RaceDayQuads
RaceDayQuads Aikon F7 Mini V3.1 HD 20x20 Flight Controller
This FC pairs seamlessly with any Aikon ESC. The F7 MCU will allow you to dial in your tune the way you want it and the DJI plug and play means it's ready to go with the Air Unit or Vista. Check out all our 20x20 FCs, our DJI compatible gear section, and all our Aikon gear! Features 216mhz F7 processor 5 Software invertable hardware UARTS Onboard OSD and blackbox Software controlled VTX power switch LED outputs Quick connection cable for 4-in-1 ESCs On-board high overhead voltage regulators up to 6S (50v peak for voltage spikes) 10V/1.5A regulator for DJI HD system DJI Quick Connect Port Specifications Input Voltage: 2-6s Mount Hole: 20x20mm Betaflight Target: AIKONF7 MCU: STM32F722RET6 IMU: BMI270 Blackbox SPI: 16MB Weight: 8g Includes 1x Aikon F7 Mini V3 HD 20x20 Flight Controller for DJI Wiring Diagram
$57.99
RaceDayQuads AxisFlying Argus F7 HD 3-6S 30x30 Flight Controller
The latest from AxisFlying, the Argus F7 is a powerhouse of a chip. It comes in two versions, regular and PRO which has a CNC heat dissipation aluminum cover. It has a high-performance F722 chip, onboard barometer, OSD and Black Box. And it can support up to 8 motors! This chip comes packed with power. Pair it with the Argus 65A ESC for ease of installation; a convenient plug-and-play feature. And it supports the new DJI O3 Air Unit! AxisFlying has got you covered! Check out all our 30x30 Flight Controllers, and all our Axis Flying Products! Features High-quality and large-size MOSFETs are selected, with low internal resistance and low heat generation. No welding, more peace of mind. With this FC, HD Air unit, analog camera, GPS, and other common peripherals all support direct plug-in Integrated dual BEC, support DJI O3 Air Unit direct connection The FC supports up to 8 motor outputs, easily build your X8 drone Quickly check the working status of the FC by turning on and off the corresponding status indicator light Specifications MCU: STM32F722RET6 Gyro: BMI270 Barometer: Yes OSD: Yes BEC: 9V/2A, 5V/2A UART Ports: 6 Black Box: 16MB onboard Number of supported motors: 8 Firmware Name: AXISFLYINGF7 Input Voltage: 3-6S LiPo (12-50V Max) Installation Holes: 30.5x30.5mm M3 Includes 1x AxisFlying Argus F7 3-6S 30x30 Flight Controller 1x Assorted Connector wires
$59.89
RaceDayQuads AxisFlying Argus F7 PRO HD 3-6S 30x30 Flight Controller
The latest from AxisFlying, the Argus F7 is a powerhouse of a chip. It comes in two versions, regular and PRO which has a CNC heat dissipation aluminum cover. It has a high-performance F722 chip, an onboard barometer, OSD and Black Box. And it can support up to 8 motors! This chip comes packed with power. Pair it with the Argus 65A ESC for ease of installation; a convenient plug-and-play feature. And it supports the new DJI O3 Air Unit! AxisFlying has got you covered! Check out all our 30x30 Flight Controllers, and all our Axis Flying Products! Features High-quality and large-size MOSFETs are selected, with low internal resistance and low heat generation. No welding, more peace of mind. With this FC, HD Air unit, analog camera, GPS, and other common peripherals all support direct plug-in Integrated dual BEC, support DJI O3 Air Unit direct connection The FC supports up to 8 motor outputs, easily build your X8 drone Quickly check the working status of the FC by turning on and off the corresponding status indicator light Specifications MCU: STM32F722RET6 Gyro: BMI270 Barometer: Yes OSD: Yes BEC: 9V/2A, 5V/2A UART Ports: 6 Black Box: 16MB onboard Number of supported motors: 8 Firmware Name: AXISFLYINGF7 Input Voltage: 3-6S LiPo (12-50V Max) Installation Holes: 30.5x30.5mm M3 Includes 1x AxisFlying Argus F7 3-6S 30x30 Flight Controller 1x Assorted Connector wires
$69.89
RaceDayQuads AxisFlying Argus Mini F7 4-6S 20x20 Flight Controller - MPU6000
The lightweight Argus Mini is specially designed for small size FPV drone, reducing the weight of the whole FPV to a greater extent while providing stable and excellent control. This flight controller is small and compact while boasting community favorite MPU6000 gyro for the best performance. Check out all our 20x20 FCs and all our Axis Flying Products! Specifications MCU: STM32F722RET6 FC target: AXIS FLYING F7 PRO Mounting Holes: 20x20mm M2/M3 FC: Axisflying F7 PRO Gyro: MPU6000 BEC: 5V 3A Blackbox: 16MB Weight: 5g UART: 1-5 OSD: Supported Barometer: Supported Size: 28.5x27x6.2mm Includes 1x AxisFlying Argus Mini F7 4-6S 20x20 Flight Controller - MPU6000
$64.89
RaceDayQuads DarwinFPV F411 3-6S 30x30 / 20x20 Flight Controller
DarwinFPV F411 3-6S FC is currently the cheapest in the FPV world and a direct replacement for the CineApe, designed to reduce the budget of entry-level FPV pilots as much as possible. At the same time, we have also filled the flight control with glue, which greatly reduces the risk of damage to components caused by frequent crashes by novices. Check out our other flight controllers and our Darwin FPV products! Specifications Input Voltage: 3-6S MCU: STM32F411 Gyro: MPU6500 OSD: Yes UARTs: 2 Sets ESC Connections: Yes Firmware: DARWINF411 BEC: 5V Current Sensor: Yes Barometer: BMP280 Black Box: SD Slot Stack Size: 30x30 / 20x20 Dimensions: 37x37mm Includes 1x DarwinFPV F411 3-6S 30x30 / 20x20 Flight Controller
$29.99
RaceDayQuads Diatone Mamba DJI F722 APP MK4 30x30 Flight Controller
The Diatone Mamba MK4 is an F722 flight controller. With WiFi capabilities through the SpeedyBee APP, this stack is the perfect addition to your FPV build. This version has an IMC42688P Gyro. Check out all our 30x30 FCs and all our Diatone Gear! Specifications MCU: STM32F722 GYRO: IMC42688P Barometer: Yes OSD: Yes Blackbox: 16M Flash Memory Uarts: 6Set ESC Telemetry: Yes Power Led: Yes LED Controller: BF LED/MB LED F.Port: Yes RSSI: Yes Buzz: Yes Input: 3-6S Lipo TVS Protection: Yes BEC: 3.3V/0.5A, & 5V/3A, and 9V/3A Mounting: 30.5x30.5mm, M3 Includes 1x Diatone Mamba DJI F722 APP MK4 30x30 Flight Controller 5x M3 ESC Isolation Dampers 5x M3 Silicone Dampers 1x 6-Pin Air Unit Cable 2x 8-Pin Cable Wiring Diagram
$53.99
RaceDayQuads Diatone Mamba MK4 F405 Mini 20x20 Flight Controller
The Mamba F405 Mini flight controller is tried and true. This has plenty of features to suit the needs of most quads and pilots. The small for factor and overall reliability make this an excellent choice for almost any build! Check out all of our 20x20 FCs and all our Diatone Gear! Specifications Input Voltage: 3-6S MCU: 480MHz STM32F405 Gyro: ICM42688P OSD: AT7456E Blackbox: 16M Flash Memory Uarts: 6Set ESC Signal: 6Set LED Controller: BF LED I2C: Yes F.Port: Yes Buzz: Yes TVS Protection: Yes BEC: 3.3V 0.5A & 5V 2.5A & 9V 2A Mounting Pattern: 20x20 M3/M2 Dimensions: 29x29.5x6.5 Weight: 6g Includes 1x Diatone Mamba MK4 F405 Mini 20x20 Flight Controller Wiring Diagram
$46.99
RaceDayQuads Fettec FC G4 V1.7 2-6S 30x30 / 20x20 Flight Controller
The FETtec FC G4 V1.7 features the latest STM32G4 processor. Providing unparalleled processing power to your aircraft. Along with an IIM-42652 SPI gyro, two 5v BECs, 6-27V (2-6S) power handling, and a host of other features, the G4 from FETtec is on the cutting edge of Flight Controller technology. Check out our other flight controllers, as well as the rest of our FETtec selection! Dimensions: Maximum outside dimensions: 37,2 x 37,2mm, without outside tips 30 x 30mm Mounting hole arrangement: 20 x 20mm with M2 mounting hole (expandable to M3) 30 x 30mm with M3 mounting hole 30 x 30mm mounting hole tips are removable to reduce overall FC size Specifications Input Voltage: 2-6S LiPo MCU: Latest STM32G473 Processor (w/ 180Mhz + Math accelerator) Gyro: IIM-42652 SPI OSD: YES UARTs: 5 Sets ESC Connections: Yes Firmware: KISS firmware BEC: 5V, 16V Current Sensor: Yes Buzzer: Yes Barometer: No Black Box: No DJI Compatible: Yes Mounting Pattern: 30x30 / 20x20 Dimensions: 37.2x37.2mm Weight: 5.37g Available downloads: Download FETtec FC G4 manual Download FETtec FC G4 v1.7 manual Includes 1x Fettec FC G4 V1.7 2-6S 30x30 / 20x20 Flight Controller 1x 8 pin cable (open on one side) 1x 6 pin cable (open on one side) 1x 4 pin calbe (open on one side)
$79.99
RaceDayQuads FETtec KISS G4-N V1.7 2-6S 30x30 / 20x20 Flight Controller
The FETtec KISS G4-N 2-6S 30x30 / 20x20 Flight Controller features the latest STM32G4 processor. Providing unparalleled processing power to your aircraft. Along with an MPU6000 gyro, two 5v BECs, 6-27V (2-6S) power handling, and a host of other features, the G4 from FETtec is on the cutting edge of Flight Controller technology. Note: This G4-N is a variation on the original G4 and is optimized for digital use. If you are flying analog, you will need the original G4 with built-in OSD chip. Check out our other flight controllers, as well as the rest of our FETtec selection! Specifications Input Voltage: 2-6S LiPo MCU: STM32G4 Gyro:IIM-42652 SPI OSD: No UARTs: 5 Sets ESC Connections: Yes Firmware: KISS firmware BEC: 3.3V, 5V, 16V Current Sensor: Yes Buzzer: Yes Barometer: No Black Box: No DJI Compatible: Yes Mounting Pattern: 30x30 / 20x20 Dimensions: 37.2x37.2mm Weight: 5.37g Includes 1x FETtec KISS G4-N 2-6S 30x30 / 20x20 Flight Controller 1x Capacitor 1x Wiring Harness
