9.2g Firmware: TMTR-TMOTORVELOXF7V2 (BETAFLIGHT) V50A SE ESC MCU: AT32F421 Input Voltage: 3-6S Current: 50A Peak Current(5S): 60A Size: 41x44.4x5.8mm Mounting Holes: 30.5x30.5/Φ4mm Weight: 12.3g Includes 1x T-Motor CINE F7 FC+ V50A SE 3-6S 30x30 Stack/Combo (F722 FC / F4 32Bit 50A 4in1 ESC)

Read more less

T-Motor's powerful F7 Flight Controller combined with the T-Motor F55A Pro II ESC will give you optimized performance and seamless integration in your electronics stack. The F55 Pro II updates the original F55 with a new heatsink design, LEDs, and increased the BEC current to 10V@2A. Fully capable of pushing 6s with 75A burst and a sustained 55A current draw. Equipped with the latest in ESC technology such as 32-bit capability and BLHeli32 firmware. Browse our 30x30 Flight Controllers and all our T-Motor products! Specification F7 FC MCU: STMF722RET6 Gyro: BMI270 Memory: 16M Input Voltage: 12v-25-2v (3-6S) BEC: 5V/2A Dimensions: 37mm x 37mm Mounting Holes: 30.5mm x 30.5mm Weight: 7.4g Firmware Target: TMOTORF7 (Betaflight) F55A Pro II 55A 3-6s BLHeli32 4-in-1 ESC w/ BEC Continuous current: 4x55A BLHeli_32 32bit Burst current: 4x75A BEC Output: 10V @2.0A Size: 45x41x7.3mm Weight: 17.5g (Including Heatsink) Support DSHOT150/300/600/1200 Includes 1x T-Motor F7 Flight Controller 1x T-Motor F55A Pro II 55A 3-6s BLHeli32 4-in-1 ESC w/ BEC 1x XT-60 Pigtail 1x Insulation Board 4x Link Board 4x M3x30 Screw 2x FC to ESC Cable 4x Non-Slip Nut 1x Spacers 1x Capacitor

Read more less

The T-Motor F7 & F55A Stack now comes in a version meant specifically for the DJI Digital FPV System! Including a plug for your Air Unit and a 10V 2A BEC to power it.  Check out all our 30x30 Flight Controllers, all our DJI compatible gear, and all our T-Motor products! Specifications FC Input Voltage: 3-6S Gyro: BMI270 Master chip: STM32F722RET6 Flash: 16MB BEC: 5V 2A, 10V 2A Mounting hole: 30.5x30.5mm Weight: 8.4g Size: 37x37mm Firmware: TMOTOR F7(Betaflight) ESC Continuous current: 4*55A BLHeli_32 32bit Burst current: 4*75A BEC Output: 10V @2.0A Size: 45x41x7.3mm Weight: 17.3g (Including Heatsink) Support DSHOT150/300/600/1200 Includes 1x T-Motor F7 HD 30x30 Flight Controller for DJI 1 x F55A Pro II 4 in 1 Brushless ESC Wiring Diagram

Read more less