$69.99
RaceDayQuads Foxeer F722 V4 Mini 20x20 Flight Controller
Foxeer's V4 F7 FC has a clean layout with high quality components. No more worrying about lifting pads during crashes, this FC has through holes for every solder point. Check out our 20x20 Flight Controllers and all our Foxeer products! Specifications Input Voltage: 2-6S CPU: STM32F722RET6 Gyro: ICM-42688-P BEC Output: DC5V/3A OSD: BF OSD Black Box: 16M Flash Memory UARTs: 4 ESC Telemetry: RX4 Buzzer: YES Smart Audio: YES LED: 1 Set 2812 LED USB: Micro USB Fireware: FOXEERF722V4 Dimensions: 26x26mm Mounting Pattern: 20x20mm Φ4mm Weight: 4g Includes 1x Foxeer F722 V4 Mini 20x20 Flight Controller 4x Vibration Gummies Wiring Diagram
$39.89
RaceDayQuads Foxeer F722 V4 X8 4-8S 30x30 w/ Barometer Flight Controller - MPU6000
The Foxeer F722 V4 X8 4-8S 30x30 Flight Controller is the perfect choice for multirotors. It supports 4-8S input voltage and provides dual BEC and Barometer to ensure safe, efficient and stable operation. The MPU6000 sensor offers accurate and reliable data readings, ensuring excellent flying performance. Included with this Flight Controller is an integrated 5V/10V dual BEC! Check out our 30x30 Flight Controllers as well as Foxeer Collection! Specifications Model: F722 V4 MPU6000 CPU: STM32F722RET6 Gyro: MPU6000 Barometer: DPS310 Power Supply: 4-8S Lipo BEC Output: DC5V/2A; DC10V/2A OSD: BF OSD Black Box: 16M Flash Memory UART: 5 Sets+Rx4 ESC Telemetry: RX4 Buzzer: Yes Connector: DJI/HDZero Smart Audio: Yes LED: 1 Set 2812 LED USB: Type-C Servo: S1,S2 X8: Need CLI Firmware(BetaFlight): FOXEERH743 Size: 37X37mm Mounting Hole: 30.5X30.5mm, Φ4mm Weight(g): 7.7g Working Temperature: -20℃ ~ +55℃ Working Humidity: 20～95% Storage Temperature: -20℃ ~ +70℃ X8 Setup CLI X8 Setup CLI Includes 1x Foxeer F722 V4 X8 4-8S 30x30 Dual BEC Barometer Flight Controller - MPU6000 4x M3 Grommets 1x Cable
$64.89
RaceDayQuads Foxeer H743 Mini X8 4-8S 20x20 Flight Controller - MPU6000
The Foxeer H7 Mini X8 20x20 Flight Controller offers reliable performance with its dual BECs and MPU 6000 gyro. It's capable of operating on 4-8S batteries and boasts a barometer for improved stability and altitude control, making it a great choice for drone enthusiasts. Included with this Flight Controller is an integrated 5V/10V dual BEC! Check out our 20x20 FCs, as well as Foxeer Collection! Specifications Model: Foxeer H7 CPU: STM32H743 Gyro: MPU6000 Barometer: DPS310 Power Supply: 4-8S Lipo BEC Output: DC5V/2A; DC10V/2A OSD: BF OSD Black Box: 16M Flash Memory UART: 6 Sets+Rx8 ESC Telemetry: RX8 Buzzer: Yes Smart Audio: Yes LED: 1 Set 2812 LED USB: Type-C Servo: S1,S2 X8: Supported Firmware(BetaFlight): FOXEERH743 Size: 30X31mm Mounting Hole: 20 x 20mm, Φ4mm Weight(g): 5.6g Working Temperature: -20℃ ~ +55℃ Working Humidity: 20～95% Storage Temperature: -20℃ ~ +70℃ Includes 1x Foxeer H743 Mini X8 4-8S 20x20 Dual BEC Barometer Flight Controller - MPU6000 4x Rubbers Columns
$104.99
RaceDayQuads Foxeer H743 X8 4-8S 30x30 Dual BECs Barometer Flight Controller - MPU6000
The Foxeer H7 is an advanced and reliable 4-8S flight controller with dual built-in BECs and a barometer. It features a fast and powerful MPU6000 processor to provide accurate and consistent performance with less vibration in flight. Enjoy worry-free flying with this top-class controller. Check out our 30x30 Flight Controllers as well as Foxeer Collection! Features 5V/10V Dual BEC MPU6000 32K Flash Rate Plug & Play with Foxeer cameras Specifications Model: Foxeer H7 CPU: FOXEERH743 Gyro: MPU6000 Barometer: DPS310 Power Supply: 4-8S Lipo BEC Output: 3.3V/0.5A;DC5V/2A;DC10V/2A OSD: BF OSD Black Box: 16M Flash Memory UART: 6 Sets+Rx8 ESC Telemetry: RX8 Buzzer: Yes Connector: DJI/HDZero Smart Audio: Yes LED: 1 Set 2812 LED USB: Type-C Servo: S1,S2 X8: Supported Firmware(BetaFlight): FOXEERH743 Size: 37X37mm Mounting Hole: 30.5 x 30.5mm, Φ4mm Weight(g): 7.8g Working Temperature: -20℃ ~ +55℃ Working Humidity: 20～95% Storage Temperature: -20℃ ~ +70℃ X8 Setup CLI X8 Setup CLI Includes 1x Foxeer H743 X8 4-8S 30x30 Dual BEC Barometer Flight Controller - MPU6000 4x M3 Grommets 1x Cable
$104.99
RaceDayQuads HGLRC SPECTER F722 Mini 2-6S 20x20 Flight Controller - MPU6000
The HGLRC SPECTER F722 Mini 2-6S 20x20 Flight Controller boasts a powerful STM32F722 processor with up to 216 MHz of computing power for more seamless control, improved feel, and fast response times. It also features a high-performance MPU6000 gyroscope with 42688 pads for optimum stability and a 16MB black box for plenty of flight data storage. Plus, bluetooth parameter adjustment with the SpeeyBee APP allows you to adjust serial port, PID and other flight control parameters anytime and anywhere. There's even a 10V electronic switch for hassle-free power-on/off and nano-scale coating on both sides to protect against water, moisture, and corrosion. Interested in the HGLRC F760 Mini F722 3-6S 20x20 Stack/Combo (F7 FC / G071 32Bit 60A 4in1 ESC) - MPU6000? Interested in just the HGLRC SPECTER G071 128K 32Bit 60A 3-6S 20x20 4in1 ESC? Check out all our 20x20 FCs, and all of our HGLRC products! Specifications HGLRC SPECTER F722 mini FC FC Firmware: HGLRC F722 Mini MCU: STM32F722 Gyro: MPU6000 OSD: AT7456E Barometer: BMP280 Blackbox 16MB UARTS:5 Input Voltage: 7.4V-22.8V/2-6S LiPO BEC: 10V2A/5V2.5A Size: 37mmx34mmx9.8mm Mounting: 20x20, M3 Weight: 18g Includes 1x HGLRC SPECTER F722 mini flight controller 1x 30AWG 25mm double-ended SH1.0-8P cable 1x 30AWG 70mm single-head SH1.0-7P/single-head SH1.0-6P DJI cable 1x 30AWG 70mm single-head SH1.0-7P/single-head GH1.25-6P VTX cable 1x 30AWG 60mm single-head SH1.0-3P/single-head 1.25-3P camera cable 1x 30AWG 100mm single-head SH1.0-4P receiver cable 4x M3x20 hexagon socket screws
$59.99
RaceDayQuads Hobbywing XRotor F7 3-6S 20x20 / 30x30 Convertible Flight Controller
Take a look at the XRotor F7 Convertible Flight Controller from Hobbywing. This FC is similar to other versions with its OSD, and voltage monitoring, but the F7 now comes with an all-new 5V & 12V dual BEC Circuit and a special interface for the DJI image transmission system. The XRotor F7 Convertible flight controller is equipped with STM32F722 MCU which has a powerful computing ability and fast running speed. High sensitivity ICM20602 six-axis motion sensor, built-in 5V & 12V double BEC, integrated OSD, and a pitch module. Check out our other flight controllers, and our Hobbywing selection! Features Equipped with STM32F722 MCU which has powerful computing ability and fast running speed, and high sensitivity MPU6500 six-axis motion sensor. Supports BetaFlight, Cleanflight, Butterflight, Inva, and other mainstream FPV firmware. DJI image transmission system port equipped with corresponding flat cable Supports bidirectional DShot digital throttle communication. Unique installation design and shock absorption structure. On-board large capacity Flash memory chip. On-board 5V & 12V dual BEC circuit. On-board Pit Switch module. Specifications Firmware: HOBBYWING_XROTORF7CONV FC Programming: Supported Programming via Betaflight/ Cleanflight-configurator Compatible with (Modes) PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600, PROSHOT1000 Compatible with (Transmitters) PPM, Spektrum, SBUS, SUMD, SUMH, XBUS, IBUS, JETIEXBUS, CRSF, SRXL OSD Built-in Input Voltage: 3-6S Gyro: MPU6500 Voltage Monitoring Supported Current Monitoring Supported External Buzzer Supported LED Control Supported BEC 5V @ 1.5A ; 10V @ 1.5A Mounting Pattern: 20x20mm M3 / 30x30mm M3 Size 32x32mm Weight 3.3g Manual Download Includes 1x Hobbywing XRotor F7 3-6S 20x20 / 30x30 Convertible Flight Controller 1x Soft Mounting Grommets Set 1x Signal Cable 1x User Manual
$49.99
RaceDayQuads Holybro Kakute F4 HD V2.4 2-8S 30x30 Flight Controller - MP6000
The Kakute F4 V2.4 is an 8S Flight Controller that has everything you need, with plug-and-play DJI O3 HD camera, 4in1 ESC ports, barometer, OSD, 5x UARTs, logging & onboard flash storage, plus 5V & 9V/3A BEC. DJI HD ready - just plug it in & the 9V/A regulator will power your HD transmitter, like DJI O3 Air Unit & Caddx Vista. There are LED & buzzer pad, I2C pad (SDA & SCL) for external GPS/Magnetometers Check out our other 30x30 flight controllers and the rest of our HolyBro selection! Specifications MCU: STM32F405 IMU: MPU6000 Barometer: BMP280 OSD: AT7456E 5x UARTs (1,3,4,4,6,7) 128 Mbit Dataflash chip Battery input voltage: 2-8S BEC 9V/3A - Optimized for DJI O3 Air unit BEC 5V/2A 7x PWM Outputs (6 Motor Output, 1 LED) Supports serial receivers (SBUS, iBus, Spektrum, Crossfire, ESLR). Mounting: 30 x 30mm, Φ4mm hole with M3 Grommets Dimension: 37x37mm Weight: 7g JST-SH1.0_8pin port (For 4in1 ESCs) JST-SH1.0_6pin port (For DJI/Caddx HD System and other VTX) Includes 1x Holybro Kakute F4 HD V2.4 2-8S 30x30 Flight Controller - MP6000 1x Wiring Kit Wiring Diagram
$39.99
RaceDayQuads Holybro Kakute H7 Mini 20x20 Flight Controller
This new H7 FC from Holybro is a powerhouse with up to 8 motor outputs! Check out our other 20x20 flight controllers, as well as the rest of our HolyBro selection! Specifications Input Voltage: 2-6S MCU: STM32H7 IMU: MPU6000 OSD: AT7456E Uarts: 6 ESC Connections: 8 Firmware Target: KAKUTEH7MINI BEC: 5v/2A Buzzer: Yes Barometer: Yes Stack Size: 20x20 Weight: 5.5g Includes 1x Holybro Kakute H7 Mini 20x20 Flight Controller
$68.59
RaceDayQuads Holybro Kakute H7 V1.3 2-8S 30x30 Flight Controller w/ Bluetooth - MP6000
The 8S capable Kakute H7 boasts Bluetooth, dual 4in1 ESC ports, HD plug, barometer, OSD, 6 UARTs, MicroSD Blackbox, 5V/9V BEC, easy soldering, and more. It builds upon F7 features and has a Bluetooth chip. The SpeedyBee app lets you Betaflight configure/tune wirelessly. It's DJI HD ready and supplies 9V for HD video transmitters. UART2 is for Bluetooth tel., MicroSD for Blackbox, dual 4in1 ESC ports for x8 Octocopter, and BetaFlight OSD for FPV display. LED/buzzer pad, I2C pad for external GPS/Magnetometer. Check out our other 30x30 flight controllers and the rest of our HolyBro selection! Features This V1.3 now has USB-C, 9V 3A BEC for VTX, and JST-SH connector for VTX port. Specifications MCU - STM32H743 32-bit processor running at 480 MHz Professional underfill epoxy for mechanical reinforcement IMU - MPU6000 Barometer - BMP280 OSD - AT7456E Onboard Bluetooth chip - ESP32-C3 SpeedyBee IOS & Android App Compatible Note: The Bluetooth onboard is set to automatically turn off when the flight controller is unlocked (arm) and turn on automatically when the flight controller is locked (disarm) in Betaflight 6x UARTs (1,2,3,4,6,7; UART2 is used for Bluetooth telemetry) 9x PWM Outputs (8 Motor Output, 1 LED) 2x JST-SH1.0 8pin ESC port (4in1 ESCs, x8/Octocopter compatible) 1x JST-SH1.0 6pin VTX port (For HD System like Caddx Vista & Air Unit) Battery input voltage: 2S - 8S BEC 5V 2A Cont. BEC 9V 3A Cont USB Type-C Mounting - 30.5 x 30.5mm/Φ4mm hole with Φ3mm Grommets Dimension - 35x35mm Weight - 8g Includes 1x Holybro Kakute H7 V1.3 3-6S 30x30 Flight Controller w/ Bluetooth - MP6000 1x Wiring Kit Wiring Diagram
$86.99
RaceDayQuads HolyBro Kakute H743-WING 3-8S Fixed Wing Flight Controller
A serious fixed-wing pilot can count on the Holybro Kakute H743 Wing flight controller for powerful operation and reliable performance. Equipped with the STM32 H743 Processor running at 480 MHz, CAN Bus support, dual camera support & switch, 9V/12V ON/OFF Pit Switch, and plug-and-play GPS, and I2C ports, this controller is designed for fixed-wing & VTOL applications. Featuring an intuitive layout, it works with INAV and Ardupilot systems for rapid setup and precise control. Choose between having the pin headers solder on or loose. Check out our other wing flight controllers and the rest of our HolyBro selection! Features STM32H743 MCU running at 480 MHz High-Precision / low-noise ICM-42688-P IMU CAN Bus Support Dual Camera Inputs switch 3 On-board BEC output 5V, 6V/8V and 9V/12V 9V/12V ON/OFF Pit Switch On-board voltage & current sensor Integrated BMP280 barometer Plug-and-play GPS, CAN, I2C ports Small & low-profile design fits into compact frames Supports INAV (6.1.1 & later), Ardupilot (4.4 & later) Holybro Kakute H743-Wing Manual v1.0 Specifications MCU: STM32H743, 480 MHz, 1MB RAM, 2MB Flash IMU: ICM-42688P (SPI3) Baro: BMP280 (I2C4) OSD: AT7456E (SPI2) Blackbox: MicroSD card slot on SDMMC2 7x Uarts (1,2,3,5,6,7,8) with built-in inversion. 14x PWM outputs, 1x CAN, 5x ADC (Bat1/Curr1, Bat2/Curr2 and RSSI) 3x I2C (I2C1 and I2C2 for external devices, I2C4 for onboard sensors) 3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator (Green) USB/DFU Key Extender with USB Type-C Dual Camera Inputs switch 5V/9V(12V) for Camera/VTX power switch High-precision Current Sense (90A continuous, 220A peak) Battery Voltage Sensor: 5K:25.5K (Scale 1800 in INAV, BATT_VOLT_MULT 18.18 in ArduPilot) Static power 160mA@5V Firmware Support Ardupilot Target: KAKUTEH7-Wing(Ardupilot 4.4 or newer) INAV Target: KAKUTEH7Wing (INAV 6.1.1 or newer) PDB Input voltage range: 10~36V (3~8S LiPo) 1x ESC power pads Current Sense: 90A continuous, 220A peak. (Scale 275 in INAV, 36 A/V in ArduPilot) BEC 5V output Designed for FC, Receiver, OSD, Camera, 2812 LED Strip, Buzzer, GPS, Air Speed Sensor, etc. Output 5.15 +/- 0.1V DC Continuous current 2 Amps, 3A Peak BEC 9V /12V output Designed for Video Transmitter, Camera, Gimbal etc. Continuous current 2 Amps, 3A Peak 12V option with Jumper pad BEC Vx output Designed for Servos Voltage adjustable, 6V Default, 8V option with Jumper pad Continuous current 6 Amps, 8A Peak BEC 3.3V output Linear Regulator Continuous current: 200mA Mechanical Mounting: 25 x 25mm, M2 hole Dimensions: 45x 30 x 13.5 mm Weight: 28g with USB extender Includes 1x HolyBro Kakute 3-8S Fixed Wing Flight Controller 1x Power Board 1x Top Board 1x USB-EXT Board 1x GPS Module (Optional) 1x Electrolytic capacitor: 220uF 62v 2x XT60 60mm Power Cable 4x Sets 2.54 DuPont Pin 2x JST-GH 4Pin Cable 1x 15cm JST-SH 6Pin Cable (For USB-EXT Board) Wiring Diagram
$99.99
RaceDayQuads HolyBro Kakute H743-WING 3-8S Fixed Wing Flight Controller & Micro M10 GPS Set
A serious fixed-wing pilot can count on the Holybro Kakute H743 Wing flight controller for powerful operation and reliable performance. Equipped with the STM32 H743 Processor running at 480 MHz, CAN Bus support, dual camera support & switch, 9V/12V ON/OFF Pit Switch, and plug-and-play GPS, and I2C ports, this controller is designed for fixed-wing & VTOL applications. Featuring an intuitive layout, it works with INAV and Ardupilot systems for rapid setup and precise control. Choose between having the pin headers solder on or loose. This Micro GPS uses multi-constellation GNSS powered by u-blox M10, a concurrent GNSS receiver that can receive and track multiple GNSS systems. Owing to the multi-band RF front-end architecture, all four major GNSS constellations, GPS, Galileo, GLONASS, & BeiDou, can be received concurrently. It also comes with the IST8310 compass. Firmware Support for M10 GPS: PX4 1.14, ArduPilot 4.3, INAV 5.0.0, Betaflight 4.3.0 or newer is required. Check out our other wing flight controllers and the rest of our HolyBro selection! Features STM32H743 MCU running at 480 MHz High-precision / low-noise ICM-42688-P IMU CAN Bus Support Dual Camera Inputs switch 3 On-board BEC output 5V, 6V/8V and 9V/12V 9V/12V ON/OFF Pit Switch On-board voltage & current sensor Integrated BMP280 barometer Plug-and-play GPS, CAN, I2C ports Small & low-profile design fits into compact frames Supports INAV (6.1.1 & later), Ardupilot (4.4 & later) Holybro Kakute H743-Wing Manual v1.0 Specifications H743-WING MCU: STM32H743, 480 MHz, 1MB RAM, 2MB Flash IMU: ICM-42688P (SPI3) Baro: BMP280 (I2C4) OSD: AT7456E (SPI2) Blackbox: MicroSD card slot on SDMMC2 7x Uarts (1,2,3,5,6,7,8) with built-in inversion. 14x PWM outputs, 1x CAN, 5x ADC (Bat1/Curr1, Bat2/Curr2 and RSSI) 3x I2C (I2C1 and I2C2 for external devices, I2C4 for onboard sensors) 3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator (Green) USB/DFU Key Extender with USB Type-C Dual Camera Inputs switch 5V/9V(12V) for Camera/VTX power switch High-precision Current Sense (90A continuous, 220A peak) Battery Voltage Sensor: 5K:25.5K (Scale 1800 in INAV, BATT_VOLT_MULT 18.18 in ArduPilot) Static power 160mA@5V Firmware Support Ardupilot Target: KAKUTEH7-Wing(Ardupilot 4.4 or newer) INAV Target: KAKUTEH7Wing (INAV 6.1.1 or newer) Micro M10 GPS GNSS Receiver: Ublox M10 Receiver Number of Concurrent GNSS: Up to 4 (BeiDou, Galileo, GLONASS, GPS, QZSS) Compass: IST8310 Frequency Bands: GPS L1, Galileo E1, GLONASS L1, BeiDou B1, SBAS L1, QZSS L1 Output Protocol: UBX (U-blox), NMEA Nav. Update Rate: Up to 25 Hz (single GNSS) and Up to 10 Hz (4 concurrent GNSS) GNSS Augmentation System (SBAS): WAAS, EGNOS, MSAS GNSS Augmentation System (QZSS): L1S (SLAS) Default Baud Rate: 38400 Input Voltage: 4.7-5.2V Accuracy: 1.5m Speed Accuracy: 0.05 m/s Port Type: JST-GH-6P Antenna: 25 x 25 x 4mm ceramic patch antenna Power consumption: Less than 200mA @ 5V Port Type: JST-GH-6P Operating Temperature: -40~80C Dimension: 32 x 26 x 9mm Weight: 14g Other Notes: LNA MAX2659ELT+ RF Amplifier, Rechargeable Farah capacitance, Rechargeable Farah capacitance PDB Input voltage range: 10~36V (3~8S LiPo) 1x ESC power pads Current Sense: 90A continuous, 220A peak. (Scale 275 in INAV, 36 A/V in ArduPilot) BEC 5V output Designed for FC, Receiver, OSD, Camera, 2812 LED Strip, Buzzer, GPS, Air Speed Sensor, etc. Output 5.15 +/- 0.1V DC Continuous current 2 Amps, 3A Peak BEC 9V /12V output Designed for Video Transmitter, Camera, Gimbal etc. Continuous current 2 Amps, 3A Peak 12V option with Jumper pad BEC Vx output Designed for Servos Voltage adjustable, 6V Default, 8V option with Jumper pad Continuous current 6 Amps, 8A Peak BEC 3.3V output Linear Regulator Continuous current: 200mA Mechanical Mounting: 25 x 25mm, M2 hole Dimensions: 45x 30 x 13.5 mm Weight: 28g with USB extender Includes 1x HolyBro Kakute 3-8S Fixed Wing Flight Controller 1x Power Board 1x Top Board 1x USB-EXT Board 1x GPS Module (Optional) 1x Electrolytic capacitor: 220uF 62v 2x XT60 60mm Power Cable 4x Sets 2.54 DuPont Pin 2x JST-GH 4Pin Cable 1x 15cm JST-SH 6Pin Cable (For USB-EXT Board) Wiring Diagram
$127.98
RaceDayQuads iFlight Blitz F7 Mini V1.1 20x20 Flight Controller
The new iFlight blitz series offers stellar performance at an affordable price. With an F7 processor and high quality BMI270 gyro, this FC is all you could ever need for daily cruising or even hardcore freestyle and racing! Check out our other 20x20 FCs, as well as the rest of our iFlight selection! Specifications MCU: STM32F722 Gyro: BMI270 Barometer: DPS310 OSD Chip: AT7456 Blackbox: 16MB UARTS: 6 Motor outputs: 4x (SH1.0 connector) I2C: SDA / SLA pads LED: Yes Beeper: Yes Firmware Target: IFRC-IFLIGHT_BLITZ_F722 Mounting Pattern: 20x20mm Dimensions: 30.5x27mm Weight: 5g Includes 1x iFlight Blitz F7 Mini V1.1 20x20 Flight Controller Wiring Diagram
$63.99
RaceDayQuads iFlight Blitz F7 V1.1 30x30 Flight Controller
The new iFlight blitz series offers stellar performance at an affordable price. With an F7 processor and high quality BMI270 gyro, this FC is all you could ever need for daily cruising or even hardcore freestyle and racing! Check out our other 30x30 FCs, as well as the rest of our iFlight selection! Specifications MCU: STM32F722 Gyro: BMI270 Barometer: DPS310 OSD Chip: AT7456E Blackbox: 32MB UARTS: 6 Motor outputs: 4x (SH1.0 connector) BEC: 5V 2.5A I2C: SDA / SLA pads LED: Yes Beeper: Yes Firmware Target: IFRC-IFLIGHT_BLITZ_F722 Mounting Pattern: 30.5x30.5mm Dimensions: 36.5x35mm Weight: 7.8g Includes 1x iFlight Blitz F7 V1.1 30x30 Flight Controller Wiring Diagram
$76.99
RaceDayQuads JHEMCU GF30F745 3-6S HD 30x30 Flight Controller - MPU6000
The JHEMCU GF30F745 3-6S 30x30 Flight Controller is ideal for drone pilots who demand high performance. It supports 3-6S and features advanced MPU6000 capabilities for smoother and more accurate flight. Enjoy an improved flying experience with this intuitive and reliable flight controller. Coming within 6pin plug in port designed for HD VTXs like the DJI O3 Air Unit. Check out our other 30x30 FCs, and the rest of our JHEMCU selection! Specifications Chip: STM32F745VG(216MHZ) Gyro: MPU6000 Barometer: DPS310 OSD Chip: AT7456E Black box: 16MM LED Program: Support BB buzzer: Support Input voltage: 3-6S I2C Connector: Support BEC: 5V/2.5A BEC: 10V/2.0A Cam Input: Support USART: UART1,UART2.UART3.UART4.UART6.UART7 Receiver: ELRS(CRSF).TBS(CRSF).SBUS.IBUS.DSM2.DSMX GPS: YES COMPASS: YES HD O3: YES ESC Signal: Dshoot150.Dshot300,Dshot600 USB: TYPE-C Current Port: Yes. Voltage Sensor: Yes DFU Button: YES FC firmware: betaflight_4.4.2_JHEF745.HEX Instal hole: 30.5x30.5x4MM Board size: 36x36MM Weight: 7.5g Includes 1x JHEMCU GF30F745 3-6S 30x30 Flight Controller - MPU6000 4x grommets
$45.99
RaceDayQuads JHEMCU NOXE F4 V2 Deluxe HD 3-6S 20x20 Flight Controller
JHEMCU had a new flight controller aimed at those DJI pilots. This board comes feature-packed and ready for your next build. The 20x20 form factor makes it a perfect fit for nearly any size drone and the 6s capability means that it will be able to keep up with your power needs. The deluxe version supports 16MB black box recording and features a barometer. Check out our other 20x20 flight controllers, as well as the rest of our JHEMCU selection! Specifications Input Voltage: 3-6S LiPo MCU: STM32F411 Gyro: MPU6000 OSD: Yes UARTs: 2 Sets ESC Connections: Yes Firmware: JHEF411 BEC: 5V 3A, 10V 2A Current Sensor: Yes Buzzer: Yes Barometer: Yes Black Box: 16MB DJI Compatible: Yes Stack Size: 20x20 Dimensions: 27x27xmm Weight: 4.5g Includes 1x JHEMCU NOXE F4 V2 Deluxe 3-6S 20x20 Flight Controller
$48.99
RaceDayQuads Matek F405-HDTE 30x30 Flight Controller
Another feature rich offering from Matek in the 30x30 class. Loaded with features for digital and analog builds. Matek leads the pack when it comes to quality and performance. Check out our 30x30 Flight Controllers as well as the entire Matek selection! Features STM32F405 has 1MB flash which can run ArduPilot/INAV/BetaFlight InvenSense the 3rd generation IMU ICM42688-P 9-60V(3~12S LiPo) wide input voltage and voltage sense. and a 9~16V BEC for DJI OSD or analog VTX 8motors+3servos in INAV/BF multirotor mixer. SH1.0_8pin connector for PnP with 2x 4in1 ESC SH1.0_6pin connector for PnP with HD System(Caddx Vista & Air Unit) USB pin breakout for connecting to external USB adapter Specifications Input Voltage: 3-12S MCU: STM32F405RGT6 IMU: ICM42688-P OSD: AT7456E, DJI OSD Barometer: SPL06-001 (I2C) Blackbox: 16M-byte Flash memory UARTs: 6 + 1x Softserial_Tx option PWM outputs: 12 (8x Dshot) I2C: Yes BEC: 5V 1.5A, Vx, 9~16V/1~2A (3S IN/9V 2A, 4S IN/12V 2A, 6S IN/16V 2A, 8S IN/16V 1.5A, 12S IN/16V 1A) ADC: 4 (VBAT, Current, RSSI, Airspeed) PINIO: Yes Dual Analog Camera Cignal Switchable: Yes Mounting Pattern: 30x30mm Dimensions 36x36x5mm Weight: 7g Includes 1x Matek F405-HDTE Flight Controller 6x Silicon grommets M4 to M3 1x SH1.0_8pin cable 5cm, 2x SH1.0_8pin connectors 1x SH1.0_6pin to GH1.25_8pin cable 8cm for HD System(Caddx Vista & Air Unit) Wiring Diagram
$66.99
RaceDayQuads Matek F405-miniTE 20x20 Flight Controller
Another solid choice in the Matek F405-miniTE 20x20 Flight Controller by a company that leads the pack when it comes to quality and performance. Check out all our 20x20 FCs as well as the entire Matek selection! Features F405 has 1MB flash which can run with ArduPilot. even with INAV firmware. Redesigned target MATEKF405TE support 8x bi-directional DSHOT. Support DJI air unit PnP, and a 10V BEC for DJI OSD or analog VTX Compared with F722-miniSE 8motors or 6motor+2servos, F405-miniTE supports 8motors+3servos in INAV/BF multirotor mixer Convertible 20mm to 30.5mm mounting Specifications Input: 6~30V (2~6S LiPo) MCU: STM32F405RGT6 IMU: ICM42688-P OSD: AT7456E Baro: Goertek SPL06-001 (I2C) Blackbox: 16M-byte Flash memory UARTs: 6 PWM outputs: 12 (8 Dshot) I2C: 1 ADC: 4 (VBAT, Current, RSSI, Airspeed) Current Sensor: No PINIO: 2 BEC: 5V 1.7A & 10V 1.4A Mounting Pattern: 20x20 M2/M3, 30X30 M3 Weight: 5g Includes 1x Matek F405-miniTE 20x20 Flight Controller 1x 20mm to 30mm conversion plate(blue PCB) 6x Silicon grommets M4 to M3 6x Brass grommets M3 to M2 1x SH1.0_8pin cable 5cm (including 2x 8pin connectors) for 4in1 ESC 1x SH1.0_6pin to GH1.25_8pin cable 8cm for DJI Air Unit
$66.99
RaceDayQuads Matek F405-WTE Wing Flight Controller w/ Integrated ESP32 & RX
Matek has done it again with another top of the line Matek F405-WTE Wing Flight Controller w/ Integrated ESP32 & RX . This time with an integrated ESP32 module that can be used as an ELRS Receiver of wifi telemetry! You won't find any better quality in the wing game. Check out our other wing flight controllers, as well as the rest of our Matek selection! Specifications Input Voltage 2-6S MCU: STM32F405RGT6, 168MHz , 1MB Flash IMU: ICM42688-P Baro: SPL06-001 OSD: AT7456E Blackbox: MicroSD card slot ESP WiFi Telemetry: Yes(MAVLink, 14dBm) ExpressLRS 2.4G Receiver: Yes(CRSF protocol, Telemetry 12dBm) UARTs: 6 + 1x Softserial_Tx option(INAV) PWM outputs: 12 I2C: Yes ADC: 4 (VBAT, Current, RSSI, Airspeed) Dual Camera Inputs Switch: Yes FC Firmware: ArduPilot: MatekF405-TE, INAV: MATEKF405TE_SD (not available in INAV configurator 4.x) Mounting Pattern: 25x25mm M2 Dimensions: 44x29x12.7mm Weight: 22g BEC Specifications BEC 5V output Designed for Flight controller, Receiver, OSD, Camera, Buzzer, 2812 LED_Strip, Buzzer, GPS module, AirSpeed Continuous current: 2 Amps, Max.3A BEC 9V /12V output Designed for Video Transmitter, Camera, Gimbal ect. Continuous current: 2 Amps, Max.3A 12V option with Jumper pad for stable 9V/12V output, input voltage should > output voltage +1V BEC Vx output Designed for Servos Voltage adjustable, 5V Default, 6V or 7.2V via jumper Continuous current: 8 Amps, Max.10A for stable Vx output, input voltage should > Vx voltage +1V BEC 3.3V output Designed for Baro / Compass module and external 3.3V peripherals Linear Regulator Continuous current: 200mA Includes 1x Matek F405-WTE Wing Flight Controller w/ Integrated ESP32 & RX 1x USB(Type-C)/Beep (Passive buzzer) Extender + 20cm JST-SH-6P to JST-SH-6P cable for USB extender. 2x IPEX-MHF1 2.4G Antennas 1x Rubycon ZLH 35V 470uF capacitor 1x Set Dupont 2.54 pins Wiring Diagram
$74.99
RaceDayQuads Matek F411-WTE Wing Flight Controller
The Matek F411-WTE Wing Flight Controller is a featured packed wing flight controller from Matek that is INAV ready, plenty of UARTS, and 6 PWM output channels. Check out our Fixed Wing collection and all of our Matek Products!ICM42688P version is supported by INAV 6.0 or newer Specifications MCU: 100MHz STM32F411CEU6 IMU: ICM42688P Barometer: SPL06-001 (I2C) OSD: AT7456E (SPI) Blackbox: No Uarts: 2 Full Softserial: 2 PWM outputs: 6 (2x Motors, 4x Servos) I2C: 1 ADC: 4 (VBAT, Current, RSSI, AirSpeed) LEDs for FC STATUS: 3 (Blue, Red) and 3.3V indicator(Red) Built in inverter on UART2-RX for SBUS input Switchable Dual Camera Inputs Vbat power ON/OFF switchable for VTX and camera PPM receiver: not supported Dimensions: 31x26x16.5mm Mounting Pattern: 22x22mm, M2 Power 6~30V DC IN (2~6S LiPo) 132A Current Sense (Scale 250) PDB/Current sense resistor: 90A continuous, 132A burst. BEC 5V 1.5A for FC & Peripherals BEC Vx 5A for servos, 5V/ 6V option Vbat for VTX and camera (ON/OFF switchable) LDO 3.3V 200mA Battery Voltage Sensor: 1k:10k FC Firmware INAV Target: MATEKF411TE ( INAV4.1 or newer) Includes 1x Matek F411-WTE Wing Flight Controller 1x Pin set Wiring Diagram
$39.99
RaceDayQuads Matek H743 Mini V3 20x20 Flight Controller
Packed with features, the H743 Mini from Matek is ready to go. Compatible with INAV, Betaflight, and ArduPilot. Check out our 20x20 FCs as well as the entire Matek selection! Specifications Input Voltage: 2-8S MCU: STM32H743VIT6, 480MHz IMU: ICM42688-P (SPI1) & ICM42605 (SPI4) Baro: Infineon DPS310 (I2C2) OSD: AT7456E (SPI2) Blackbox: MicroSD card socket (SDIO) UARTs: 5.5 (1,2,4,6,7, Rx8) PWM Outputs: 11 I2C: 2 (I2C1/DA1 CL1 pads, no I2C2 breakout) CAN: Yes (C-H, C-L pads) BEC: 5V 1.5A cont. (Max.2A) BEC: 8V 1.5A cont. (Max.2A), 8V outputs stable when Vbat>=10V, 8V outputs 80% of Vbat when Vbat< 10V LDO 3.3V: 200mA VB2 pad supports Max. 69V (voltage divider 1K:20K) Static Power: 200mA@5V with Betaflight, 150mA@5V with ArduPilot ADC: 5 (VBAT, Current, RSSI, VB2, CU2) Dual Camera Inputs Switch: Yes 8V Power ON/OFF Switch: Yes Firmware: MATEKH743 Mounting Pattern: 20x20 M3 Dimensions: 36x28x6.5mm Weight: 7g Includes 1x Matek H743 Mini V3 20x20 Flight Controller 6x Silicon grommets M4 to M3 6x Brass grommets M3 to M2 1x JST-SH1.0_8pin cable, 5cm 2x JST-SH1.0_8pin connectors Wiring Diagram
$95.99
RaceDayQuads Matek H743 Slim V3 30x30 Flight Controller
Packed with features, the H743-Slim from Matek is ready to go. Compatible with INAV, Betaflight, and ArduPilot. Check out our 30x30 Flight Controllers as well as the entire Matek selection! Specifications FC Specifications Brand name: Matek Systems Item name: H743-SLIM Flight Controller MCU: STM32H743VIH6, 480MHz , 1MB RAM, 2MB Flash IMU: ICM42688P & ICM42605 Baro: Infineon DPS310 (I2C2) OSD: AT7456E (SPI2) Blackbox: MicroSD card socket (SDIO) 7x Uarts (1,2,3,4,6,7,8) with built-in inversion. 13x PWM outputs(including “LED” pad) 2x I2C 1x CAN 6x ADC (VBAT, Current, RSSI, Analog AirSpeed, Vbat2, Cur2) 3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red) 1x SPI3 break0ut USB Type-C(USB2.0) 1x JST-SH1.0_8pin connector (Vbat/G/Curr/Rx8/S1/S2/S3/S4) 1x JST-GH1.25_4pin connector (5V/CAN-H/CAN-L/G) Dual Camera Inputs switch 5V/Vbat filtered power ON/OFF switch DJI FPV OSD is supported by any spare UART Power Vbat Input: 6~36V (2~8S LiPo) BEC: 5V 2A cont. (Max.3A) LDO 3.3V: Max.200mA No Current Sensor built-in ADC Vbat2 pad supports Max. 69V (voltage divider: 1K:20K) Static power: 200mA@5V with Betaflight, 150mA@5V with ArduPilot FC Firmware ArduPilot(ChiBiOS): MATEKH743 BetaFlight: MATEKH743 INAV: MATEKH743 (To be supported soon) Physical Mounting: 30.5 x 30.5mm, Φ4mm with Grommets Φ3mm Dimensions: 36 x 36 x 5 mm Weight: 7g Includes 1x Matek H743 Slim 30x30 Flight Controller Wiring Diagram QA: ArduPilot Relay(PINIO Camera-1 and Vsw On by default Make sure 2 cameras are set with identical video format, both PAL or both NTSC. # GPIOs PD10 PINIO1 OUTPUT GPIO(81) //Vsw pad power switch PD11 PINIO2 OUTPUT GPIO(82) //Camera switch # RCx_OPTION: RC input option 28 Relay On/Off 34 Relay2 On/Off 35 Relay3 On/Off 36 Relay4 On/Off e.g. RELAY_PIN 81 //Vsw GPIO RC7_OPTION 28 //Relay On/Off, Use CH7 of Transmitter to switch Vsw RELAY_PIN2 82 //Camera switch GPIO RC8_OPTION 34 //Relay2 On/Off, Use CH8 of Transmitter to switch camera or RELAY_PIN3 81 //Vsw GPIO RC9_OPTION 35 //Relay3 On/Off, Use CH9 of Transmitter to switch Vsw RELAY_PIN4 82 //Camera switch GPIO RC10_OPTION 36 //Relay4 On/Off, Use CH10 of Transmitter to switch camera The configured feature will be triggered when the auxiliary switch’s pwm value becomes higher than 1800. It will be deactivated when the value falls below 1200. Check the pwm value sent from the transmitter when the switch is high and low using the Mission Planner’s Initial Setup >> Mandatory Hardware >> Radio Calibration screen. If it does not climb higher than 1800 or lower than 1200, it is best to adjust the servo end points in the transmitter. Tips ArduPilot Firmware https://firmware.ardupilot.org/Plane/stable/MatekH743/ https://firmware.ardupilot.org/Copter/stable/MatekH743/ INAV is expected to support H743 in 2.6. H743-SLIM has betaflight firmware preloaded for QC BetaFlight target is not on the Github, pls download BetaFlight firmware from our website. If you flash ArduPilot firmware via BetaFlight configurator. there is a known issue that flash process will freeze at 50% if “full chip erase” is selected. Disable full chip erase when flashing, then reset to default in Mission Planner after flashing. It is highly recommended to use STM32CubeProgrammer to erase MCU and upload firmware http://www.mateksys.com/?p=6905
$95.99
RaceDayQuads Matek H743-Wing V3 Flight Controller
Matek's H743-Wing V3 Flight Controller arrives with new features and improvements over the original. This FC features a STM32H743VIT6 MCU running at 480MHz, dual gyros ICM42688-P(SPI1) & ICM42605(SPI4), a DPS310 (I2C2) barometer, and much more. This version features an updated Gyro compared to the V2. Check out our other wing flight controllers, as well as the rest of our Matek selection! Specifications Input Voltage: 3-8S LiPo MCU: STM32H743VIT6 Gyro: ICM42688-P / ICM42605 OSD: Yes UARTs: 8 Sets ESC Connections: Yes Firmware: MATEKH743 BEC: 3.3V, 5V, 9V, 12V Current Sensor: Yes Buzzer: Yes Barometer: Yes Black Box: Micro SD Stack Size: Not Stack Mounted Dimensions: 54x36x13mm Weight: 30g Includes 1x Matek H743-Wing V3 Flight Controller Wiring Diagram
$124.99
RaceDayQuads Matek H743-WLITE Wing Flight Controller
Matek has done it again with another top of the line wing FC. You won't find any better quality in the wing game. These parts are trusted by even the most experienced pilots. Check out our other wing flight controllers, as well as the rest of our Matek selection! Specifications Input Voltage: 2-6S MCU: STM32H743VIH6, 480MHz , 512KB RAM, 2MB Flash IMU: ICM42688-P Baro: DPS310 (I2C2) OSD: AT7456E Blackbox: MicroSD card slot (SDIO) Uarts: 7 (1,2,3,4,6,7,8) with built-in inversion. PWM Outputs: 13(12+LED) ADC: Yes (VBAT, Current, RSSI, Analog AirSpeed, VB2, CU2) Status LED: Yes I2C: Yes (2) CAN: Yes Dual Camera Inputs Switch: Yes High-precision Current Sense: 220A range ADC VB2 voltage divider: 1K:20K ADC AirSpeed voltage divider: 20K:20K FC Firmware: Matek H743 Mounting Pattern: 25x25mm M2 Dimensions: 44x29x14.5mm Weight: 22g BEC Specifications BEC 5V output Designed for Flight controller, Receiver, OSD, Camera, Buzzer, 2812 LED_Strip, Buzzer, GPS module, AirSpeed Continuous current: 2 Amps, Max.3A BEC 9V /12V output Designed for Video Transmitter, Camera, Gimbal ect. Continuous current: 2 Amps, Max.3A 12V option with Jumper pad for stable 9V/12V output, input voltage should > output voltage +1V BEC Vx output Designed for Servos Voltage adjustable, 5V Default, 6V or 7.2V via jumper Continuous current: 8 Amps, Max.10A for stable Vx output, input voltage should > Vx voltage +1V BEC 3.3V output Designed for Baro / Compass module and external 3.3V peripherals Linear Regulator Continuous current: 200mA Includes 1x Matek H743-WLITE Wing Flight Controller 1x USB(Type-C)/Beep (Passive buzzer) Extender 1x 20cm JST-SH-6P to JST-SH-6P cable for USB extender 2x 20cm JST-GH-4P to JST-GH-4P cable for CAN & I2C port 1x Rubycon ZLH 35V 470uF capacitor 1x Set of Dupont 2.54 pins Wiring Diagram
$99.99
RaceDayQuads NeutronRC AT32F435 2-6S 20x20 / 30x30 Flight Controller
Searching for high performance at a low price? Look no further - the NeutronRC AT32F435 Flight Controller is here! Mounting pattern of 20x20/30.5x30.5mm. Betaflight requires a custom target; soon you can update directly from NeutronRC. Suitable for experienced pilots - the tech-savvy flight enthusiast's dream! The AT32F4 doesn’t just offer better bang for your buck compared to the standard STM32 MCU; it blasts the competition right out of the sky. It delivers performance that rivals the STM32 F4, and comes tantalisingly close to matching the STM32 F7. And the best part? It does all this without making your wallet weep. This flight controller runs Betaflight. Yes, it requires a custom target for now, but don’t let that make your propellers droop. Betaflight 4.5 is on the horizon, and it should support the AT32 based flight controller natively. All you need is a dash of patience, and you’ll soon be receiving firmware updates directly from NeutronRC. Please note, that official support will be added to Betaflight soon, for now you will need to download the firmware release and config tools. Check out our other flight controllers and our NeutronRC collection! Features Advanced MCU: Uses a powerful AT32F435CGU7 MCU, boasting a speed of 288M Hz and a 1MB Flash. Exceptional Stability: Integrates a BMI270 gyro driver for superior gyro calibration. Connectivity Options: Offers five Uarts (1,2,3,5,7) and one l2C. High-Quality Components: Uses the FD6288 3in1 driver and an 8-layer 20Z, 2-order blind via PCB. Specifications MCU: AT32F435SE Input voltage: 2-6S Mounting Size: 20x20 or 30x30 Gyro: BMI270 Baro: DPS310 OSD: MAX7456 1x UC 5x Uarts (1,2,3,5,7) USB Type-C Firmware: NEUTRONRCF435SE Important Notes Latest RC Betaflight/ATBetaflight firmware could be found HERE Target is NEUTRONRCF435SE For now ONLY use betaflight configurator BETA to be found HERE future Betaflight 4.5.X to start support AT32 natively soon for ESC Conf. use web ESC Config. found HERE For firmware flashing, Zadig driver needs to be installed HERE USB Virtual Driver HERE CLI W BMI270 Clean build with RPM filters DSHOT300: Includes 1x NeutronRC AT32F435 2-6S 20x20 / 30x30 Flight Controller Wiring Diagram
$26.99
RaceDayQuads NeutronRC Mini F405 2-6S 20x20 / 30x30 Flight Controller
Introducing the NEUTRONRC F405 Mini FC 20x20/30.5x30.5 Hold Flight Controller: a cutting-edge marvel! It offers an ultra-responsive control mechanism and a BMI270 Gyro for smooth maneuvers. Plus, it fits 20x20 and 30x30 setups, and offers OSD for real-time flight data. All this, at an affordable price - grab your NEUTRONRC F405 now and turn the sky into your playground! Check out our other flight controllers and our NeutronRC collection! Features Flexible mounting options: Adapts to 20×20 or 30×30 configurations, making it a perfect fit for any FPV setup. Powered by STM32 F405 MCU: Guarantees rapid and seamless control response for all your aerial stunts. Advanced BMI270 Gyro: Lets your drone glide smoothly, turning the wind into your dance floor. Onboard OSD: Stay on top of real-time flight data and take total control of your flight experience. Pocket-Friendly: Offers high-end performance without breaking the bank, ensuring everyone can fly high. Specifications MCU: STM32F405RG Gyro: ICM-42688 OSD: AT7456E (SPI2) Blackbox: 16M Flash (SP3) Input voltage: 2-6S Mounting Size: 20x20 or 30x30 USB Type-C Baro: Infineon DPS310(12CI) MAG: QMC5883(12CI) Support Betaflight (NEUTRONRCF407) Daul BEC: 5V 2.5A (Max 3A) &12V 2.5A(Max 3A) Current sensor (Scale 100) & Voltage sensor (Scale 110) 4x LEDs for Bat,5V,3.3V,FC Start SH1.0-6pin, DJI/Vista/O3 socket SH1.0-8pin, ESC socket 5x Uarts (1,2,3,4,6) & 1x 12IC Includes 1x NeutronRC Mini F405 2-6S 20x20 / 30x30 Flight Controller Wiring Diagram
$28.99
RaceDayQuads NewBeeDrone Cricket200 V2 F722 3-6S 20x20 Dual BMI270 Flight Controller
Experience top-tier flight performance with the NewBeeDrone Cricket200 V2 F722 3-6S 20x20 Dual BMI270 Flight Controller. This controller features a 3-6S power range, 20x20 mounting, and dual BMI270 processing power for a stable, reliable flight experience. Get ready for smooth, long-distance flight with this advanced drone controller. Check out our 20x20 FCs, and all our NewBeeDrone products! Features Built-in 4 IN 1 ESC socket (including ESC telemetry, External current sensor) JST1.0 8Pin Plug and plug with NBD Cricket200 ESC/Infinity200 ESC. Also compatible with most of the ESC on the market. Built-in solder pads for ESC signal output and power Printed layout instructions ON the board - no need for instructions! DJI FPV Air Unit socket (use UART1 and UART6) 6 UARTS on board. Specifications MCU：STM32F722 - 216MHz Gyro: 2 BMI270 BEC: 5V/3A Interface：6 Mounting Size: 20x20mm Size: 31.5x27mm Input Power: 3-6S Additional Infomation 3V3 100mA 9V 2A 18W Design for DJI FPV Air Unit 5V Camera Power BetaFlight OSD UART1 (Only RX, Air Unit connector) UART2 (Free) UART3 (Free) UART4 (TX and RX connected together for F.Port) UART5 (Only RX, ESC Telemetry) UART6 (MSP/Configuration Port for Air Unit) Firmware can be downloaded HERE. Includes 1x NewBeeDrone Cricket200 V2 F722 3-6S 20x20 Dual BMI270 Flight Controller 4x Grommets short 4x Grommets Long 1x Cricket200 FC to DJI Air module cable 70mm Wiring Diagram
$69.99
RaceDayQuads NewBeeDrone Infinity305 F4 3-6S 30x30 Flight Controller
Premium Controller with Quality Parts and FeaturesFeaturing F4 Processor and 45Amp BLheli32 with NewBeeDrone Smoov-certified hardware design that supports up to 3-6S batteries to provide the best and most reliable quality and performance for either freestyle or racing. Designed to support the DJI Air Unit.Though DJI Air Unit can only support up to 4S, the Infinity300 Stack can make the DJI Air Unite compatible with 6S batteries by providing a 9V 16W clean power for the DJI Air Unit. Plug-and-Play. No need to solder tiny wires.The Infinity300 Stack includes a bundle of wires to connect the Flight Controller and ESC and a bundle of wires to connect the Flight Controller to the DJI Air Unit. No need to solder any tiny wires, making it simple and clean to build. Check out our other flight Controllers and all our NewBeeDrone products! Specifications MCU: STM32F405 CPUE @ 168mhz, can be overclocked IMU: MPU6000 OSD: Betaflight OSD w/ AT7456Ev UART Ports: 6 UARTS USB: Micro USB Input: 3-6S Installing Hole: 30x30mm M3 Weight: 14g Includes 1x NewBeeDrone Infinity305 F4 3-6S Flight Controller 4x Grommets short 4x Grommets Long 1x Infinity305 FC to DJI Air module cable 40mm 1x Infinity305 FC to DJI Air module cable 100mm 1x Infinity305 FC to DJI Air module cable 150mm Wiring Diagram
$49.99
RaceDayQuads RDQ Bardwell F7 V2 3-6S 30x30 Flight Controller - JBF7 V2
The new JBF7 V2 takes everything great about the original JBF7 and adds a few key features that you asked for. Just like the original, it's got an F7 processor, SD card slot for black box logging, and 8 motor outputs. It's got a flexible pad layout that can handle almost any combination of peripherals you could want. Pads are large and heavy--easy for beginners to solder to and reduce the risk of lifted pads. With the new JBF7 V2, we switched to USB-C; we added a VTX pit switch; we added plugs for all of the major features, and we included pre-made plugs for common peripherals, to allow a no-solder or less-solder build for people using those peripherals. We also added small status LEDs for major components, to make troubleshooting easier. For those who like autonomous flight, the board now includes a barometer. Check out all our 30x30 FCs and the full range of RDQ Products! If you have any issues accessing the Black Box features please type out this text in the CLI to get black box data to your SD card "set sdcard_detect_inverted=on" press ENTER, then type "save" and press ENTER. Features Manual written and feature set selected by Joshua Bardwell. Board layout focused on flexibility and resilience. You can build what you want, how you want, without stress. ESC 4-in-1 plug also has solder pads, for troubleshooting, or if you want to direct-solder the ESC. Plug-and-play support for DJI Air Unit. Voltage regulator allows up to 6S input. Eight motor pads for easy resource remapping or for that octo cinelifter you're thinking of building. SD card slot for blackbox logging. All major functions available in SH plugs, and pre-made wire set included for most common peripherals USB-C plug VTX pit switch built-in (9v rail only) allows you to power down the video transmitter using a controller switch Barometer on board (no iNav target at release date, but possible for the future) Status LEDs for major components allow easier troubleshooting 9v regulator rated for 3A. Verified to power HDZero Freestyle and DJI VTX. Joshua Bardwell's Comprehensive Manual Specifications Input Voltage: 3-6S LiPo MCU: STM32F722 Gyro: BMI270 Barometer: DPS310 Power Outputs: 5V 3A, 9V 3A (w/ Pit Switch), 3.3V, vBat BF Target: JBF7 V2 UARTs: 5 (I2C SDA/SCL shared with UART 3) Plugs: 4in1 ESC, RX, Analog Cam, HD Cam, VTX, LED/Buzzer Mounting Pattern: 30.5x30.5mm Weight: 8.3g (w/ gummies & USB Protector) Includes 1x RDQ Bardwell F7 V2 3-6S 30x30 Flight Controller - JBF7 V2 1x 4in1 ESC Cable 1x DJI Air Unit / HD Camera Cable 1x Analog Camera Cable 1x Analog VTX Cable 1x LED / Buzzer Cable 1x Receiver Cable 1x USB-C Protector 1x Set of Gummies Wiring Diagram For in depth wiring instructions, see Joshua Bardwell's Comprehensive Manual
$84.99
RaceDayQuads RUSHFPV Blade F722 HD 3-8S 30x30 Flight Controller - MPU6000
The Rush Blade F722 is a versatile 30x30 for use in various types of builds. DJI compatibility and plugs all around make this FC an incredibly easy platform to build off of! Make sure to check out our other 30x30 Flight Controllers and the rest of our Rush FPV products! Specifications MCU: 216MHz GYRO: MPU6000 OSD: Onboard UARTS: 5 PWM Outputs: 6 Input Voltage: 3-8S BEC: 5V/5A 10V/3A Mounting Pattern: 30.5mm x 30.5mm Includes 1 x Rush FPV Rush Blade F722 30x30 Flight Controller for DJI 2 x 60MM LED/RX Cable 1 x 60MM ESC Cable 1 x 110MM NAVI Cable 1 x 110MM Air Unit Cable 5 x 8MM Grommet 5 x 5MM Grommet Wiring Diagram
$63.99
RaceDayQuads SkyStarsRC F7 Mini HD Pro 3-6S 20x20 Flight Controller
SkyStarsRC's F722 Mini HD Pro 20x20 Flight Controller, with F7 processor, 6 UARTS, and a 10V 2A Regulator for Caddx Vista or DJI Air Unit! Plus includes Barometer and Blackbox! Check out all our 20X20 FCs! and our SkystarsRC collection! Specifications SkyStarsRC F7 Mini HD Pro 3-6S 20x20 Flight Controller MCU: STM32F722RGT6 216MHz IMU(Gyro): BMI270 USB Port: Type-C Barometer: yes OSD Chip: AT7456E chip DJI Air Unit Connection: 6-pin connector and solder pads Blackbox 16MB Current Sensor: Supported Power Input: 3S-6S LiPo Power Output: 5V 2A & 10V 2A ESC Signal: M1-M4 available UART: 6 Sets I2C: Supported LED: Supported Buzzer: Supported Firmware Target: SKYSTARS F7HDPRO Mounting: 20x20mm Dimensions: 31x30x7.8mm Weight: 6g INCLUDES: 1 x SkyStarsRC F7 Mini HD Pro 3-6S 20x20 Flight Controller
$47.99
RaceDayQuads SkyStarsRC F722 RS 3-6S 20x20 Flight Controller - MPU6000
Discover smooth and stable flight with the SkyStarsRC F722RS Flight Controller. It boasts a 3-6S support & 20x20 mounting. This FC features an MPU6000 sensor that gives you reliable performance. Fly confidently, knowing your controller is up to the task. Check out all our 20x20 FCs, and our SkyStarsRC collection! Specifications MCU: STM32F722RGT6 216MHz IMU: MPU6000 (SPI) OSD: Betaflight OSD & DJI HD OSD (UART6) 6 hardware UARTS (UART1,2,3,4,5,6) Barometer: NO Buzzer Pad: YES BEC: 5V 3A Input Voltage: 3-6S Lipo Blackbox: 16MB Firmware: SKYSTARS F7RS Dimensions: 26x28x7mm Mounting Holes: Standard 20mm/M3 square to center of holes Weight: 4.9g Includes 1x SkyStarsRC F7RS 3-6S 20x20 Flight Controller
$44.99
RaceDayQuads SkyStarsRC H7 Single Gyro 2-6S 30x30 Flight Controller
SkyStarsRC's flagship H743 Flight Controller with X8 support, OSD, BMI270 gyro, BMP280 barometer, 16M BlackBox, 8 UARTS, and more. The powerful MCU running at 480MHz should future-proof any new firmware updates coming in the next few years. Check out all our 30x30 FCs! and our SkystarsRC collection! Specifications SkyStarsRC H7 Single Gyro 2-6S 30x30 Flight Controller MCU: STM32H743VIT6, 480MHz , 1MB RAM, 2MB Flash IMU(Gyro): BMI270 USB Port: Type-C Barometer: BMP280 OSD Chip: AT7456E chip DJI Air Unit Connection: 6-pin connector and solder pads Blackbox 16Mb Current Sensor: Supported Power Input: 2S-6S LiPo Power Output: VTX 10V/Vbat filtered power ON/OFF switch ESC Signal: M1-M8 available UART: 8 Sets I2C: Supported LED: Supported Buzzer: Supported Firmware Target: Betaflight - SKYSTARSH7HD Mounting: 30.5 x 30.5mm ( 4mm hole diameter ) Dimensions: 39.5 x 39.5 x 7.8mm Weight: 10.1g INCLUDES: 1 x SkyStarsRC H7 Single Gyro 2-6S 30x30 Flight Controller
$61.99
RaceDayQuads Speedybee F405 Mini 3-6S 20x20 Flight Controller
Utilizing an upgraded F405 flight controller chip with better performance than the F411, it features a built-in Bluetooth chip for seamless wireless Betaflight tuning. The board comes with a 4-level battery voltage display, built-in barometer, and supports connectivity to all DJI Air Units. It offers 4 available UART ports, and a dual BEC setup with 5V 2A and 9V 3A outputs. Check out all our 20x20 FCs, as well as the rest of our SpeedyBee products! Specifications MCU: STM32F405 IMU(Gyro): ICM42688P USB Port Type: Type-C Barometer: Built-in OSD Chip: AT7456E chip BLE Bluetooth: Supported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Please make sure the MSP switch on UART 4 is turned on and set to a baud rate of 115200, otherwise Bluetooth functionality will not be available. Wireless FC Firmware Flashing: NOT Supported. Please connect to the Betaflight configurator on the PC to do FC firmeare update Wireless Blackbox Download & Analysis: NOT Supported. Please connect to the Betaflight configurator on the PC to do blackbox analysis. WIFI: Not supported DJI Air Unit Connection Way: Direct soldering DJI Air Unit Compatibility: Compatible with all DJI Air Units: DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1. Please use the solder pads < 9V, G, T1, R1, G, SUBS(R2) > on the front right corner of the flight controller to make a pin-to-pin connection with the solder pads on the DJI Air Unit. UART1(T1, R1) is used for OSD and SUBS(R2) is used for DJI Air Unit’s internal SBUS receiver signal input. Blackbox: 8MB Onboard Flash BetaFlight Camera Control Pad: Yes(CC pad on the front side) Current Sensor Input: Supported. For SpeedyBee BLS 35A V2 ESC, please set Scale=250 and Offset=-500. Power Input: 3-6S LiPo. The flight controller is powered through the G, V wires of the 8pin harness or G, V pads from the bottom side of the flight controller. 5V Output: 4 groups of 5V output, three +5V pads and 1 BZ+ pad( used for Buzzer) on front side. The total current load is 2A. 9V Output: 1 group of 9V output, one +9V pad on front side. The total current load is 3A. 3.3V Output: Supported. Soldering pad named ‘3V3’ on the front top of the flight controller. Designed for 3.3V input receivers. Up to 500mA current load. 4.5V Output: Supported. Designed for radio receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load. ESC Signal: M1 - M4 wires or soldering pads on bottom side. UART: 6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6 ESC Telemetry: UART R5(UART5) I2C: Supported. DA & CL pads on front side. Used for magnetometer, sonar, etc Traditional Betaflight LED Pad: Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LEDs controlled by the Betaflight firmware. Buzzer: BZ+ and BZ- pad used for 5V Buzzer BOOT Button: Supported. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked. RSSI Input: Not Supported Smart Port / F.Port: Not Supported Supported Flight Controller Firmware BetaFlight(Default), INAV Firmware Target Name: SPEEDYBEEF405MINI Mounting: 20 x 20mm 3.5mm hole diameter, Compatible with M2 and M3 screws/Silicone grommets. Dimension: 30(L) x 32(W) x 7.8(H)mm Weight 9.6g Includes 1x Speedybee F405 Mini 3-6S 20x20 Flight Controller Wiring Diagram
$31.99
RaceDayQuads SpeedyBee F405 V3 3-6S 30x30 Flight Controller
The new SpeedyBee F405 V3 FC. They now come with a whole new set of features like a built-in cell checker on the FC, a built-in barometer for long-range pilots, and of course seamless integration of the Speedybee Bluetooth app to be able to configure and adjust settings anywhere with your drone! Check out all our 30x30 FCs and all our Speedy Bee products! Specifications F405 V3 Flight Controller MCU: STM32F405 IMU: BMI270 USB: Type-C Baro: built-in OSD: BetaFlight OSD w/ AT7456E chip BLE Support, used for Flight Controller configuration WiFi Support, used for data transfer, e.g firmware flashing, and Blackbox analysis. DJI Air Unit plug: A full DJI Air Unit JST slot onboard BlackBox: Betaflight firmware requires the type of microSD card to be either Standard (SDSC) or High Capacity (SDHC), so extended capacity cards (SDXC) are not supported(Many high-speed U3 cards are SDXC). Also, the card MUST be formatted with the FAT16 or FAT32 (recommended) filesystems. So, you could use any SD card less than 32GB, but Betaflight can only recognize 4GB maximum. BetaFlight Camera Control Pad: Yes Power input: 3S - 6S Lipo 9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on the front side, and 4x LED 5V pads. The total current load is 2A. 2 groups of 9V output, one +9V pad on the front side and the other included in a connector on the bottom side. The total current load is 2A. Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load. Supported. Designed for 3.3V-input receivers. Up to 500mA current load. ESC signal M1 - M4 on the bottom side and M5-M8 on the front side. UART: 5 sets (UART1, UART2, UART3, UART4, UART6) ESC Telemetry: UART UART4 RX I2C: Supported. SDA & SCL pads on the front side. Used for magnetometer, sonar, etc. LED: Used for WS2812 LED controlled by Betaflight firmware. Buzzer: BZ+ and BZ- pad used for 5V Buzzer Boot button: Yes RSSI input: Yes SmartPort: Supported Support Flight Controller Firmware: BetaFlight(Default), EMUFlight, INAV Target: SPEEDYBEEF7V3 Mounting: 30.5x30.5mm, 4mm hole size Dimension 41.6(L) x 39.4(W) x 7.8(H)mm Weight 9.6g Includes 1x SpeedyBee F405 V3 30x30 Flight Controller 1x SH1.0mm 8pin 30mm Cable 5x Silicone grommet M3 8.1mm 1x DJI 6pin Cable (80mm) Manual F405 V3 Manual
$34.99
RaceDayQuads SpeedyBee F405 V4 3-6S 30x30 Flight Controller
Introducing the SpeedyBee F405 V4 flight controller with dual gyroscope power supply filtering, 4-level battery indicators, support for up to 8 motors, 4x LED strip soldering pads, 3A 5V & 9V BECs, and fixed SD card compatibility issue. Change motor direction wirelessly and quickly get set up with the DJI Air Unit plug-and-play set up. Plus, onboard barometer is included. Interested in the SpeedyBee F405 V4 BLS 3-6S 30x30 Stack/Combo (F405 FC / 8Bit 55A 4in1 ESC)? Interested in the SpeedyBee BLS 8Bit 55A 3-6S 30x30 4in1 ESC? Check out all our 30x30 stacks & combos, and all our Speedy Bee products! Features User manual Wireless FC & ESC full configuration Dual gyroscope power supply filtering Onboard 4-level battery indicators Supports up to 8 Motors 4x LED strips soldering pads 5V & 9V BECs upgraded to 3A output Fixed SD card compatibility issue Change motor direction wirelessly DJI Air Unit plug-and-play Built-in barometer Specifications SpeedyBee F405 V4 30x30 Flight Controller MCU: STM32F405 IMU(Gyro): ICM42688P USB Port Type: Type-C Barometer: Built-in OSD Chip: AT7456E chip BLE Bluetooth: Supported. Used for Flight Controller configuration (MSP should be enabled with Baud rate 115200 on UART4) WIFI: Not supported DJI Air Unit Connection Way: Two ways supported: 6-pin connector or direct soldering. 6-pin DJI Air Unit Plug: Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.Blackbox MicroSD Card Slot: Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High capacity (SDHC) under 32GB, so extended capacity cards (SDXC) are not supported(Many high-speed U3 cards are SDXC). Also the microSD card MUST be formatted with the FAT16 or FAT32 (recommended) format, you could use any SD card less than 32GB, but the Betaflight can only recognize 4GB maximum. Current Sensor Input: Supported. For SpeedyBee BLS 55A ESC, please set scale = 400 and Offset = 0. Power Input: 3S - 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side) 5V Output: 9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 3A. 9V Output: 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 3A. 3.3V Output: Supported. Designed for 3.3V-input receivers. Up to 500mA current load. 4.5V Output: Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load. ESC Signal: M1 - M4 on bottom side and M5-M8 on front side. UART: 6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6 ESC Telemetry: UART R5(UART5) I2C: Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc. Traditional Betaflight LED Pad: Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware. Buzzer: BZ+ and BZ- pad used for 5V Buzzer BOOT Button: Supported.[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.[B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware. RSSI Input: Supported. Named as RS on the front side. Smart Port / F.Port: Not supported Supported Flight Controller Firmware: BetaFlight(Default), INAV Firmware Target Name: SPEEDYBEEF405V4 Mounting: 30.5 x 30.5mm( 4mm hole diameter) Dimension: 41.6(L) x 39.4(W) x 7.8(H)mm Weight: 10.5g Includes 1x SpeedyBee F405 V4 3-6S 30x30 Flight Controller Wiring Diagram
$36.99
RaceDayQuads SpeedyBee F405 WING APP 2-6S Fixed Wing Flight Controller
The SpeedyBee F405 WING APP flight controller has been tailor-made for FPV fixed-wing pilots. Its STM32 F405 MCU and ICM-42688-P IMU, 6 UARTS, and Bluetooth enable superb performance and unbeatable flying. You get top-notch features, such as OSD, a barometer and an onboard RGB battery indicator, all at an amazing price. Wireless setup is simple, and very minimal soldering is needed with all the plugin ports. It supports both INAV and Ardupilot firmware, and Ardupilot's VTOL function too! This amazing wing flight controller will allow you to use up to 11 PWM outputs to be configured for motors and servo control. Check out our other wing flight controllers, and our SpeedyBee products! Features Wireless configuration Easy installation, plug and play - no soldering needed Dual firmware support for INAV and Ardupilot Support Ardupilot's VTOL function F405 all pins break out Multilayer board design, stable operation CRSF telemetry data displayed by Lua script 4x LED strip plugs, lighting style On-board current sensor, with 3 BEC outputs Includes 90° pin headers, for lower installation height Specifications SpeedyBee F405 WING FC board MCU: STM32F405,168MHz,1MB Flash IMU(Gyro&Accelerometer: ICM-42688-P Barometer: SPL006-001 OSD Chip: AT7456E Blackbox: MicroSD Card Slot UART: 6 sets(USART1, USART2, USART3, UART4, UART5, UART6(Dedicated for Wireless board Telemetry connection)) I2C: 1x Used for magnetometer, digital airspeed sensor ADC: 4x (VBAT, Current, RSSI, Analog AirSpeed) PWM: 12x (11+1“LED”pad) ELRS/CRSF receiver: Supported,connected to UART1 SBUS: Built in inverter for SBUS input (UART2-RX) LED: 3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator(Red) 1x RGB RSSI: Supported, Named as RS . Supported FC Firmware: INAV:SpeedyBeeF405WING(default)ArduPilot: SpeedyBeeF405WING Weight: 8.9g SpeedyBee F405 WING PDB board Input voltage range: 7~36V (2~6S LiPo) Battery Voltage Sensor: Connect to FC board VBAT, 1K:10K (Scale 1100 in iNav, BATT_VOLT_MULT 11.0 in ArduPilot) Battery Current Sensor: 90A continuous, 215A peak Connect to FC board Current (Scale 195 in iNav, 50 A/V in ArduPilot) TVS Protective diode: Yes FC BEC output: Output 5.2V +/- 0.1V DC Continuous current 2.4 Amps, 3A Peak Designed for FC, Receiver, GPS module, AirSpeed module, Telemetry module, WS2812 LED_Strip VTX BEC output: Output 9V +/- 0.1V DC Continuous current 1.8 Amps, 2.3A Peak Voltage adjustable, 9V Default, 12V or 5V via jumper Designed for Analog Video Transmitter,Digital Video Transmitter, Camera. Servo BEC output: Output 4.9V +/- 0.1V DC Continuous current 4.5 Amps, 5.5A Peak Voltage adjustable, 4.9V Default, 6V or 7.2V via jumper Designed for Servos. Weight: 11.4g SpeedyBee F405 WING Wireless board Wireless Configuration (long press BOOT button for 6 seconds to switch modes) BLE mode, connect to Speedybee APP Wi-Fi mode, connect to QGroundControl APP, Speedybee APP, MissionPlanner, etc. Classic Bluetooth SPP mode, connect to QGroundControl APP, MissionPlanner LED strip controller (short press BOOT button to switch effects, long press 2 seconds to switch modes) 4x WS2812 LED strip connectors, adjustable colors and flashing modes Max 5.2V 1.3A, supports around 70pcs 5050 WS2812 LED beads On-board battery level indicator: 4x RGB indicator LED for battery level display by a number of lights Weight: 4.2g Includes 1x SpeedyBee F405 WING APP Fixed Wing Flight Controller Wiring Diagram
$39.99
RaceDayQuads SpeedyBee V3 F722 3-6S 30x30 Flight Controller
The improvements to the SpeedyBee V3 F722 3-6S 30x30 Flight Controller are staggering! This flight controller comes with onboard Wi-Fi which boasts 33% faster wireless firmware flashing and full Betaflight Configuration. With an optimized algorithm and upgraded Bluetooth/Wi-Fi chip, you can dive into your Blackbox data every time you land your quad. Just take your smartphone out, connect, and download your flight in 20 seconds. The path to progress has never been easier. As if that weren't enough, this FC can support up to 8 motors and has solder-free plugs for your VTX, RX, camera, GPS, and 4x LED strips. If you hate soldering, this is the Flight Controller for you! Browse all our 30x30 flight controllers and all our Speedy Bee products! Features DJI Plug and Play Built in Wi-Fi and Bluetooth Camera control pad Blackbox 6 Uarts, buzzer pad, and I2C Specifications MCU: STM32F722 IMU: BMI270 USB: Type-C Baro: BMP280 (I2C) OSD: BetaFlight OSD w/ AT7456E chip BLE Support, used for Flight Controller configuration WiFi Support, used for data transfer, e.g firmware flashing, and Blackbox analysis. DJI Air Unit plug: A full DJI Air Unit JST slot onboard BlackBox: 500MB onboard data flash BetaFlight Camera Control Pad: Yes Power input: 3S - 6S Lipo 10 groups of 5V output, three +5V pads and 1 BZ+ pad (used for Buzzer) on front side, and 6 +5V output included in the connectors on bottom side. The total current load is 2A. 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 4A. Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load. Supported. Designed for 3.3V-input receivers. Up to 500mA current load. ESC signal M1 - M4 on bottom side and M5-M8 on front side. UART: 5 sets (UART1, UART2, UART3, UART4, UART6) ESC Telemetry: UART UART4 RX I2C: Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc. LED: Used for WS2812 LED controlled by Betaflight firmware. Buzzer: BZ+ and BZ- pad used for 5V Buzzer Boot button: Yes RSSI input: Yes SmartPort: Supported Support Flight Controller Firmware: BetaFlight(Default), EMUFlight, INAV Target: SPEEDYBEEF7V3 Mounting: 30.5x30.5mm, 4mm hole size Dimension: 41(L) x 38(W) x 8.1(H)mm Weight: 9g Includes 1x SpeedyBee F7 V3 30x30 Flight Controller Wiring Diagram
$62.99
RaceDayQuads T-Motor F60A Mini 4-8S 20x20 4in1 ESC
T-Motor enters the world of ESCs yet again with another that is sure to impress! 8S capable with monster mosfets! This ESC is ready to spin props and spin them fast!! Check out all our 20x20 FCs and all our T-Motor products! Specifications Input Voltage: 3-8S LiPo Max. Continuous Current: 60A Max Burst Current: 70A Telemetry: Yes Firmware: BLHeli_32 Input Signal: DShot 150/300/600/1200/MultiShot/OneShot Mounting Pattern: 20x20mm M3 Dimensions: 36x47mm Weight: 14g Includes 1x T-Motor F60A Mini 4-8S 20x20 ESC
$89.89
RaceDayQuads T-Motor F7 HD 30x30 Flight Controller
The T-Motor F7 Flight Controller now comes in a version meant specifically for the DJI Digital FPV System! Including a plug for your Air Unit and a 10V 2A BEC to power it. Check out all our 30x30 Flight Controllers, all our DJI compatible gear, and all our T-Motor products! Specifications Input Voltage: 3-6S Gyro: BMI270 Master chip: STM32F722RET6 Flash: 16MB BEC: 5V 2A, 10V 2A Mounting hole: 30.5x30.5mm Weight: 8.4g Size: 37x37mm Firmware: TMOTOR F7(Betaflight) Includes 1x T-Motor F7 HD 30x30 Flight Controller for DJI Wiring Diagram
$62.89
You have seen 48 out of 56 products